XL6009 DC-DC Step-Up Booster Controller LM2577 - The XL6009 module has a superior performance than the LM2577 module - The regulator-booster of High performance Characteristic: - Based on the XL6009E1 regulator - Input voltage: 3V-32V, - Output voltage: 5-35V (adjustable), - Output current: 2A maximum 3A (heat sink is required) - Conversion efficiency: up to 94% - Rectifier: not synchronous rectification - Short circuit protection: current limitation, since recovery - Operating temperature: industrial grade (-40 ° C - 85 ° C) - Load regulation: ± 0.5% - Voltage regulation: ± 0.5% - Size: 50 x 22 x 15 mm Code A0005 Available Price €2.45
Hall Effect Sensor Module KY-003 with SH3144E TO-92 This module adapted for the arduino is a unipolar Ic Hall effect magnetic sensor. The Hall effect is when a current passes through a bar of semiconductor (or conductive) material, and if an induction magnetic field B is applied perpendicular to the direction of current flow, a voltage, called Hall voltage, proportional to the magnetic field, and the current appears on the faces sides of the bar. This tension is proportional to the displacement speed of the charge carriers, which is considerably higher in semiconductor materials than in metal conductors. Hall Effect Sensor Module KY-003 with SH3144E TO-92 features: - 3-pin connector: 1- GND 2- VCC 3- Voltage is recovered depending on the magnetic effect - Supply voltage: 5VDC - Output current: 40mA Code M0131 Available Price €1.69
Buzzer PCB Active 5V Black This module is an active buzzer for Arduino and emits different sounds at various frequencies. It does not accept oscillation source, it only receives square waves for drive sound. Buzzer PCB Active 5V Black features: - Operating voltage: 3.3-5.5 VDC - Current consumption: Code M0162 Available Regular price €1.35 -€0.15 Price €1.20
UNO Board CH340 clone - It has an Atmega328P chip running at 16Mhz with factory-loaded bootloader- The Uno R3 module has all the Arduino Uno R3 connectors and is compatible with all Arduino shields Characteristic: - ATmega328P 16MHz chip with external quartz crystal- Microprocessor: ATMega328P- Operating voltage: 5V- Input voltage (recommended): 7-12V- Input voltage (limits): 6-20V- Clock speed: 16 MHz- Digital I / O pins: 14 (6 with PWM)- Analog input pins: 6- DC current for Pin I / O: 20 mA- Flash32 KB of which 0.5 KB are used by the bootloader - AtMega328P- SRAM 2 KB - AtMega328P- EEPROM 1 KB - AtMega328P- Communication: USB female Type B Code B0011 Available Price €7.95
Tower Pro Micro Servo 9g SG90 360 degree Tower Pro Micro Servo 9g SG90 360 degree features: - Operating voltage: 3.0-7.2V- Speed (4.8V without load): 0.12sec / 60 degrees- Strength: 1.2kg / 42.3oz (4.8V); 1.6 kg / 56.4oz (6.0V)- Working temperature: -30 to +60 degrees C- Cable length: approx. 23cm- Includes photo accessories and screws- Dimensions: 22x11.5x27mm Code R0075 Available Price €2.95
Relay Module DC 12V 10A 1 Channel Low/High Trigger Relay Module DC 12V 10A 1 Channel Low/High Trigger features:- Channel: 1 (protected with Optocoupler)- Supply voltage: 12V- Output Current: 10A- Relay activation current: 15mA ~ 20mA- Insulation: Yes- Trigger signal type jumper (low / high)- LED indicator- Dimensions: 30x 54mm- Has a jumper that allows to choose type of trigger signal (low / high) Code RL003 Available Price €2.29
5x Strip Simple Row Male 40 Pins Header Various Colors 5x Strip Simple Row Male 40 Pins Header Various Colors features: - Type: Male- Insertion position: Vertical- Separation between pins: 2.54mm- Quantity: 5 strips of 40 pins Male each Code K0051 Available Price €1.29
1 Channel Relay Module DC 5V 10A Low/High Trigger for Arduino 1 Channel Relay Module DC 5V 10A Low/High Trigger for Arduino features:- Channel: 1 (protected with Optocoupler)- Supply voltage: 5V- Output Current: 10A- Relay activation current: 15mA ~ 20mA- Insulation: Yes- Trigger signal type jumper (low / high)- LED indicator- Dimensions: 30x 54mm- Has a jumper that allows to choose type of trigger signal (low / high)- This module can be controlled directly by the microcontroller (Arduino, 8051, AVR, PIC, DSP, ARM, ARM, MSP430, TTL) Code RL001 Available Price €2.39
