Transparent Acrylic Box R3 for Arduino Uno Protection box for Arduino UNO R3 made of high quality acrylic material. Arduino Uno Transparent Acrylic Box R3 features: - Compatible with Arduino UNO - Material: transparent acrylic - External dimensions: 80x 65x 18.5mm Code B0013 Available Price €1.95
16x2 1602 LCD display Blue IIC/I2C LCD display consists of a 16-character, 2-rows. The display is compatible with the HD44780 controller Ideal for projects with Arduino You can use it with PIC, AVR, STM32 and many more controllers. Code P0010 Available Price €4.89
Heart Rate Oximetry Sensor Module for Arduino MAX30100 This detection module that allows you to detect your heart rate and blood oxygen level from your Arduino project. You can monitor your blood oxygen level yourself to avoid going to the doctor or pharmacy on purpose. Simply press the sensor with your finger and wait for the reading of hemoglobin (Spo2), heart rate and Perfusion Index (PI%). It is a solution as an integrated heart rate sensor and pulse oximetry, which includes two LEDs, a photodetector and is optimized for analog low noise optics. Code S0148 Available Price €5.95
Servos Tester Servos Tester features: - 3-Channel Tester - For Electronica Arduino Code R0029 Available Price €2.95
Platform camera + 2 SG90 Servo Motor 9g Kit for Arduino Platform camera + 2 SG90 Servo Motor 9g Arduino Kit features: - Operating voltage: 3.0-7.2V- Speed (4.8V without load): 0.12sec / 60 degrees- Force: 1.2kg / 42.3oz (4.8V), 1.6kg / 56.4oz (6.0V)- Working temperature: -30 to +60 Degree C- Cable length: approx. 23cm- Includes photo accessories and screws- Dimensions: 22x11.5x27mm Contents: - Servo 9g - 2 units- Platform for camera - 1 unit Code R0021 Available Price €4.99
Mini Submersible Water Pump USB DC 5V 2-3L/Min 5V USB powered water pump. Submersible pump for aquariums. It doesn't make a lot of noise while you're working. Code M0219 Available Price €3.69
L298N Motor Drive Controller Board Module Dual H Bridge DC It allows controlling up to 2 direct current motors or a bipolar stepper motor. It also allows to control a unipolar stepper motor configured as bipolar.Ideal for projects with ARDUINO.You can use it with PIC, AVR, STM32. L298N Motor Drive Controller Board Module Dual H Bridge DC features: - Minimum operating voltage: 5 V- Maximum operating voltage: 35 V- Maximum current: ± 2 A- Logic voltage: 5V- PWM signal inputs for speed control- Outputs: for 2 DC motors or for a bipolar stepper motor- Measures: 43x43x24 mm Helpful Links: Operation of the robot by Infrared / Operation of the robot by Bluetooth / Automatic operation with detection of obstacles Code M0100 Available Price €2.79
Seeed Grove Inventor Kit for micro:bit The Grove inventor kit is a great extension set for your micro:bit. By using Grove shield for micro:bit you are able to connect all the modules included in the pack purely by the Grove connectors with no need to solder or wire any parts. Now you can focus only on programing with your great mirco:bit. Code SS005 Available Regular price €69.90 -€20.00 Price €49.90
Digital Compass GY-273 Compas Magnetometer Three-axis electromagnetic field sensor module GY-273 including the HMC5883L chip that specifies the direction of the magnetic field of the ground. Digital Compass GY-273 Compas Magnetometer features: Supply voltage: 2.16 - 3.6 VDC, I2C interface with SCL, SDA, signals - Measurement range: 1.3 to 8 Gauss, Measurement resolution: 12 bits, Measurement accuracy: 0.73 - 4.35 Gauss, Transmission speed 400kHz, Sensitivity 230-1370 LSB / Gs, Output frequency: 75Hz, DRDY pin interruption, Dimensions of 18 mm x 13 mm. Code M0179 Available Price €3.79
Black UV sensor module UVM-30 for Arduino UVM-30A sensor module suitable for any location and requires stable and precise measurement of UV light. Ideal for Arduino projects. Black UV sensor module UVM-30 for Arduino features: - Operating voltage: 3-5 VDC, - Voltage input: DC 0-1 VDC, - 3-pin connector: - GND (-): ground connection, - Out: sensor output signal, - VCC (+): sensor supply, - Measurement accuracy: +/- 1UV index, - Working current: 0.06mA (standard) / 0.1mA (max.), - Response wavelength: 200-370 nm, - Working temperature: -20ºC - + 85ºC, - PCB size: 28x12mm. Code M0178 Available Price €9.95
Thermistor NTC 50.0K 5% MF52A epoxy resin coating resistor NTC thermistor - with a negative temperature coefficient, i.e. an increase in temperature causes a decrease in resistance. Thermistor NTC 50.0K 5% MF52A epoxy resin coating resistor features:Size: 3mmRated resistance: R25 = 50.0kB value 25/85 = 3950°KRated power: ‰¤ 50mWTolerance:± 5%Operating temperature: from -40°C to +125°C Tinned steel wire 25mm Code D0091 Available Price €0.49
