Sensors

Photoresistance is a resistor whose resistance decreases as the intensity of the light that falls on it increases. 10x Photoresistor GL5539 LDR 50k - 100k features:
- Model: GL5539
- Spectral peak: 540nm
- Maximum DC voltage: 150V
- Maximum power: 100mW
- Resistance with light (10lux): 50-100KΩ
- Resistance with darkness (0lux): 5MΩ
- Response time: 20ms
- Operating temperature: -30ºC - 70ºC

Ideal for projects with ARDUINO.
You can use it with PIC, AVR, STM32.
It serves to measure the static acceleration, for example gravity, in applications where you need to measure the inclination.
Also to measure dynamic acceleration, movement. ADXL345 3-Axis Accelerometer SPI and I2C features:
- Type: 3-axis accelerometer
- Chip: ADXL345
- Supply voltage: 3-5V
- Consumption: 40uA active and 0.1uA on hold
- Communication: SPI and I2C
- Measurements: Static and dynamic acceleration
- Accelerometer scales ± 2g, ± 4g, ± 8g and ± 16g
- Resolution: 13 bits
- Dimensions: 20x16mm
- Operating temperature: -40 °C to +80 °C
- Detection: Free fall, click-double click

Compass is based on a QMC5883L system, which allows you to specify the direction of the earth's magnetic field. Digital Compass Magnetometer GY-271  features:

• 3.3V - 6V power supply voltage
• Current consumption of 100μA (standby 2uA)
• I2C interface
• Transmission speed 400kHz
• Sensitivity 230-1370 LSB / Gs
• Resolution 0.73-4.35mGs
• Frequency of 75Hz
• Measurement of the magnetic field in three axes of ± 8 Gauss with a resolution of 5 gauss miles

• Interruption DRDY pin
• Dimensions of 14 mm x 14 mm

Level sensor for liquids with float.
The liquid level sensor acts as a switch. The state is changed by means of a magnet located on the float. It can be used to detect liquid levels that are too high or too low.
Ideal for all those applications where it is necessary to control the level of non-corrosive liquids such as water tanks, aquariums.
Characteristic:
- Maximum Load: 50W
- Maximum Switching Voltage: 250V
- Maximum Switching Current: 0.5A
- Maximum charging current: 1A
- Operating temperature: -10ºC to + 60ºC
- Size: 58mm x 18mm

Support for ultrasounds, HC-SR04 distance meter.
Ideal to install the sensor on mobile platforms such as robots, vehicles, etc. Support for HC-SR04 Ultrasonic Sensor features:
- Material: Acrylic
- Color: transparent
- Includes screws

Sensor used to measure the current in the circuit to which it is connected.
It is based on the ACS712 chip, capable of measuring intensity in both DC and AC. Current Sensor ACS712 AC/DC 20A Hall Current Ammeter features:
- Output: Analog
- Power: 5V
- Accuracy: 1.5%
- Measuring capacity: +/- 20A
- Dimensions: 31 x 13 mm

It is very easy to make it work with an Arduino, PIC or any other microcontroller.
In its output pin we can measure the pulse width PWM depending on the distance of the obstacle.
Mounting bracket is ideal for installing the sensor on mobile platforms such as robots, vehicles, etc. HC-SR04 + Ultrasonic Sensor Support Arduino features:
- Supply voltage: 5V (4.5V-6V)
- Consumption: typical 30 mA, (35 mA max)
- Interface: VCC, GND, Signal
- Range: 2 cm to 3 meters
- Angle 15º
- LED measurement indicator in progress
- Frequency: 40 kHz for 200 μs
- Size: 30 mm x 20 mm Feature of the support: - Material: Acrylic
- Transparent color
- Includes screws

2x CNY70 Reflective Optical Sensor with Transistor Output features:
- Reflective optical sensor with transistor output
- Reflective optical coupler used to distinguish edge or line detection
- Dimensions of the housing are 7 x 7 x 6 mm
- Supply voltage: 5V
- Maximum diode current: 50 mA
- Maximum collector-emitter voltage: 32V
- Maximum collector current of 50 mA
- Quantity: 2 units

