Sensor Module FZ0888 IR Infrared Speed Meter Sensor Module FZ0888 IR Infrared Speed Meter features: - The FZ0888 encoder module is a device that can help you in the creation of your robotics and automation project, Whether you want to know the speed of a motor or its exact position - The module has a digital output (DO) which can be connected to your preferred microcontroller. The operating mode: - When the sensor is blocked, the DO output is high - The AO signal is not enabled in this module - Power supply: 3.3-5V - Power consumption current 20 mA max - PCB dimensions: 32 x 14 mm Code S0038 Available Price €1.89
Sensor TCRT5000 Infrared IR Tracker Line Obstacle Phototransistor Sensor TCRT5000 Infrared IR Tracker Line Obstacle Phototransistor features: - Operating range: 0.2mm to 15mm - Receiver: Phototransistor - Emitter: Infrared Led - Wavelength: 950 nm Code S0026 Available Price €0.50
Nano plate V3.0 CH340 + Arduino compatible pins It has an ATMega328P chip running at 16Mhz with a factory loaded bootloader Characteristic: - Microcontroller: ATmega328 - Operating Voltage (logic level): 5V - Input Voltage (recommended): 7-12V - Digital I / O Pins: 14 (6 PWM outputs) - Analog Inputs: 8 (A0-A7) - DC Current per Pin I / O 40 mA - Flash Memory: 32 KB (2 KB used by the bootloader) - SRAM: 2 KB - EEPROM: 1 KB - Clock Frequency: 16 MHz - USB Communication - CH340 - Dimensions: 18 mm x 44 mm Code B0026 Available Price €9.99
Module TCRT5000 Infrared Sensor IR Tracker Line Obstacle The optical module sensor (reflective) with comparator LM393, which detects obstacles with high precision. The ideal obstacle detection detector for the installation of smart robots. TCRT5000 - reflective optical sensor that has a compact construction where the light emitter and receiver are placed in the same direction to detect the presence of a object using infrared reflection on the object. The working wavelength is 950nm. The transmitter is infrared LED and the phototransistor receiver. By using LM393 comparator the module has a binary output (D0) that is at level 1 (object is detected). The sensor allows the detection of an object at a distance of up to 12 mm. Code S0025 Available Price €1.85
DS18B20 Submersible Probe Sensor Temperature Encapsulated with water resistant stainless steel with sensor dimensions 5,5 * 50mm, cable length 100 cm.DS18B20 Submersible Probe Sensor Temperature features:- Based on the DS18B20 chip- Supply voltage: 3 ~ 5.5V- Consumption <5mA- Measuring Range: -55 °C to 125 °C- Accuracy: +/- 0,5ºC- Outputs: - GND black - Red Vcc - Yellow digital output- Inocidable steel- Cable length: 1m Code S0019 Available Price €2.39
Sensor Module Moisture Earth Water Soil The module has two outputs: analog A0 and digital D0 Digital output D0 - signal 0 appears or 1 depending on the threshold setting The threshold is set with the potentiometer The sensor can be used for example: Automatic watering for potted plants With this module you will be able to measure the humidity of the soil, so that you will be able to control the humidity level of the soil of your plants Characteristic: Operation: 3.3V -5V - Sensitivity adjustable by potentiometer - Dual output mode: analog and digital - Red LED - power indicator - Green LED - indicator digital switching output - PCB measurements: 3 x 1.5 cm - Probe measurements: 6 x 3 cm Code S0021 Available Price €1.95
Pro Micro 5V 16Mhz Arduino Compatible Board It has an ATMega32U4 chip running at 16Mhz with a factory-loaded bootloader. It does not include pins so we can solder only the pins we need. Characteristic: - Microcontroller: ATmega32U4 - Operation: 5V - Power (max): 5-12V - Total I / O pins: 20 - PWM pins: 5 - Analog pins: 12 - Maximum current of I / O pins: 40 mA - Maximum current of pin 3.3V: 50 mA - Flash memory: 32 KB (4 KB used by the bootloader) - SRAM: 2.5 KB - EEPROM: 1 KB - Speed: 16 MHz - external interrupt - TWI / I2C, UART, SPI interfaces - Dimensions: 18x33mm - Weight: 30 grams Code B0022 Available Price €9.49