HC-SR501 Motion Detector Module Passive Infrared PIR Sensor Arduino compatible IR motion detector with a detection range of 7 meters and an operating angle of 120º. An electric pyro sensor , which can detect infrared radiation levels - detect a change in the average IR levels of your detection zone. Ideal for projects with ARDUINO, PIC, AVR, STM32. HC-SR501 Motion Detector Module Passive Infrared PIR Sensor features: - Infrared sensor with control circuit - Adjustable sensitivity and time - Operating voltage: 4.5V- 20V - Consumption in Idle state: Code S0003 Available Price €1.79
SparkFun Weather Meter Kit The SparkFun weather meter kit is a set of basic mechanical components for building a weather station. This kit represents the three basic elements of weather measurement: wind speed, wind direction and precipitation. Whether you are a farmer, a professional meteorologist or a weather enthusiast, building your own weather station can be a truly rewarding project. However, when it comes to measuring the weather, you need some pretty specialised sensors. Code SP090 Backorder Price €109.90
Sensor Module FZ0888 IR Infrared Speed Meter Sensor Module FZ0888 IR Infrared Speed Meter features: - The FZ0888 encoder module is a device that can help you in the creation of your robotics and automation project, Whether you want to know the speed of a motor or its exact position - The module has a digital output (DO) which can be connected to your preferred microcontroller. The operating mode: - When the sensor is blocked, the DO output is high - The AO signal is not enabled in this module - Power supply: 3.3-5V - Power consumption current 20 mA max - PCB dimensions: 32 x 14 mm Code S0038 Available Price €1.89
NDIR CO2 Sensor MH-Z14A Carbon dioxide detection MH-Z14A NDIR infrared gas module is a small size and common type sensor using the non-dispersive infrared (NDIR) principle to detect the existence of CO2 in air, with good selectivity, non-oxygen dependent and long lifetime. Code S0149 Available Regular price €29.95 -10% Price €26.96
GY-MAX4466 MAX4466 Electret Microphone Adjustable Amplifier Module The module is equipped with an electret microphone with a sensitivity in the range of 20-20 kHz and the amplification is used in the Maxim MAX4466 integrated circuit, an operational amplifier specially designed for use as a microphone preamplifier. Code M0214 Available Price €5.95
Hall Effect Sensor Module KY-003 with SH3144E TO-92 This module adapted for the arduino is a unipolar Ic Hall effect magnetic sensor. The Hall effect is when a current passes through a bar of semiconductor (or conductive) material, and if an induction magnetic field B is applied perpendicular to the direction of current flow, a voltage, called Hall voltage, proportional to the magnetic field, and the current appears on the faces sides of the bar. This tension is proportional to the displacement speed of the charge carriers, which is considerably higher in semiconductor materials than in metal conductors. Hall Effect Sensor Module KY-003 with SH3144E TO-92 features: - 3-pin connector: 1- GND 2- VCC 3- Voltage is recovered depending on the magnetic effect - Supply voltage: 5VDC - Output current: 40mA Code M0131 Available Price €1.69
DS18B20 Waterproof Digital Temperature Sensor Probe 3m Encapsulated with water resistant stainless steel with sensor dimensions 6 * 50mm, cable length 300 cm. DS18B20 Waterproof Digital Temperature Sensor Probe 3m features:- Based on the DS18B20 chip- Supply voltage: 3 ~ 5.5V- Consumption <5mA- Measuring Range: -55 ° C to 125 ° C- Accuracy: +/- 0,5ºC- Outputs: - GND black - Vcc red - Yellow digital output- Inocidable steel- Cable length: 3m Code S0008 Available Price €4.85
Digital Compass GY-273 Compas Magnetometer Three-axis electromagnetic field sensor module GY-273 including the HMC5883L chip that specifies the direction of the magnetic field of the ground. Digital Compass GY-273 Compas Magnetometer features: Supply voltage: 2.16 - 3.6 VDC, I2C interface with SCL, SDA, signals - Measurement range: 1.3 to 8 Gauss, Measurement resolution: 12 bits, Measurement accuracy: 0.73 - 4.35 Gauss, Transmission speed 400kHz, Sensitivity 230-1370 LSB / Gs, Output frequency: 75Hz, DRDY pin interruption, Dimensions of 18 mm x 13 mm. Code M0179 Available Price €3.79