Also available with waterproof casing and 100cm cable and 200cm. DS18B20 Temperature Sensor TO-92 0.5ºC Precision 5V Integrated features:
- Device function: Temperature sensor
- Type of output: Digital
- Supply voltage: 3V to 5.5V
- Accuracy: ± 0.5ºC
- Temperature threshold: Programmable
- Operating temperature: -55ºC to + 125ºC
- Encapsulated: TO-92
- Supply current: 1.5mA

Sensor Module FZ0888 IR Infrared Speed Meter features:
- The FZ0888 encoder module is a device that can help you in the creation of your robotics and automation project, Whether you want to know the speed of a motor or its exact position
- The module has a digital output (DO) which can be connected to your preferred microcontroller.
The operating mode:
- When the sensor is blocked, the DO output is high
- The AO signal is not enabled in this module
- Power supply: 3.3-5V
- Power consumption current 20 mA max
- PCB dimensions: 32 x 14 mm

Precision Temperature Sensor TO-92 LM335 LM335Z-ST features:
- Power supply from 5 to 30 Vdc
- Connection through analog input
- Temperature range from -40ºC to 100ºC
- Linearity +10 mV / ºK
- Accuracy of measurement: ± 2 ° C
- Manufacturer: Texas Instruments

Sensor TCRT5000 Infrared IR Tracker Line Obstacle Phototransistor features:
- Operating range: 0.2mm to 15mm
- Receiver: Phototransistor
- Emitter: Infrared Led
- Wavelength: 950 nm

Encapsulated with water resistant stainless steel with sensor dimensions 5.5*50mm, cable length 200 cm. DS18B20 Probe 2m Submersible Temperature Sensor features:
- Based on the DS18B20 chip
- Supply voltage: 3 ~ 5.5V
- Consumption <5mA
- Measuring Range: -55 °C to 125 °C
- Accuracy: +/- 0,5ºC
- Outputs: - GND black
      - Vcc red
      - Yellow digital output
- Inocidable steel
- Cable length: 2m  

LM35 Temperature Sensor LM35DZ TO92 features:
- The output is linear and each degree Celsius equals 10 mV
- Power supply from 4 to 30 Vdc
- Connection through analog input
- Temperature range from 0ºC to 100ºC
- Linearity +10 mV / ºC
- Quantity: 1 unit

Sound detection module for Arduino projects, smart cars. Analogical Acoustic Sensor 4-Pin Microphone Sound Detector Module features:
- Adjustable High Sensitivity Acoustic Sensor
- LM393 comparator chip
- Integrated indicator LED
- AO analog output, output voltage signal in time real microphone
- DO digital output, sensitivity adjustable through potentiometer
- Frequency Range between 30 and 15000 Hz
- Power 4 ~ 6V
- Measurements 36x16x15mm

5.8GHz Doppler Radar Motion Sensor features:
- Microwave motion detector module
- The main applications can be security alarms and sensors, Automatic door systems, ATM machines, car reverse systems, light sensors, can also be used for traffic monitoring and monitoring applications.
- High resistance to radio-frequency interference
- Frequency: 5.8GHz
- Operating Voltage: 3.3V - 20V TTL 3.3V
- Standby Current: 3mA
- Detection Range: 3-8 meters, 360 degrees
- Power of Output: 2mW
- Dimensions: 32x23 mm
- R6 - time-delay; initial value 2.2k - 1s, without delay resistance 30s, can be adjusted up to 250k
- R9 - for sensitivity adjustment

Sensor used to measure the current in the circuit to which it is connected. Characteristic: - Output: Analog
- Power: 5V
- Accuracy: 1.5%
- Measuring capacity: +/- 30A
- Dimensions: 31 x 13 mm

The humidity sensor DHT11 comes in a plastic body ideal for mounting on a panel or similar. It uses a capacitive sensor that returns a digital signal with the measurement. DHT11 Temperature and Humidity Sensor features:
- Operating voltage: 3 to 5 VDC
- Humidity measurement range: 20-95% ± 5% accuracy
- Temperature measurement range: 0ºC to 50ºC ± 2º accuracy
- Maximum sampling rate: 2 seconds
- Working current 2.5mA
- Iterfaz 1-wire
- Dimensions: 2.3 x1.2x 0.5cm
- Quantity: 1 unit

