Sensor Module Moisture Earth Water Soil The module has two outputs: analog A0 and digital D0 Digital output D0 - signal 0 appears or 1 depending on the threshold setting The threshold is set with the potentiometer The sensor can be used for example: Automatic watering for potted plants With this module you will be able to measure the humidity of the soil, so that you will be able to control the humidity level of the soil of your plants Characteristic: Operation: 3.3V -5V - Sensitivity adjustable by potentiometer - Dual output mode: analog and digital - Red LED - power indicator - Green LED - indicator digital switching output - PCB measurements: 3 x 1.5 cm - Probe measurements: 6 x 3 cm Code S0021 Available Price €1.61
Resistor 10K Ohm 5% 0,25W 1/4W Resistor 10K Ohm 5% 0,25W 1/4W features:-10K Ohm-Type: Carbon film-Tolerance: ±5%-Power: 0.25W-Dimensions: 2x7mm Code D0021 Available Price €0.07
Nano plate V3.0 CH340 + Arduino compatible pins It has an ATMega328P chip running at 16Mhz with a factory loaded bootloader Characteristic: - Microcontroller: ATmega328 - Operating Voltage (logic level): 5V - Input Voltage (recommended): 7-12V - Digital I / O Pins: 14 (6 PWM outputs) - Analog Inputs: 8 (A0-A7) - DC Current per Pin I / O 40 mA - Flash Memory: 32 KB (2 KB used by the bootloader) - SRAM: 2 KB - EEPROM: 1 KB - Clock Frequency: 16 MHz - USB Communication - CH340 - Dimensions: 18 mm x 44 mm Code B0026 Available Price €8.26
Strip Macho 80 Pins Doble 2x40 Right Angle Connector with 80pins in double rows 2x40, ready to break and with 90 ° angle for vertical use. Code K0115 Available Price €0.79
DC Step-Down Converter 5A 4-38v to 1.25-36v XL4015 LED LiPo Descent module.Use a multimeter to check the output voltage and adjust the potentiometer.Control of voltage and current.DC Step-Down Converter 5A 4-38v to 1.25-36v XL4015 LED LiPo features:- Input voltage: 4-38V- Output voltage: 1.25-36V- Current output: adjustable, 4.5A (max 5A)- Output power: 75W maximum- Operating temperature: -40 to + 85 ºC- Operating frequency: 180KHz- Efficiency conversion: up to 96%- Short circuit protection: Yes (limited current 8A)- Protection over temperature: the output switches off automatically- Size: 62mm x 26mm x 14mmPrincipal functions:- Step-down converter with overcurrent protection- Li-Po battery charger, Li-Ion Code A0014 Available Price €2.88
5x Electrolytic Capacitor 2200uF 25V 105ºC PIC for Arduino 5x Electrolytic Capacitor 2200uF 25V 105ºC PIC Arduino features:-Type: Electrolytic Capacitor-Assembly: intern-Value: 2200uF-Maximum tension: 25V-Maximum temperature 105º C-Dimensions: 13x21mm-Quantity: 5 units Code D0049 Available Price €0.23
Kit 37 Sensors in a Box for Arduino The perfect Arduino sensor kit to start learning about the world of electronics with Arduino. It comes with our step-by-step guide to each sensor, as well as its libraries. Code B0040 Available Price €16.11
Low power Bluetooth / Multi-standard SensorTag CC2650STK TI The new SensorTag IoT kit invites you to realize your product idea connected to the cloud. The new SensorTag now includes 10 low-power MEMS sensors in a small red package. And it's expandable with DevPacks to make it easy to add your own sensors or actuators. Connect to the cloud with low-power Bluetooth and Get your sensor data online in 3 minutes. The SensorTag is ready to go right away with an iOS and Android app, no programming experience to get started. The new SensorTag is based on The CC2650 Wireless MCU, which offers 75% less power consumption than previous Bluetooth low energy products. This allows the SensorTag to run on batteries, and offers years of battery life with a single coin cell battery. Code W0088 Backorder Price €37.19
Magnetic sensor switch for windows/doors 14X27mm adhesive This sensor behaves like a switch that closes the circuit when both parts are put together. Ideal for intrusion detection, alarm system, light control and opening and closing devices. Code K0275 Backorder Price €1.64
Magnetic sensor switch for windows/doors 14X27mm screw mounting This sensor behaves like a switch that closes the circuit when both parts are put together. Ideal for intrusion detection, alarm system, light control and opening and closing devices. Code K0337 Available Price €1.89
Low power Bluetooth / Multi-standard SensorTag CC2650STK TI The new SensorTag IoT kit invites you to realize your product idea connected to the cloud. The new SensorTag now includes 10 low-power MEMS sensors in a small red package. And it's expandable with DevPacks to make it easy to add your own sensors or actuators. Connect to the cloud with low-power Bluetooth and Get your sensor data online in 3 minutes. The SensorTag is ready to go right away with an iOS and Android app, no programming experience to get started. The new SensorTag is based on The CC2650 Wireless MCU, which offers 75% less power consumption than previous Bluetooth low energy products. This allows the SensorTag to run on batteries, and offers years of battery life with a single coin cell battery. Code W0088 Backorder Price €37.19
Magnetic sensor switch for windows/doors 14X27mm adhesive This sensor behaves like a switch that closes the circuit when both parts are put together. Ideal for intrusion detection, alarm system, light control and opening and closing devices. Code K0275 Backorder Price €1.64
Magnetic sensor switch for windows/doors 14X27mm screw mounting This sensor behaves like a switch that closes the circuit when both parts are put together. Ideal for intrusion detection, alarm system, light control and opening and closing devices. Code K0337 Available Price €1.89