Desoldering Wire 2mm

Ultraviolet ray detection module 200-370nm with a supply voltage of 3.3-5 VDC and a very low consumption of 0.1mA.
100% compatible UNO module.
Characteristic:
- Operating voltage: 3.3-5 VDC
- Output voltage: 0-1 VDC
- 3-pin connector:
- OUT: output signal
- VCC: Supply voltage
- GND: Ground connection - Test accuracy: ± 1UV INDEX
- Current: 0.06mA (typical), 0.1mA (maximum)
- Wavelength of the response: 200nm-370nm (ultraviolet rays) - Response time: less than 0.5 seconds
- Operating temperature: -20ºC - + 85ºC
- Size: 19.80 x 15mm

15x Electrolytic Capacitor 22uF 25V 105ºC PIC Arduino features:
-Type: Electrolytic Capacitor
-Assembly: intern
-Value: 22uF
-Maximum tension: 25V
-Maximum temperature: 105º C
-Dimensions: 5x11mm
-Quantity: 15 units

5x Electrolytic Capacitor 1000uF 35V 105ºC PIC Arduino features:
-Type: Electrolytic Capacitor
-Assembly: intern
-Value: 1000uF
-Maximum tension: 35V
-Maximum temperature 105º C
-Dimensions: 13x21mm
-Quantity: 5 units

Flux Solder Paste in Tin Can 40g features:
- Welding paste according to DIN EN 29454-1 1.1.2.C
- Flux paste based on medium activity rosin
- Easy to solder: copper, silver plated, zinc and nickel Flux residues after welding do not cause corrosion of non-ferrous metals and may remain in the joints.
Operating temperature of up to 350 C.

- It has an Atmega328P chip running at 16Mhz with a factory loaded bootloader - The Uno R3 module has all the connectors than the Arduino Uno R3 and is compatible with all Arduino shields Arduino compatible UNO R3 board features:
- Includes USB Cable - ATmega328P 16MHz chip with external quartz crystal
- Microprocessor: ATmega328
- Operating voltage: 5V
- Input voltage (recommended): 7-12V
- Input voltage (limits): 6-20V
- Clock speed: 16 MHz
- Digital I / O Pins: 14
- Analog input pins: 6
- DC current per I / O Pin: 40 mA
- DC Current per Pin 3.3V: 50 mA
- Flash32 KB of which 0.5 KB are used by the bootloader - Atmega328
- SRAM 2 KB - Atmega328

Type of chemical preparation: alcoholic stripper of printed PCB plates.
Alcohol-based cleaner to eliminate fluxes, dirt removal, flux residues in PCB.
has low impact on electronic components.
Alcohol PCB Cleaner 1l features:
- Form: liquid
- Capacity: 1l
- Alcohol PCB cleaner
PCB cleaner based on alcohol for the elimination of any residue from the printed circuit surfaces after welding, cleaning of the welding unit frames, templates and rosin screens, and the dissolution of the waste stream.
The liquid does not affect the substrate or components of the circuit board.

Level sensor for liquids with float. The liquid level sensor acts as a switch. Liquid level float sensors are used when constant control and regulation of the liquid level (water, oil and other fluids) is required such as extraction pumps. The sensor is equipped with a float with a magnet which, acting by the buoyancy force of the fluid, moves along the tube, shortening or opening the reed switch.

It can be used to detect liquid levels that are too high or too low. Ideal for all those applications where the level of non-corrosive liquids such as water tanks or aquariums needs to be monitored. It is made of stainless steel.

CNC Shield + UNO R3 CH340 +4x A4988 Stepstick 3D Printer Arduino kit features:
- Content:
* 1x UNO R3 CH340 Compatible with Arduino
* 1x CNC Shield V3
* 4x A4988 Drivers
* 4x Heatsinks for A4988
* Jumpers