- The DHT22 humidity sensor is presented in a plastic body ideal for mounting on a panel or similar. It uses a capacitive sensor that returns a digital signal with the measurement - This sensor, unlike DHT11, is capable of measuring negative temperature values ​​and measures tenths of a degree
Characteristic:
- Operating voltage: 3 to 5.5 VDC - Humidity measurement range: 0-100% ± 2% accuracy
- Temperature measurement range: -40ºC to 80ºC ± 0.5º accuracy
- Maximum sampling rate: 2 seconds
Useful links for Arduino / Raspberry programming and projects with Arduino / Raspberry boards:
Write texts on the OLED 0.96 '' screen
- Read the measurements of the temperature / humidity sensor DHT22 / AM2302 on a 0.96 '' OLED screen
Send />

M12 Inductive Proximity Sensor PNP DC 6-36V LJ12A3-4-Z/BY 3D Printer features:
- This sensor can be configured as auto Z axis level
- Sensor detection switch inductive proximity LJ12A3-4-Z / BY
- PNP DC6-36V
- Often used for 3D printer bed leveling
- Typical application: printer bed level sensor 3D
- Cylindrical cable type DC 3 cable type (black, brown, blue)
- Inductive sensor type
- PNP NO (Normal Open)
- Detecting Distance 4mm - DC supply voltage 6-36V
- Current output 300mA
- Response frequency 0.5KHz
- Detects iron / aluminum
- Operating temperature -25 ° C at + 55 ° C (Non-freezing condition)
- Head diameter 12 mm
- Size 6.2 x 2cm
- Cable length 100cm

Ideal for projects with ARDUINO, Smart Car. Sensor Module Infrared Obstacle Detector Car Robot features:
- Power supply: 3.3 - 5V DC
- OUT level 0/1 output
- Sensitivity adjustment
- Power LED
- Distance from detection: 2 - 30cm (max60cm)
- detection angle: 35º
- LED output status indicator
- Dimensions: 40x13x8mm

MQ-2 Gas and Smoke Module Sensor Detector Methane Propane Butane LPG features:
- Main chip: MQ-2 flammable gas and smoke sensor and comparator LM393
- Working voltage: 5V
- Current: 150mA
- Digital output: TTL 0/1
- Analog output: analog voltage sensing value
- Quick response features:
- Concentration detection:
  200ppm - 5000ppm LPG, propane
  300ppm - 5000ppm butane
  5000ppm - 20000ppm methane
  300ppm - 5000ppm H2
  100ppm -2000ppm alcohol
- Adjustable sensitivity with the potentiometer
- Size: 32mm x 20mmx 18mm

MQ-4 Gas Methane Sensor Module for Arduino features:
- Main chip: MQ-4 methane sensor and comparator LM393
- Working voltage: 5V
- Current: 150mA
- Digital output: TTL 0/1
- Analog output: analog voltage sensing value
- Quick response features:
- Detection concentration:
200ppm- 10000ppm CH4, natural gas
- Adjustable sensitivity with the potentiometer
- Size: 32mm x 20mmx 18mm

MG-5 Gas Methane Sensor Module for Arduino features:
- Main chip: MQ-5 natural gas sensor and comparator LM393
- Working voltage: 5V
- Current: 150mA
- Digital output: TTL 0/1
- Analog output: analog voltage sensing value
- Quick response features:
- Detection concentration:
- 200ppm - 10000ppm LPG, LNG, natural gas, propane,
- Adjustable sensitivity with the potentiometer
- Size: 32mm x 20mmx 18mm

Ideal for projects with ARDUINO.
You can use it with PIC, AVR, STM32. MPU-6050 Accelerometer Module + Gyroscope 3 features:
- Chip: MPU-6050
- Power supply: 3V-5V
- Operating current: 5mA
- Communication: I2C
- 16-bit analog-digital converter on all axes
- Gyroscope scales: ± 250, ± 500, ± 1000 and ± 2000 ° / sec (dps) (programmable by the user)
- Accelerometer scales: ± 2g, ± 4g, ± 8g and ± 16g (programmable by the user)
- Dimensions: 14 x 21 x 1.3mm
- Quantity: 1 unit (1 strip of 8 pin + 1 strip of 8 layered pin)

