LDR Module Motor Resistance KY-018

Photoresistance is a resistor whose resistance decreases as the intensity of the light that falls on it increases. 10x Photoresistor GL5539 LDR 50k - 100k features:
- Model: GL5539
- Spectral peak: 540nm
- Maximum DC voltage: 150V
- Maximum power: 100mW
- Resistance with light (10lux): 50-100KΩ
- Resistance with darkness (0lux): 5MΩ
- Response time: 20ms
- Operating temperature: -30ºC - 70ºC

Ultraviolet ray detection module 200-370nm with a supply voltage of 3.3-5 VDC and a very low consumption of 0.1mA.
100% compatible UNO module.
Characteristic:
- Operating voltage: 3.3-5 VDC
- Output voltage: 0-1 VDC
- 3-pin connector:
- OUT: output signal
- VCC: Supply voltage
- GND: Ground connection - Test accuracy: ± 1UV INDEX
- Current: 0.06mA (typical), 0.1mA (maximum)
- Wavelength of the response: 200nm-370nm (ultraviolet rays) - Response time: less than 0.5 seconds
- Operating temperature: -20ºC - + 85ºC
- Size: 19.80 x 15mm

10x Photoresistor 5mm GL5516 LDR 5-10k for Arduino.
Photoresistor is a resistor whose resistance decreases when increasing the intensity of the light that falls on it. 10x Photoresistor GL5516 LDR features:
- Model: GL5516
- Spectral peak: 540nm
- Maximum DC voltage: 150V
- Maximum power: 90mW.
- Resistance with light (10lux): 5-10KΩ
- Resistance with darkness (0lux): 0.5MΩ
- Response time: 20ms
- Operating temperature: -30ºC - 70ºC

Sensor Module ML8511 UV features:
- The module converts the photocurrent into voltage to detect UV intensity
- The analog voltage is proportional to UV light detecting
- The has a power saving mode of up to 0.1uA, suitable for smart portable devices or mobile phones for use
- Power supply: 5V
- Analog output
- Captured wavelength: 280-390nm
- Ultra low power consumption
- Meteorological applications, skincare, industrial UV level measurement
- Dimensions of PCB: 30x22mm

Descripción: Light sensor module to measure light intensity and obtain digital data from it.
Ideal for projects with ARDUINO.
You can use it with PIC, AVR, STM32.
BH1750FVI (Rohm) is used to adjust backlighting of LCD screens and keyboards by manufacturers of mobile phones, digital cameras, navigation and portable gaming devices. Light Sensor Module BH1750 FVI Arduino Raspberry features:
- Chip BH1750FVI
- Supply voltage 3V-5V
- Integrated 16bit AD converter
- Detection range: 0-65535 lx (with an accuracy of 1 lux)
- Interface: II2C
- Low dependence on the light source (eg incandescent lamp, fluorescent lamp, halogen lamp, white LED, sunlight)
- Dimensions 18.4 x 14 mm

Photoresistor is a resistor whose resistance decreases with increasing intensity of light
that affects her 10x Photoresistor GL5528 LDR features:
- Model: GL5528
- Spectral peak: 540nm
- Maximum DC voltage: 150V
- Maximum power: 100mW
- Resistance with light (10lux): 10-20KΩ
- Resistance with darkness (0lux): 1MΩ
- Response time: 20ms
- Operating temperature: -30ºC - 70ºC
- 10k - 20k Arduino PiC 5mm
- Quantity: 10 units

UVM-30A sensor module suitable for any location and requires stable and precise measurement of UV light.
Ideal for Arduino projects.
Black UV sensor module UVM-30 for Arduino features:
- Operating voltage: 3-5 VDC,
- Voltage input: DC 0-1 VDC,
- 3-pin connector:
- GND (-): ground connection,
- Out: sensor output signal,
- VCC (+): sensor supply,
- Measurement accuracy: +/- 1UV index,
- Working current: 0.06mA (standard) / 0.1mA (max.),
- Response wavelength: 200-370 nm,
- Working temperature: -20ºC - + 85ºC,
- PCB size: 28x12mm.

Sensor Module GUVA-S12SD UV features:
- The module based on the Schottky-type photodiode - applicable to the optical mode
- This is a " true "UV sensor instead of calibrated light sensor
- It has high sensitivity, high stability, good linearity
- Power supply: 2.5V - 5V
- Analog output
- Captured wavelength: 240-370nm
- Ultra low power consumption
- Meteorological applications, skin care, industrial UV level measurement
- PCB dimensions: 11x27mm

This photo-resistance module is very sensitive to ambient light. Activation of the microcontroller or retransmission modules,
The brightness module of the ambient light reach the set threshold, the output is high when the ambient light exceeds the set threshold.
The DO output can be connected directly to a microcontroller to detect the light environment and create a light control switch.
It has a speed range of 0% to 100%. Digital Light Intensity Sensor with Photo Resistance with LM393 Controller features:
- Operating voltage: 3.3 - 5 V
- Input current: 50 mA
- Use a very sensitive photo resistance
- Use a LM393 wide voltage comparator, high quality output signal
- Adjustable potentiometer can regulate the brightness of detected light

Led IR 3mm is a pair of infrared LED's consisting of a photodiode (Emitter) that emits an infrared light when polarised through its working voltage ranges and a phototransistor (Receiver) that allows to capture the infrared light emitted by the photodiode.