Black UV sensor module UVM-30 for Arduino UVM-30A sensor module suitable for any location and requires stable and precise measurement of UV light. Ideal for Arduino projects. Black UV sensor module UVM-30 for Arduino features: - Operating voltage: 3-5 VDC, - Voltage input: DC 0-1 VDC, - 3-pin connector: - GND (-): ground connection, - Out: sensor output signal, - VCC (+): sensor supply, - Measurement accuracy: +/- 1UV index, - Working current: 0.06mA (standard) / 0.1mA (max.), - Response wavelength: 200-370 nm, - Working temperature: -20ºC - + 85ºC, - PCB size: 28x12mm. Code M0178 Available Price €9.95
Thermistor NTC 50.0K 5% MF52A epoxy resin coating resistor NTC thermistor - with a negative temperature coefficient, i.e. an increase in temperature causes a decrease in resistance. Thermistor NTC 50.0K 5% MF52A epoxy resin coating resistor features:Size: 3mmRated resistance: R25 = 50.0kB value 25/85 = 3950°KRated power: ‰¤ 50mWTolerance:± 5%Operating temperature: from -40°C to +125°C Tinned steel wire 25mm Code D0091 Available Price €0.49
HC-SR501 Motion Detector Module Passive Infrared PIR Sensor Arduino compatible IR motion detector with a detection range of 7 meters and an operating angle of 120º. An electric pyro sensor , which can detect infrared radiation levels - detect a change in the average IR levels of your detection zone. Ideal for projects with ARDUINO, PIC, AVR, STM32. HC-SR501 Motion Detector Module Passive Infrared PIR Sensor features: - Infrared sensor with control circuit - Adjustable sensitivity and time - Operating voltage: 4.5V- 20V - Consumption in Idle state: Code S0003 Available Price €1.79
SparkFun Weather Meter Kit The SparkFun weather meter kit is a set of basic mechanical components for building a weather station. This kit represents the three basic elements of weather measurement: wind speed, wind direction and precipitation. Whether you are a farmer, a professional meteorologist or a weather enthusiast, building your own weather station can be a truly rewarding project. However, when it comes to measuring the weather, you need some pretty specialised sensors. Code SP090 Backorder Price €109.90
Sensor Module FZ0888 IR Infrared Speed Meter Sensor Module FZ0888 IR Infrared Speed Meter features: - The FZ0888 encoder module is a device that can help you in the creation of your robotics and automation project, Whether you want to know the speed of a motor or its exact position - The module has a digital output (DO) which can be connected to your preferred microcontroller. The operating mode: - When the sensor is blocked, the DO output is high - The AO signal is not enabled in this module - Power supply: 3.3-5V - Power consumption current 20 mA max - PCB dimensions: 32 x 14 mm Code S0038 Available Price €1.89
NDIR CO2 Sensor MH-Z14A Carbon dioxide detection MH-Z14A NDIR infrared gas module is a small size and common type sensor using the non-dispersive infrared (NDIR) principle to detect the existence of CO2 in air, with good selectivity, non-oxygen dependent and long lifetime. Code S0149 Available Regular price €29.95 -10% Price €26.96
GY-MAX4466 MAX4466 Electret Microphone Adjustable Amplifier Module The module is equipped with an electret microphone with a sensitivity in the range of 20-20 kHz and the amplification is used in the Maxim MAX4466 integrated circuit, an operational amplifier specially designed for use as a microphone preamplifier. Code M0214 Available Price €5.95
Hall Effect Sensor Module KY-003 with SH3144E TO-92 This module adapted for the arduino is a unipolar Ic Hall effect magnetic sensor. The Hall effect is when a current passes through a bar of semiconductor (or conductive) material, and if an induction magnetic field B is applied perpendicular to the direction of current flow, a voltage, called Hall voltage, proportional to the magnetic field, and the current appears on the faces sides of the bar. This tension is proportional to the displacement speed of the charge carriers, which is considerably higher in semiconductor materials than in metal conductors. Hall Effect Sensor Module KY-003 with SH3144E TO-92 features: - 3-pin connector: 1- GND 2- VCC 3- Voltage is recovered depending on the magnetic effect - Supply voltage: 5VDC - Output current: 40mA Code M0131 Available Price €1.69
DS18B20 Waterproof Digital Temperature Sensor Probe 3m Encapsulated with water resistant stainless steel with sensor dimensions 6 * 50mm, cable length 300 cm. DS18B20 Waterproof Digital Temperature Sensor Probe 3m features:- Based on the DS18B20 chip- Supply voltage: 3 ~ 5.5V- Consumption <5mA- Measuring Range: -55 ° C to 125 ° C- Accuracy: +/- 0,5ºC- Outputs: - GND black - Vcc red - Yellow digital output- Inocidable steel- Cable length: 3m Code S0008 Available Price €4.85