The module has two outputs: analog A0 and digital D0.
digital output D0 - signal 0 or 1 appears depending on the configuration of threshold.
The threshold is fixed with the potentiometer. Characteristic: - Operating voltage: 3.3V -5 V - Sensitivity adjustable by potentiometer
- Dual output mode: analog and digital
- Red LED - power indicator
- Green LED - digital switching output indicator
- Measurements PCB: 3 x 1.5 cm
- Sensor measurements: 5.4 x 3.9 cm

Easily convert water level to analog signal
The analog output signal can be read directly on the Arduino board
Characteristic:
- Operating voltage: 3.3V -5 V
- Consumption: less than 20 mA - Sensor type: Analog
- Operating temperature: 10º C -30º C
- Detection area: 40 mm x 16 mm
- Dimensions: 60 mm x 20 mm

The DHT11 humidity sensor is presented in a plastic body ideal for mounting on a panel or similar. It uses a capacitive sensor that returns a digital signal with the measurement.
Characteristic:
- Operating voltage: 3 to 5 VDC - Humidity measurement range: 20-95% ± 5% accuracy
- Temperature measurement range: 0ºC to 50ºC ± 2º accuracy
- Maximum sampling rate: 2 seconds - Working current 2.5mA
- 1-wire interface
- Dimensions: 32 x14 mm
- Quantity: 1 unit with 3x female / female cables

Microwave motion detector module.
The main applications may be security alarms and sensors, systems Automatic doors, ATM machines, car reverse systems, light sensors, can also be used for traffic monitoring and control applications.
High resistance to radio frequency interference.
Characteristic:
- Frequency: 10.525GHz
- Frequency Accuracy: 3MHz
- Minimum Output: 13dBm EIRP
- Operating Voltage: 5V ± 0.25V
- Operating current (CW): 60mA maximum, 37mA typical
- Harmonic emissions: -10dBm
- Detection Range: Over 20 meters
- Power of Output: 5mW
The device is sensitive to electrostatic discharge and can be damaged during welding.
The IF output is particularly sensitive.

High sensitivity to Ammonia (NH3), Nitrogen oxides (NOx), Alcohol, Sulphides, Benzene (C6H6), CO2, smoke and other harmful gases.  The MQ-135 sensor is to sensible for other gasses in the air so that is not possible to get good values for CO2 from it.
MQ-135 Air Quality Sensor features:
- Main chip: MQ-135 natural gas sensor and comparator LM393
- Working voltage: 5V
- Current: 150mA
- Digital output: TTL 0/1
- Analog output: analog voltage sensing value
- Quick response features:
- Detection concentration:
   10ppm - 300ppm NH3
   10ppm - 1000ppm Benzene
   10ppm - 300ppm Alcohol
- Adjustable sensitivity with the potentiometer
- Size: 32mm x 20mmx 18mm

MQ-9 Carbon Monoxide Sensor Module features:
- Main chip: MQ-9 methane sensor and comparator LM393
- Working voltage: 5V
- Current: 150mA
- Digital output: TTL 0/1
- Analog output: analog voltage sensing value
- Quick response features:
- Detection concentration:
   20ppm- 2000ppm carbon monoxide
   500ppm- 10000ppm methane CH4
   500ppm- 10000ppm LPG
- Adjustable sensitivity with the potentiometer
- Size: 32mm x 20mmx 18mm

MQ-8 Hydrogen Gas Sensor Module features:
- Main chip: MQ-8 methane sensor and comparator LM393
- Working voltage: 5V
- Current: 150mA
- Digital output: TTL 0/1
- Analog output: analog voltage sensing value
- Quick response features:
- Detection concentration:
  100ppm- 10000ppm hydrogen H2
- Adjustable sensitivity with the potentiometer
- Size: 32mm x 20mmx 18mm