DS18B20 Waterproof Digital Temperature Sensor Probe 3m Encapsulated with water resistant stainless steel with sensor dimensions 6 * 50mm, cable length 300 cm. DS18B20 Waterproof Digital Temperature Sensor Probe 3m features:- Based on the DS18B20 chip- Supply voltage: 3 ~ 5.5V- Consumption <5mA- Measuring Range: -55 ° C to 125 ° C- Accuracy: +/- 0,5ºC- Outputs: - GND black - Vcc red - Yellow digital output- Inocidable steel- Cable length: 3m Code S0008 Available Price €4.85
Thermistor NTC 10.0K 5% MF52A epoxy resin coating resistor NTC thermistor - with a negative temperature coefficient, i.e. an increase in temperature causes a decrease in resistance. Thermistor NTC 10.0K 5% MF52A epoxy resin coating resistor features:Size: 3mmRated resistance: R25 = 10.0kB value 25/85 = 3950°KRated power: ‰¤ 50mWTolerance:± 5%Operating temperature: from -40°C to +125°C Tinned steel wire 25mm Code D0090 Available Price €0.49
Thermistor NTC 1.0K 5% MF52A epoxy resin coating resistor NTC thermistor - with a negative temperature coefficient, i.e. an increase in temperature causes a decrease in resistance. Thermistor NTC 1.0K 5% MF52A epoxy resin coating resistor features:Size: 3mmRated resistance: R25 = 1.0kB value 25/85 = 3950°KRated power: ‰¤ 50mWTolerance:± 5%Operating temperature: from -40°C to +125°C Tinned steel wire 25mm Code D0088 Available Price €0.49
Gravity: I2C BME280 Environmental Sensor The BME280 is an environmental sensor (SEN0236) integrating a temperature sensor, a humidity sensor and a barometer. Powered from 3.3 V to 5 V with I2C and SPI interface. Measuring range: temperature: -40 °C to 85 °C, humidity: 0 %RH to 100 %RH, pressure: 300 hPa to 1100 hPa. Code DF017 Available Price €19.95
DS18B20 Digital Temperature Sensor Probe 5m Encapsulated with water resistant stainless steel with sensor dimensions 5,5 * 50mm, cable length 5m. DS18B20 Digital Temperature Sensor Probe 5m features:- Based on the DS18B20 chip- Supply voltage: 3 ~ 5.5V- Consumption <5mA- Measuring Range: -55 °C to 125 °C- Accuracy: +/- 0,5ºC- Outputs: - GND black - Vcc red - Yellow digital output- Inocidable steel- Cable length: 5m Code S0134 Available Price €7.95
All-in-one air quality sensor ZPHS01B: CO2, PM2.5, CH2O, O3... ZPHS01B is an all-in-one air quality module, which integrates laser dust sensor, infrared CO2 sensor, electrochemical formaldehyde, ozone and carbon monoxide sensors, VOC sensor, NO2 sensor, temperature and humidity sensor. Code S0151 Available Regular price €145.90 -€6.00 Price €139.90
Thermistor NTC 5.0K 5% MF52A epoxy resin coating resistor NTC thermistor - with a negative temperature coefficient, i.e. an increase in temperature causes a decrease in resistance. Thermistor NTC 5.0K 5% MF52A epoxy resin coating resistor features:Size: 3mmRated resistance: R25 = 5.0kB value 25/85 = 3950°KRated power: ‰¤ 50mWTolerance:± 5%Operating temperature: from -40°C to +125°C Tinned steel wire 25mm Code D0089 Available Price €0.49
Solar Power Manager 5V The solar power management module with the CN3065 chip is ideal for IoT (Internet of Things) projects with renewable energy. Compared to the previous version of the module, improvements have been made to the energy management of the connected battery. Code DF025 Last items in stock Regular price €17.50 -€4.00 Price €13.50
DS18B20 Probe 2m Submersible Temperature Sensor Encapsulated with water resistant stainless steel with sensor dimensions 5.5*50mm, cable length 200 cm. DS18B20 Probe 2m Submersible Temperature Sensor features:- Based on the DS18B20 chip- Supply voltage: 3 ~ 5.5V- Consumption <5mA- Measuring Range: -55 °C to 125 °C- Accuracy: +/- 0,5ºC- Outputs: - GND black - Vcc red - Yellow digital output- Inocidable steel- Cable length: 2m Code S0015 Available Price €3.79
Digital Thermometer with External Temperature Probe - Immerse the probe in the fish tank to measure the water temperature Digital Thermometer with External Temperature Probe features: - Cable length: 1m- LCD screen- Temperature range: -50 C ~ + 70C- Powered by 2 batteries x LR44 / AG13 button (included)- Cable length: approx.100cm- External Dimensions: 48 x 28.5 x 15.2 mm- Dimension LCD screen: 35 x 16 mm- Color: Black- Used to measure the temperature in: the rooms, the aquarium, terrarium in the heating system, in the car, fridge, freezer Code S0039 Available Price €2.79