Support for HC-SR04 Ultrasonic Sensor Support for ultrasounds, HC-SR04 distance meter. Ideal to install the sensor on mobile platforms such as robots, vehicles, etc. Support for HC-SR04 Ultrasonic Sensor features: - Material: Acrylic - Color: transparent - Includes screws Code S0005 Available Regular price €1.45 -€0.50 Price €0.95
LEONARDO R3 ATmega32u4 board + Arduino compatible USB cable It has an Atmega32u4 chip running at 16Mhz with a factory-loaded bootloader. The Leonardo module has all the connectors that the Arduino Leonardo R3 and is compatible with all Arduino shields. LEONARDO R3 ATmega32u4 board + Arduino compatible USB cable features: - ATmega32u4 microcontroller, - Operating voltage 5V, - Power (recommended) 7-12V, - Digital pins I / O 20 (of which 7 can be used as PWM outputs), - Analog input pins 12, - DC current through I / O Pin 40 mA, - DC current for pin 3.3V 50 mA, - Flash memory 32 KB (of which 4 KB are used by the bootloader), - SRAM 2.5 KB, - EEPROM 1 KB, - Clock speed 16 MHz, - Interface: UART, USB, SPI, I2C, - USB communication - Atmega32u4, Code B0004 Available Regular price €10.90 -€2.00 Price €8.90
HC-SR04 + Ultrasonic Sensor Support for Arduino compatible sensors It is very easy to make it work with an Arduino, PIC or any other microcontroller.In its output pin we can measure the pulse width PWM depending on the distance of the obstacle.Mounting bracket is ideal for installing the sensor on mobile platforms such as robots, vehicles, etc. HC-SR04 + Ultrasonic Sensor Support Arduino features: - Supply voltage: 5V (4.5V-6V)- Consumption: typical 30 mA, (35 mA max)- Interface: VCC, GND, Signal- Range: 2 cm to 3 meters- Angle 15º- LED measurement indicator in progress- Frequency: 40 kHz for 200 μs- Size: 30 mm x 20 mm Feature of the support: - Material: Acrylic- Transparent color- Includes screws Code S0006 Available Regular price €3.24 -€0.60 Price €2.64
ATmega2560 R3 REV3 16U2 Mega2560 module with USB cable It has an Atmega2560 chip running at 16Mhz with a factory loaded bootloader with 54 digital input / output pins (from which 14 can be used as PWM outputs) and 16 analog inputs, 4 UART (hardware serial ports). The board includes a USB connector, an ICSP port, a reset button and some status LEDs. Atmega16U2 programmed as a USB-to-serial converter. Simply connect it to a computer with a USB cable or power with a power adapter and DC connector. Code B0003 Available Price €24.90
Light Sensor Module BH1750 FVI Arduino and Raspberry compatible Descripción: Light sensor module to measure light intensity and obtain digital data from it.Ideal for projects with ARDUINO.You can use it with PIC, AVR, STM32.BH1750FVI (Rohm) is used to adjust backlighting of LCD screens and keyboards by manufacturers of mobile phones, digital cameras, navigation and portable gaming devices. Light Sensor Module BH1750 FVI Arduino Raspberry features: - Chip BH1750FVI- Supply voltage 3V-5V- Integrated 16bit AD converter- Detection range: 0-65535 lx (with an accuracy of 1 lux)- Interface: II2C- Low dependence on the light source (eg incandescent lamp, fluorescent lamp, halogen lamp, white LED, sunlight)- Dimensions 18.4 x 14 mm Code M0019 Available Price €2.99
Photoresistor GL5516 LDR 10x Photoresistor 5mm GL5516 LDR 5-10k for Arduino.Photoresistor is a resistor whose resistance decreases when increasing the intensity of the light that falls on it. 10x Photoresistor GL5516 LDR features: - Model: GL5516- Spectral peak: 540nm- Maximum DC voltage: 150V- Maximum power: 90mW.- Resistance with light (10lux): 5-10KΩ- Resistance with darkness (0lux): 0.5MΩ- Response time: 20ms- Operating temperature: -30ºC - 70ºC Code S0012 Available Price €0.15