MQ-6 Gas Methane Sensor Module for Arduino features:
- Main chip: MQ-6 methane sensor and comparator LM393
- Working voltage: 5V
- Current: 150mA
- Digital output: TTL 0/1
- Analog output: analog voltage sensing value
- Quick response features:
- Detection concentration:
- 200ppm- 10000ppm LPG, LNG
- Adjustable sensitivity with the potentiometer
- Size: 32mm x 20mmx 18mm

Sensor Module GUVA-S12SD UV features:
- The module based on the Schottky-type photodiode - applicable to the optical mode
- This is a " true "UV sensor instead of calibrated light sensor
- It has high sensitivity, high stability, good linearity
- Power supply: 2.5V - 5V
- Analog output
- Captured wavelength: 240-370nm
- Ultra low power consumption
- Meteorological applications, skin care, industrial UV level measurement
- PCB dimensions: 11x27mm

Capsule Electret Condenser Microphones 9.5 MIC features:
- Measures: 9.7 x 6.7mm
- Impedance: 1.5kΩ
- Working current: 0.5mA
- Working voltage: 4.5V (1.5-10V)
- Bandwidth: 50 ... 16000Hz
- Signal to noise ratio: ‰¥58dB
- Sensitivity: -42 ± 3dB
- Sensitivity tolerance: ± 3dB
- Distance between terminals: 2.54mm

Sound detection module for Arduino projects, smart cars.
Sound Detection Sensor Module features:
- Adjustable High Sensitivity Acoustic Sensor
- Chip LM393
- Red LED indicator integrated
- Frequency range between 30 and 15000 Hz
- Power 4 ~ 6V
- Measures 32x16x10mm

Arduino compatible IR motion detector with a detection range of 3 meters.
One sensor electric pyro, which can detect infrared radiation levels - detect a change in the average IR levels of your detection zone.
Ideal for projects with ARDUINO, PIC, AVR, STM32.
Characteristic:
- Operating voltage: 4.5V- 20V
- Consumption in idle state:

Detects changes in the sensor angle and returns to the digital value. 5x SW-520D Vibration Metal Tilt Sensor features:
- Contact resistance:

The meter built on the basis of a water rotor and a Hall effect sensor
Please note this is not a Accuracy. Pulse rate varies slightly depending on flow rate, fluid pressure, and sensor orientation. Water Flow Sensor 1-30l /Min YF-S201 features:
- Working voltage range: DC 5 ~ 18 V
- Allow pressure: water pressure below 1.75Mpa
- Accuracy (flow-pulse output): ± 1 ~ 30 l / min
- Use temperature: ‰ ¤ 80 ° C
- Load capacity: ‰ ¤ 10 mA (5Vdc)
- Operating humidity: 35% ~ 90% RH (frost free)
- Temperature: -25 ~ + 80 ° C
- Outlet diameter: 1/2 "
- Red wire: positive supply
- Wire Black: negative power supply
- Yellow Cable: signal output
- Color: black
- Size: 6.2x3.6x3.4 cm

The optical module (reflective) sensor with CMOS Schmitt inverter 74HC14D, which detects obstacles with high precision. The ideal obstacle detection detector for the installation of smart robots. TCRT5000 - reflective optical sensor that has a compact construction where the light emitter and receiver are placed in the same direction to detect the presence of an object using infrared reflection on the object. The working wavelength is 950nm. The transmitter is infrared LED and the phototransistor receiver.
The sensor allows the detection of an object at a distance of up to 15 mm. TCRT5000 IR Infrared Sensor Module features:
- The module has an output: digital
- CMOS Schmitt inverter 74HC14D
- Power supply: 5V - Range: 0.2 mm - 15 mm

The module uses a 24-bit high precision A/D conversion chip HX711.
The input circuit can be configured to provide a bridge.
The electric bridge voltage sensor model (such as pressure, weight) is an ideal sampling module with high precision and low cost. HX711 Module Weighing Pressure Sensor 24 Bits features:
- Two selectable differential input channels
- Active low noise PGA with selectable gain of 32, 64 and 128
- Power supply regulator for load cell and ADC analog power supply
- Oscillator on chip that does not require external component with optional external glass
- Power-on-reset on the chip
- Simple serial control and serial interface: controls driven by pins, programming is not required
- Output data rate 10SPS or 80SPS selectable