DS18B20 Waterproof Digital Temperature Sensor Probe 3m Encapsulated with water resistant stainless steel with sensor dimensions 6 * 50mm, cable length 300 cm. DS18B20 Waterproof Digital Temperature Sensor Probe 3m features:- Based on the DS18B20 chip- Supply voltage: 3 ~ 5.5V- Consumption <5mA- Measuring Range: -55 ° C to 125 ° C- Accuracy: +/- 0,5ºC- Outputs: - GND black - Vcc red - Yellow digital output- Inocidable steel- Cable length: 3m Code S0008 Available Price €4.85
Thermistor NTC 10.0K 5% MF52A epoxy resin coating resistor NTC thermistor - with a negative temperature coefficient, i.e. an increase in temperature causes a decrease in resistance. Thermistor NTC 10.0K 5% MF52A epoxy resin coating resistor features:Size: 3mmRated resistance: R25 = 10.0kB value 25/85 = 3950°KRated power: ‰¤ 50mWTolerance:± 5%Operating temperature: from -40°C to +125°C Tinned steel wire 25mm Code D0090 Available Price €0.49
Thermistor NTC 1.0K 5% MF52A epoxy resin coating resistor NTC thermistor - with a negative temperature coefficient, i.e. an increase in temperature causes a decrease in resistance. Thermistor NTC 1.0K 5% MF52A epoxy resin coating resistor features:Size: 3mmRated resistance: R25 = 1.0kB value 25/85 = 3950°KRated power: ‰¤ 50mWTolerance:± 5%Operating temperature: from -40°C to +125°C Tinned steel wire 25mm Code D0088 Available Price €0.49
Gravity: I2C BME280 Environmental Sensor The BME280 is an environmental sensor (SEN0236) integrating a temperature sensor, a humidity sensor and a barometer. Powered from 3.3 V to 5 V with I2C and SPI interface. Measuring range: temperature: -40 °C to 85 °C, humidity: 0 %RH to 100 %RH, pressure: 300 hPa to 1100 hPa. Code DF017 Available Price €19.95
DS18B20 Digital Temperature Sensor Probe 5m Encapsulated with water resistant stainless steel with sensor dimensions 5,5 * 50mm, cable length 5m. DS18B20 Digital Temperature Sensor Probe 5m features:- Based on the DS18B20 chip- Supply voltage: 3 ~ 5.5V- Consumption <5mA- Measuring Range: -55 °C to 125 °C- Accuracy: +/- 0,5ºC- Outputs: - GND black - Vcc red - Yellow digital output- Inocidable steel- Cable length: 5m Code S0134 Available Price €7.95
All-in-one air quality sensor ZPHS01B: CO2, PM2.5, CH2O, O3... ZPHS01B is an all-in-one air quality module, which integrates laser dust sensor, infrared CO2 sensor, electrochemical formaldehyde, ozone and carbon monoxide sensors, VOC sensor, NO2 sensor, temperature and humidity sensor. Code S0151 Available Regular price €145.90 -€6.00 Price €139.90
Thermistor NTC 5.0K 5% MF52A epoxy resin coating resistor NTC thermistor - with a negative temperature coefficient, i.e. an increase in temperature causes a decrease in resistance. Thermistor NTC 5.0K 5% MF52A epoxy resin coating resistor features:Size: 3mmRated resistance: R25 = 5.0kB value 25/85 = 3950°KRated power: ‰¤ 50mWTolerance:± 5%Operating temperature: from -40°C to +125°C Tinned steel wire 25mm Code D0089 Available Price €0.49
Solar Power Manager 5V The solar power management module with the CN3065 chip is ideal for IoT (Internet of Things) projects with renewable energy. Compared to the previous version of the module, improvements have been made to the energy management of the connected battery. Code DF025 Last items in stock Regular price €17.50 -€4.00 Price €13.50
DS18B20 Probe 2m Submersible Temperature Sensor Encapsulated with water resistant stainless steel with sensor dimensions 5.5*50mm, cable length 200 cm. DS18B20 Probe 2m Submersible Temperature Sensor features:- Based on the DS18B20 chip- Supply voltage: 3 ~ 5.5V- Consumption <5mA- Measuring Range: -55 °C to 125 °C- Accuracy: +/- 0,5ºC- Outputs: - GND black - Vcc red - Yellow digital output- Inocidable steel- Cable length: 2m Code S0015 Available Price €3.79
Digital Thermometer with External Temperature Probe - Immerse the probe in the fish tank to measure the water temperature Digital Thermometer with External Temperature Probe features: - Cable length: 1m- LCD screen- Temperature range: -50 C ~ + 70C- Powered by 2 batteries x LR44 / AG13 button (included)- Cable length: approx.100cm- External Dimensions: 48 x 28.5 x 15.2 mm- Dimension LCD screen: 35 x 16 mm- Color: Black- Used to measure the temperature in: the rooms, the aquarium, terrarium in the heating system, in the car, fridge, freezer Code S0039 Available Price €2.79