10x Photoresistor GL5539 LDR 50k - 100k Photoresistance is a resistor whose resistance decreases as the intensity of the light that falls on it increases. 10x Photoresistor GL5539 LDR 50k - 100k features:- Model: GL5539- Spectral peak: 540nm- Maximum DC voltage: 150V- Maximum power: 100mW- Resistance with light (10lux): 50-100KΩ- Resistance with darkness (0lux): 5MΩ- Response time: 20ms- Operating temperature: -30ºC - 70ºC Code S0013 Available Price €0.15
Barometric Pressure, Temperature and Altitude Sensor BMP180 Barometric Pressure, Temperature and Altitude Sensor BMP180 features: - Module based on the atmospheric pressure sensor BMP180- Supply voltage: 1.8 - 3.6 V- Energy consumption: 0.5uA- I2C interface- Measuring range: 300 - 1100hPa- Dimensions: 10 x 13 mm- Includes soldering pins Code M0024 Available Regular price €3.89 -€0.59 Price €3.30
GP2Y0A21YK0F Strong Infrared IR Distance Meter Characteristic: - Supply voltage: 4.5V- 5.5V - Consumption: 30 mA typical - Analog output - Range: 10cm to 80cm - Dimensions: 29x12mm - Cable length: 20cm GP2Y0A21YK0F Sharp Analog IR distance sensor 10CM-80CM Arduino Code S0024 Available Price €9.95
Arduino compatible UNO R3 board - It has an Atmega328P chip running at 16Mhz with a factory loaded bootloader - The Uno R3 module has all the connectors than the Arduino Uno R3 and is compatible with all Arduino shields Arduino compatible UNO R3 board features: - Includes USB Cable - ATmega328P 16MHz chip with external quartz crystal - Microprocessor: ATmega328 - Operating voltage: 5V - Input voltage (recommended): 7-12V - Input voltage (limits): 6-20V - Clock speed: 16 MHz - Digital I / O Pins: 14 - Analog input pins: 6 - DC current per I / O Pin: 40 mA - DC Current per Pin 3.3V: 50 mA - Flash32 KB of which 0.5 KB are used by the bootloader - Atmega328 - SRAM 2 KB - Atmega328 Code B0009 Available Price €9.95
Mega2560 R3 DIY PCB Arduino Mega2560 dimensional motherboard to build a Mega by yourself Code B0014 Available Price €1.79
Current Sensor ACS712 AC/DC 20A Hall Current Ammeter Sensor used to measure the current in the circuit to which it is connected. It is based on the ACS712 chip, capable of measuring intensity in both DC and AC. Current Sensor ACS712 AC/DC 20A Hall Current Ammeter features: - Output: Analog - Power: 5V - Accuracy: 1.5% - Measuring capacity: +/- 20A - Dimensions: 31 x 13 mm Code M0105 Available Price €2.99
E18-D80NK Infrared Obstacle Avoidance Sensor Module 3-80cm Smart Car Ideal for projects with ARDUINO, Smart CarDetects transparent and translucent obstaclesE18-D80NK Infrared Obstacle Avoidance Sensor Module 3-80cm Smart Car features:- Current consumption: up to 100 mA- Supply voltage 5V- Current consumption <25mA- Response time of 2 ms- Measured distance: 3-80cm 15st angle- Screw to adjust the sensitivity, the back- Output status led indicator- Operating temperature: -25°C - + 55°C- Material: high-strength plastic- Type of output: normally open, NPN- Dimensions: 18 mm in diameter, Length 45 mm- Cable length 55cm- Departures: - Brown: + - Blue: - - Black: OUT Code S0004 Available Price €6.95
2x CNY70 Reflective Optical Sensor with Transistor Output 2x CNY70 Reflective Optical Sensor with Transistor Output features: - Reflective optical sensor with transistor output- Reflective optical coupler used to distinguish edge or line detection- Dimensions of the housing are 7 x 7 x 6 mm- Supply voltage: 5V- Maximum diode current: 50 mA- Maximum collector-emitter voltage: 32V- Maximum collector current of 50 mA- Quantity: 2 units Code S0121 Available Price €0.74