Load Cell 1 kg Scale Sensor Weight Arduino 
Load cell to measure weight up to 1kg
The transducer measures the deformation of the metal structure and converts it into a few mV. Load cell Load Cell Weight Sensor 1kg features:
- Load range: 1kg
- Operating voltage: 3VDC ~ 14 VDC.
- Nominal output: 1.0 ± 0.15mV / V
- Repeatability: 0.03% FS
- Effect of the temperature at the outlet: 0.01% F.S / ° C

Load cell Load Cell Weight Sensor 2kg features:
- Load cell to measure weight up to 2kg
- The transducer measures the deformation of the metal structure and converts it into a few mV
- Load range: 2kg
- Operating voltage: 3VDC ~ 14 VDC
- Nominal output: 1.0 ± 0.15mV / V
- Repeatability: 0.03% FS
- Effect of the temperature at the outlet: 0.01% F.S / °C
- Effect of temperature on zero: 0.05% F.S / °C
- Zero: ± 0.1000 mV / V
- Input impedance: 1115 + -10% Ω
- Output impedance: 1000 + - 10% Ω
- Insulation resistance:> = 1000 MΩ
- Safe Overload Rate: 150% FS
- Final overload rate: 200% FS
- Temperature range: -20 - 60 °C
- Material: Aluminum alloy
- Degree of protection: IP65

Load cell Load Cell Weight Sensor 5kg features:
- Load cell to measure weight up to 5kg
- The transducer measures the deformation of the metal structure and converts it into a few mV
- Load range: 5kg
- Operating voltage: 3VDC ~ 14 VDC
- Nominal output: 1.0 ± 0.15mV / V
- Repeatability: 0.03% FS
- Effect of the temperature at the outlet: 0.01% F.S / °C
- Effect of temperature on zero: 0.05% F.S / °C
- Zero: ± 0.1000 mV / V
- Input impedance: 1115 + -10% Ω
- Output impedance: 1000 + - 10% Ω
- Insulation resistance:> = 1000 MΩ
- Safe Overload Rate: 150% FS
- Final overload rate: 200% FS
- Temperature range: -20 - 60 °C
- Material: Aluminum alloy
- Degree of protection: IP65

Load cell Load Cell Weight Sensor 10kg features:

Load range: 10kg

Operating voltage: 3VDC ~ 14 VDC.

Rated output: 1.0 ± 0.15mV/V.

Repeatability: 0.03% FS

Effect of temperature on output: 0.01% F.S / ° C

Temperature effect on zero: 0.05% F.S / ° C

Load cell Load Cell 20kg features:
- Load range: 20kg
- Operating voltage: 3VDC ~ 14 VDC
- Nominal output: 1.0 ± 0.15mV / V
- Repeatability: 0.03% FS
- Effect of the temperature at the outlet: 0.01% F.S /°C
- Effect of temperature on zero: 0.05% F.S /°C
- Zero: ± 0.1000 mV / V
- Input impedance: 1115 + -10% Ω
- Output impedance: 1000 + - 10% Ω
- Insulation resistance:> = 1000 MΩ
- Safe Overload Rate: 150% FS
- Final overload rate: 200% FS
- Temperature range: -20 - 60 °C
- Material: Aluminum alloy
- Degree of protection: IP65
- Cable length: 25 cm
- Size: 75 x 12.7 x 12.7 mm
- Wiring:
* Red: Feeding +
* Black: Source -
* Green: Sign +
* White: Signal -

Photoresistor is a resistor whose resistance decreases with increasing intensity of light
that affects her 10x Photoresistor GL5528 LDR features:
- Model: GL5528
- Spectral peak: 540nm
- Maximum DC voltage: 150V
- Maximum power: 100mW
- Resistance with light (10lux): 10-20KΩ
- Resistance with darkness (0lux): 1MΩ
- Response time: 20ms
- Operating temperature: -30ºC - 70ºC
- 10k - 20k Arduino PiC 5mm
- Quantity: 10 units