Arduino compatible Nano V3.0 CH340 board Version compatible with Arduino Nano V3.0 It has an ATMega328P chip running at 16Mhz with bootloader loaded factory. Characteristic: - Microcontroller: ATmega328 - Operating Voltage (logic level): 5V - Input Voltage (recommended): 7-12V - Digital I / O Pins: 14 (6 PWM outputs) - Analog Inputs: 8 (A0-A7) - DC Current per I / O pin 40 mA - Flash memory: 32 KB (2 KB used by the bootloader) - SRAM: 2 KB - EEPROM: 1 KB - Frequency Clock: 16 MHz - USB Communication - CH340 - Dimensions: 18 mm x 44 mm Code B0006 Available Price €5.50
HC-SR04 Ultrasonic Sensor Distance Measuring Module It is very easy to make it work with an Arduino, PIC or any other microcontroller. In its output pin we will be able to measure the PWM pulse width depending on the distance of the obstacle. HC-SR04 Ultrasonic Sensor Distance Measuring Module features: - Supply voltage: 5V (4.5V- 6V) - Consumption: 30 mA typical, (35 mA max) - Interface: VCC , GND, Signal - Range: 2 cm to 3 meters - Angle 15º - LED indicator of measurement in progress - Frequency: 40 kHz for 200 µs - Size: 30mm x 20mm - Quantity: 1 unit Useful links for Arduino / Raspberry programming and projects with boards Arduino / Raspberry: Automatic robot operation with obstacle detection /> Code S0007 Available Price €1.79
Pro Mini 8MHZ 3.3V Arduino compatible board Miniaturized compatible version of Arduino Pro Mini. It has an Atmega328P chip running at 8Mhz with a factory loaded bootloader. It does not include pins so - we can solder only the pins that we need. Pro Mini 8MHZ 3.3V Arduino compatible board features: - ATmega328P 8MHz chip with external quartz crystal - Auto-reset - micro switch - Integrated 3.3V regulator - FLASH 32kB memory - SRAM 1kB memory - EEPROM 1Kb memory - Analog input A0-A7 - 8 PWM channels - external interruption - TWI / I2C, UART, SPI interfaces - Power and status LEDs - Dimensions: 18x33mm - Weight: 30 grams An adapter is needed to program it Code B0017 Available Regular price €8.95 -€2.00 Price €6.95
HC-SR501 Motion Detector Module Passive Infrared PIR Sensor Arduino compatible IR motion detector with a detection range of 7 meters and an operating angle of 120º. An electric pyro sensor , which can detect infrared radiation levels - detect a change in the average IR levels of your detection zone. Ideal for projects with ARDUINO, PIC, AVR, STM32. HC-SR501 Motion Detector Module Passive Infrared PIR Sensor features: - Infrared sensor with control circuit - Adjustable sensitivity and time - Operating voltage: 4.5V- 20V - Consumption in Idle state: Code S0003 Available Price €1.79
Vertical Liquid Level Sensor Switch Level sensor for liquids with float. The liquid level sensor acts as a switch. The state is changed by means of a magnet located on the float. It can be used to detect liquid levels that are too high or too low. Ideal for all those applications where it is necessary to control the level of non-corrosive liquids such as water tanks, aquariums. Characteristic: - Maximum Load: 50W - Maximum Switching Voltage: 250V - Maximum Switching Current: 0.5A - Maximum charging current: 1A - Operating temperature: -10ºC to + 60ºC - Size: 58mm x 18mm Code S0043 Available Price €2.95
Pro Mini 16MHZ 5V Arduino compatible board - Bootloader Pin Header Compatible 100% ARDUINO - Pro Mini Atmega328P 5v 16Mhz - Miniaturized compatible version of Arduino Pro Mini - It has an Atmega328P chip running at 16Mhz with a factory-loaded bootloader. It does not include pins so we can only solder the pins that we need Characteristic: - ATmega328P 16MHz chip with external quartz crystal - Auto-reset - micro switch - Integrated 5V regulator - FLASH 32kB memory - SRAM 1kB memory - EEPROM 1Kb memory - Analog input A0-A7 - 8 PWM channels - External interruption - TWI / I2C, UART, SPI interfaces - Power and status LEDs - Dimensions: 18x33mm - Weight: 30 grams Useful links for Arduino /> Code B0019 Available Regular price €8.95 -€4.00 Price €4.95