This Reed switch module uses a small device called a reed switch.
When the device is exposed to a magnetic field, the two ferrous materials inside the switch come together and the switch closes. When the magnetic field is removed the switch opens. The operating mode: - When exposed to a magnetic field the DO output is high
- Power supply: 3.3-5V
- Contact type: SPST-NO (normally open)
- Use temperature: -20ºC to + 80ºC
- Type Output: Digital (1 - 0)
- PCB dimensions: 32 x 14 mm

This module includes the BMP280 component that converts atmospheric pressure, temperature and humidity with high precision into a digital signal.
The equipment uses the two I2C and SPI interfaces. The very good measurements made by the BMP280 allows the module to be used as an altimeter.
Its 5-pin straight connector allows easy connection to other electronic boards. BMP280 Temperature Barometric Pressure Sensor Module/SPI features:
- Interfaces:
       -I2C (up to 3.4 MHz)
       -SPI (up to 10 MHz)
- Supply voltage: 1.8-5VDC
- Module operating range:
       - Temperature: -40ºC to + 85ºC
0-100%
       - Pressure: 300-1100 hPa
- Resolution of the measures:
       - Temperature: 0.01ºC

This module is a dust sensor capable of detecting more than one micron of dust particles.
It has two types of output: output of 4V high-level signal for a clean environment and 0.7V low-level signal for a particle-laden environment.
Its power supply is 5VDC and the particle detection range is maximum at 8000 units per 283ml. Dust Sensor Module PPD42NS PM2.5 features:
- Supply voltage: 5VDC
- Working current: 90mA
- Sensitivity: 0.5V / ( 0.1 mg / m3)
- Particle detection minimum value: 1 micron
- Output mode: Hi = 4V impulses (clean environment); Lo = 0.7V (charged environment)
- Temperature working: 0-45 ° C
- Working humidity: 0-90% RH
- PCB size: 59x45x22 mm

This module adapted for the arduino is a light sensor. The resistance of the LDR cell decreases as the light intensity increases.
On the contrary in a dark environment, the resistance of the LDR cell increases accordingly. Characteristic: - 3-pin connector: 1- GND
2- VCC
3- analog output - the voltage depending on the light
- Supply voltage: 3.3 V-5VDC
- PCB size: 19x15x8 mm

The module is based on a touch sensitive IC capacitive touch switch module (TTP223B).
In the normal state, the module produces Low power consumption. When a finger touches the corresponding position, the module output is high, if not touched for 12 seconds, it switches to low power mode. Digital Touch Sensor B21 features:
- Low power consumption
- Input voltage: 2 - 5.5VDC
- Can replace the traditional touch of a button - Four M2 screws diameter 2.2 mm that position the holes for easy installation
- 3-pin control interface:
1- GND
2- VCC
3- Control signal (output pin)
- Power indicators: Bright green LED when the sensor is on

Definition of the Hall effect: When a current passes through a bar of semiconductor (or conductive) material, and if an induction magnetic field B is applied perpendicularly to the direction of current flow, a voltage, called the Hall voltage, proportional to the magnetic field, and the current appears on the side faces of the bar.
This voltage is proportional to the speed of movement of the charge carriers, It is considerably higher in semiconductor materials than in metal conductors. Magnetic Sensor Characteristic: - Input Voltage: 3.8-30VDC - Output current: 40mA
High output current capacity -40 mA maximum absolute
Quad-Hall design virtually eliminates static mechanical effects
Magnetic compensated temperature - Digital current sinking output

This module adapted for the arduino is a unipolar Ic Hall effect magnetic sensor. The Hall effect is when a current passes through a bar of semiconductor (or conductive) material, and if an induction magnetic field B is applied perpendicular to the direction of current flow, a voltage, called Hall voltage, proportional to the magnetic field, and the current appears on the faces sides of the bar. This tension is proportional to the displacement speed of the charge carriers, which is considerably higher in semiconductor materials than in metal conductors. Hall Effect Sensor Module KY-003 with SH3144E TO-92 features:
- 3-pin connector: 1- GND
2- VCC
3- Voltage is recovered depending on the magnetic effect
- Supply voltage: 5VDC
- Output current: 40mA

Ultrasonic sensors overcome many of the weaknesses of IR sensors by providing distance measurement regardless of the color and illumination of obstacles. Ultrasound Distance Sensor HC-SR05 features:
- Power supply: 4.5-5.5 VDC
- Supply current: 10 to 40 mA
- Activation pin format: 10 μs digital pulse
- Echo Pin Output: 0-Vcc
- Echo Pin Format: the output is DIGITAL and directly proportional with range. See our conversion formula below
- Measurement range: 2cm to ~ 4.5m
- Measurement resolution: 0.3cm
- Measurement angle: up to 15 degrees
- Measurement speed: 40 Hz,
- Connector: standard 5-pin male connector that can be connected directly to boards or breadboards:
- 1: VCC
- 2: Trig
- 3: Echo

The MAX9812 is a sound amplifier specially designed to treat the signal coming from microphones.
We can use it together with Arduino to measure sound from a processor like Arduino.
When we saw the modules with microphone we commented that, in general, the signal generated is too low to be registered correctly.
If we want to be able to measure sounds, we will have to amplify the signal. The MAX9812L has single / dual inputs, fixed gain of 20dB, bandwidth of 400 kHz, low noise and low signal distortion 0.015% THD.
There are two models, its supply voltage is 2.7V to 3.6V.
We can use the sensors with MAX9812 for applications that require measuring the intensity or frequency of the sound.

It consists of three principles of induction of primary colors, if you know the composition of all types of color values, you can know the color of the test object.
For TCS230, a color filter is chosen, only a certain primary pass is allowed, it is stopped by another color. For example, when choosing a red filter, the incident light can only be stopped in red, blue and green, so you can get the intensity of the red beam of light.
For the same reason, the choice of other filters, can obtain the intensity of blue light and green light.
Through these three values, the color of the light can be projected onto a TCS230 sensor. Color Recognition Sensor GY-31 TCS230 TCS3200 features:
- Operating voltage: 3 - 5 VDC
- Model GY-91
- Chip TCS230 TCS3200

This photo-resistance module is very sensitive to ambient light. Activation of the microcontroller or retransmission modules,
The brightness module of the ambient light reach the set threshold, the output is high when the ambient light exceeds the set threshold.
The DO output can be connected directly to a microcontroller to detect the light environment and create a light control switch.
It has a speed range of 0% to 100%. Digital Light Intensity Sensor with Photo Resistance with LM393 Controller features:
- Operating voltage: 3.3 - 5 V
- Input current: 50 mA
- Use a very sensitive photo resistance
- Use a LM393 wide voltage comparator, high quality output signal
- Adjustable potentiometer can regulate the brightness of detected light

The DS18B20 is a digital temperature sensor from Dallas Semi Conductors, used to measure ambient temperature or to carry out tests. It supports multipoint readings of the mesh networking type, being able to be deployed in three lines, in order to achieve these readings, it has a built-in pull-up resistance. Dallas Temperature Sensor Module DS18B20 features:
- Operating voltage: 3 - 5.5 VDC
- Measurement operating temperature: -55 ° C - 125 ° C
- Output current: 5 μA
- Accuracy of ± 0.5 ° C between -10 ° C and + 85 ° C
- Storage temperature: -55 ° C - + 125 ° C
- 100% new and high quality
- Module DS18B20 temperature measurement sensor
- The DS18B20 sensor has a pull-up resistor
- Power indicator LED on the module

M12 Inductive Proximity Sensor NPN DC 6-36V LJ12A3-4-Z/BX 3D Printer features:
- This sensor can be configured as Z axis auto level
- Inductive proximity sensor detection switch LJ12A3-4-Z / BX
- NPN DC6-36V
- Often used for 3D printer bed leveling
- Typical application: 3D printer bed level sensor
- Type of Cylindrical DC cable 3 type of cable (black, brown, blue)
- Inductive sensor type
- NPN NO (Normal Open)
- Detecting Distance 4mm
- DC supply voltage 6-36V
- 300mA current output
- 0.5KHz response frequency
- Detects iron / aluminum
- Operating temperature -25 ° C to + 55 ° C (Condition non-freezing)
- Head diameter 12 mm
- Size 6.2 x 2cm
- Cable length 100cm