DS18B20 Waterproof Digital Temperature Sensor Probe 3m Encapsulated with water resistant stainless steel with sensor dimensions 6 * 50mm, cable length 300 cm. DS18B20 Waterproof Digital Temperature Sensor Probe 3m features:- Based on the DS18B20 chip- Supply voltage: 3 ~ 5.5V- Consumption <5mA- Measuring Range: -55 ° C to 125 ° C- Accuracy: +/- 0,5ºC- Outputs: - GND black - Vcc red - Yellow digital output- Inocidable steel- Cable length: 3m Code S0008 ✗ Out-of-Stock Price €4.85
Arduino compatible Mega2560 R3 CH340 board Version compatible with Arduino Mega2560 R3 It has an Atmega2560 chip running at 16Mhz with a factory-loaded bootloader With 54 digital input / output pins (of which 14 can be used as PWM outputs), 16 analog inputs, 4 UART (hardware serial ports) The board includes a USB connector, an ICSP port , a reset button and some status LEDs Arduino compatible Mega2560 R3 CH340 board features: - Operating voltage: 5V - Input voltage (recommended): 7-12V - Digital I / O Pins: 54 (14 PWM outputs) - Analog input pins 16 - DC current per I / O Pin 40 mA - DC Current per Pin 3.3V 50 mA - Flash: 256 KB of which 8 KB are used by the bootloader - SRAM: 8 KB - EEPROM: 4 KB - Clock speed 16 MHz Code B0015 Last items in stock Price €25.90
M18 Inductive Proximity Sensor M18 Inductive Proximity Sensor features: - Inductive proximity sensor detection switch LJ18A3-8-Z / BX - NPN DC6-36V - A Often used for 3D printer bed leveling - Cylindrical cable type DC 3 cable type (black, brown, blue) - Inductive sensor type - NPN NO (Normal Open ) - Detecting distance 8mm - DC supply voltage 6-36V - Current output 300mA - Response frequency 0.5KHz - Detects iron / aluminum - Operating temperature -25 ° C to + 70 ° C (Non-freezing condition) - Head diameter 18 mm - Size 6.9 x 2cm - Cable length 90cm Code S0042 Available Price €3.49
MQ-3 Alcohol Sensor Module Ethanol Breathalyzer Ethanol alcohol sensor module.MQ gas sensor uses a small indoor heater with an electrochemical sensor.When the alcohol molecules in the air comply with the electrode the ethanol "changes" into acetic acid and then more current is produced.MQ-3 Alcohol Sensor Module Ethanol Breathalyzer features:- Main chip: alcohol sensor MQ-3 and comparator LM393- Working voltage: 5V- Current: 150mA- Digital output: TTL 0/1- Analog output: analog voltage sensing value- Detection concentration:- 0.05mg/L - 10mg/L- Quick response features:- Adjustable sensitivity with the potentiometer- Size: 32mm x 20mmx 18mm Code S0009 Available Price €2.95
Plate STM32F103C8T6 The STM32F103C8T6 has characteristics that surpass the traditional Arduinos type Atmel We go from a speed of execution 16 MHz to 72 MHz and 8-bit to 32-bit. The module is supplied in a soldered version. Code B0010 Last items in stock Price €10.90
DHT22/AM2302 Temperature Humidity Sensor The DHT22 humidity sensor is presented in a plastic body ideal for mounting on a panel or similar. It uses a capacitive sensor that returns a digital signal with the measurement. This sensor, unlike DHT11, is capable of measuring negative temperature values and measures tenths of a degree. DHT22/AM2302 Temperature Humidity Sensor features: - Voltage Operating: 3 to 5.5 VDC - Humidity measurement range: 0-100% ± 2% accuracy - Temperature measurement range: -40ºC to 80ºC ± 0.5º accuracy - Maximum sampling rate: 2 seconds Code S0018 Available Price €3.95
DS18B20 Temperature Sensor 0.5ºC TO-92 Also available with waterproof casing and 100cm cable and 200cm. DS18B20 Temperature Sensor TO-92 0.5ºC Precision 5V Integrated features:- Device function: Temperature sensor- Type of output: Digital- Supply voltage: 3V to 5.5V- Accuracy: ± 0.5ºC- Temperature threshold: Programmable- Operating temperature: -55ºC to + 125ºC- Encapsulated: TO-92- Supply current: 1.5mA Code S0014 Available Price €1.95
Plate UNO CH340 + Arduino compatible switches It has an Atmega328P chip running at 16Mhz with a factory loaded bootloader. The Uno R3 module has all connectors than the Arduino Uno R3 and is compatible with all Arduino shields. Plate UNO R3 CH340 + Arduino compatible switches features: - ATmega328P chip at 16MHz with crystal external quartz - ATmega328P microprocessor with socket - Operating voltage: 5V - Input voltage (recommended): 7-12V - Input voltage (limits): 6- 20V - Clock speed: 16 MHz - Digital I / O Pins: 14 - Analog input pins: 6 - DC current per I / O Pin: 40 mA - DC Current per Pin 3.3V: 50 mA - Flash32 KB of which 0.5 KB are used by the bootloader -Atmega328 - SRAM 2 KB - Atmega328 Code B0023 ✗ Out-of-Stock Price €10.99
Precision Temperature Sensor TO-92 LM335 LM335Z-ST Precision Temperature Sensor TO-92 LM335 LM335Z-ST features:- Power supply from 5 to 30 Vdc- Connection through analog input- Temperature range from -40ºC to 100ºC- Linearity +10 mV / ºK- Accuracy of measurement: ± 2 ° C- Manufacturer: Texas Instruments Code S0120 Available Price €3.99
DIY UNO R3 PCB DIY UNO R3 PCB features: - PCB board for Arduino UNO R3 DIY Code B0020 Backorder Price €0.98
UNO Board CH340 clone - It has an Atmega328P chip running at 16Mhz with factory-loaded bootloader- The Uno R3 module has all the Arduino Uno R3 connectors and is compatible with all Arduino shields Characteristic: - ATmega328P 16MHz chip with external quartz crystal- Microprocessor: ATMega328P- Operating voltage: 5V- Input voltage (recommended): 7-12V- Input voltage (limits): 6-20V- Clock speed: 16 MHz- Digital I / O pins: 14 (6 with PWM)- Analog input pins: 6- DC current for Pin I / O: 20 mA- Flash32 KB of which 0.5 KB are used by the bootloader - AtMega328P- SRAM 2 KB - AtMega328P- EEPROM 1 KB - AtMega328P- Communication: USB female Type B Code B0011 Available Price €7.49
DS18B20 Probe 2m Submersible Temperature Sensor Encapsulated with water resistant stainless steel with sensor dimensions 5.5*50mm, cable length 200 cm. DS18B20 Probe 2m Submersible Temperature Sensor features:- Based on the DS18B20 chip- Supply voltage: 3 ~ 5.5V- Consumption <5mA- Measuring Range: -55 °C to 125 °C- Accuracy: +/- 0,5ºC- Outputs: - GND black - Vcc red - Yellow digital output- Inocidable steel- Cable length: 2m Code S0015 Available Price €3.79
Arduino compatible Due R3 SAM3X8E board It has an Atmel SAM3X8E ARM Cortex-M3 chip running at 84Mhz with a factory-loaded bootloader with 54 digital input / output (of which 12 can be used as PWM outputs), 12 analog inputs, 4 UART (hardware serial ports). The board includes a USB connector, a SPI port, a reset button, a button erase and some status LEDs. Atmega16U2 programmed as a USB / Serial converter for power, simply connect it to a computer with a USB cable or power with a power adapter and DC connector. Characteristic: Operating voltage: 3.3V Input voltage (recommended): 7-12V Digital I / O Pins: 54 (12 PWM outputs) Analog input 12 pins 2 x DAC 2 x TWI 4x UART DC current per DIGITAL I / O pin 130 mA Flash: 512 KB Code B0028 Last items in stock Price €44.95
LM35DZ Temperature Sensor TO-92 LM35 Temperature Sensor LM35DZ TO92 features:- The output is linear and each degree Celsius equals 10 mV- Power supply from 4 to 30 Vdc- Connection through analog input- Temperature range from 0ºC to 100ºC- Linearity +10 mV / ºC- Quantity: 1 unit Code S0016 Available Price €2.49
UNO Board CH340 micro USB clone - It has an Atmega328P chip running at 16Mhz with factory-loaded bootloader- The Uno R3 module has all the Arduino Uno R3 connectors and is compatible with all Arduino shields Characteristic: - Includes USB Cable- ATmega328P 16MHz chip with external quartz crystal- Microprocessor: ATMega328P- Operating voltage: 5V- Input voltage (recommended): 7-12V- Input voltage (limits): 6-20V- Clock speed: 16 MHz- Digital I / O pins: 14 (6 with PWM)- Analog input pins: 6- DC current for Pin I / O: 20 mA- Flash32 KB of which 0.5 KB are used by the bootloader - AtMega328P- SRAM 2 KB - AtMega328P- EEPROM 1 KB - AtMega328P- Communication: micro USB female Type B Code B0053 Available Price €9.59
Analogical Acoustic Sensor 4-Pin Microphone Sound Detector Module Sound detection module for Arduino projects, smart cars. Analogical Acoustic Sensor 4-Pin Microphone Sound Detector Module features: - Adjustable High Sensitivity Acoustic Sensor - LM393 comparator chip - Integrated indicator LED - AO analog output, output voltage signal in time real microphone - DO digital output, sensitivity adjustable through potentiometer - Frequency Range between 30 and 15000 Hz - Power 4 ~ 6V - Measurements 36x16x15mm Code S0017 Available Price €1.79
5.8GHz Doppler Radar Motion Sensor 5.8GHz Doppler Radar Motion Sensor features: - Microwave motion detector module - The main applications can be security alarms and sensors, Automatic door systems, ATM machines, car reverse systems, light sensors, can also be used for traffic monitoring and monitoring applications. - High resistance to radio-frequency interference - Frequency: 5.8GHz - Operating Voltage: 3.3V - 20V TTL 3.3V - Standby Current: 3mA - Detection Range: 3-8 meters, 360 degrees - Power of Output: 2mW - Dimensions: 32x23 mm - R6 - time-delay; initial value 2.2k - 1s, without delay resistance 30s, can be adjusted up to 250k - R9 - for sensitivity adjustment Code M0112 ✗ Out-of-Stock Price €4.46
Current Sensor ACS712 AC/DC 30A for Arduino Sensor used to measure the current in the circuit to which it is connected. Characteristic: - Output: Analog - Power: 5V - Accuracy: 1.5% - Measuring capacity: +/- 30A - Dimensions: 31 x 13 mm Code M0028 Available Price €3.39
UNO WIFI Board CH340 compatible Arduino, NodeMCU, WeMos ESP8266 - It has an Atmega328P chip running at 16Mhz with factory-loaded bootloader- The Uno R3 module has all the Arduino Uno R3 connectors and is compatible with all Arduino shields Characteristic: - ATmega328P 16MHz chip with external quartz crystal- Microprocessor: ATMega328P- Operating voltage: 5V- Input voltage (recommended): 7-12V- Input voltage (limits): 6-20V- Clock speed: 16 MHz- Digital I / O pins: 14 (6 with PWM)- Analog input pins: 6- DC current for Pin I / O: 20 mA- Flash32 KB of which 0.5 KB are used by the bootloader - AtMega328P- SRAM 2 KB - AtMega328P- EEPROM 1 KB - AtMega328P- Communication: micro USB female Code B0070 Available Price €11.99
DHT11 Temperature and Humidity Sensor The humidity sensor DHT11 comes in a plastic body ideal for mounting on a panel or similar. It uses a capacitive sensor that returns a digital signal with the measurement. DHT11 Temperature and Humidity Sensor features: - Operating voltage: 3 to 5 VDC- Humidity measurement range: 20-95% ± 5% accuracy- Temperature measurement range: 0ºC to 50ºC ± 2º accuracy- Maximum sampling rate: 2 seconds- Working current 2.5mA- Iterfaz 1-wire- Dimensions: 2.3 x1.2x 0.5cm- Quantity: 1 unit Code S0010 Available Price €2.49
DHT22/AM2302 Temperature Sensor Humidity PCB + Digital Cable for Arduino - The DHT22 humidity sensor is presented in a plastic body ideal for mounting on a panel or similar. It uses a capacitive sensor that returns a digital signal with the measurement - This sensor, unlike DHT11, is capable of measuring negative temperature values and measures tenths of a degree Characteristic: - Operating voltage: 3 to 5.5 VDC - Humidity measurement range: 0-100% ± 2% accuracy - Temperature measurement range: -40ºC to 80ºC ± 0.5º accuracy - Maximum sampling rate: 2 seconds Useful links for Arduino / Raspberry programming and projects with Arduino / Raspberry boards: Write texts on the OLED 0.96 '' screen - Read the measurements of the temperature / humidity sensor DHT22 / AM2302 on a 0.96 '' OLED screen Send /> Code M0099 Available Regular price €6.49 -€2.00 Price €4.49
M12 Inductive Proximity Sensor PNP DC 6-36V LJ12A3-4-Z/BY 3D Printer M12 Inductive Proximity Sensor PNP DC 6-36V LJ12A3-4-Z/BY 3D Printer features: - This sensor can be configured as auto Z axis level - Sensor detection switch inductive proximity LJ12A3-4-Z / BY - PNP DC6-36V - Often used for 3D printer bed leveling - Typical application: printer bed level sensor 3D - Cylindrical cable type DC 3 cable type (black, brown, blue) - Inductive sensor type - PNP NO (Normal Open) - Detecting Distance 4mm - DC supply voltage 6-36V - Current output 300mA - Response frequency 0.5KHz - Detects iron / aluminum - Operating temperature -25 ° C at + 55 ° C (Non-freezing condition) - Head diameter 12 mm - Size 6.2 x 2cm - Cable length 100cm Code S0036 Available Regular price €3.99 -€0.50 Price €3.49
Sensor Module Infrared Obstacle Detector Car Robot Ideal for projects with ARDUINO, Smart Car. Sensor Module Infrared Obstacle Detector Car Robot features: - Power supply: 3.3 - 5V DC - OUT level 0/1 output - Sensitivity adjustment - Power LED - Distance from detection: 2 - 30cm (max60cm) - detection angle: 35º - LED output status indicator - Dimensions: 40x13x8mm Code S0011 Available Price €1.49
MQ-2 Gas and Smoke Module Sensor Detector Methane Propane Butane LPG MQ-2 Gas and Smoke Module Sensor Detector Methane Propane Butane LPG features: - Main chip: MQ-2 flammable gas and smoke sensor and comparator LM393- Working voltage: 5V- Current: 150mA- Digital output: TTL 0/1- Analog output: analog voltage sensing value- Quick response features:- Concentration detection: 200ppm - 5000ppm LPG, propane 300ppm - 5000ppm butane 5000ppm - 20000ppm methane 300ppm - 5000ppm H2 100ppm -2000ppm alcohol- Adjustable sensitivity with the potentiometer- Size: 32mm x 20mmx 18mm Code S0027 Available Price €2.89
MQ-4 Gas Methane Sensor Module for Arduino MQ-4 Gas Methane Sensor Module for Arduino features:- Main chip: MQ-4 methane sensor and comparator LM393- Working voltage: 5V- Current: 150mA- Digital output: TTL 0/1- Analog output: analog voltage sensing value- Quick response features:- Detection concentration:200ppm- 10000ppm CH4, natural gas- Adjustable sensitivity with the potentiometer- Size: 32mm x 20mmx 18mm Code S0028 Available Price €2.95
MG-5 Gas Methane Sensor Module for Arduino MG-5 Gas Methane Sensor Module for Arduino features: - Main chip: MQ-5 natural gas sensor and comparator LM393- Working voltage: 5V- Current: 150mA- Digital output: TTL 0/1- Analog output: analog voltage sensing value- Quick response features:- Detection concentration:- 200ppm - 10000ppm LPG, LNG, natural gas, propane,- Adjustable sensitivity with the potentiometer- Size: 32mm x 20mmx 18mm Code S0029 Available Price €2.53
Kit de Pro Mini Atmega328 5V 16M + Adaptador USB-UART CP2102 para Arduino Set of Pro Mini Atmega328 5V 16M + USB-UART Adapter CP2102 for Arduino Pro mni has an Atmega328P chip running at 16Mhz with a factory-loaded bootloader. It does not include pins so we can solder only the pins we need. Ideal for connecting TTL RS232 devices to your PC through the USB port. Code B0018 Available Price €12.65
MPU-6050 Accelerometer Module + Gyroscope 3 Ideal for projects with ARDUINO.You can use it with PIC, AVR, STM32. MPU-6050 Accelerometer Module + Gyroscope 3 features:- Chip: MPU-6050- Power supply: 3V-5V- Operating current: 5mA- Communication: I2C- 16-bit analog-digital converter on all axes- Gyroscope scales: ± 250, ± 500, ± 1000 and ± 2000 ° / sec (dps) (programmable by the user)- Accelerometer scales: ± 2g, ± 4g, ± 8g and ± 16g (programmable by the user)- Dimensions: 14 x 21 x 1.3mm- Quantity: 1 unit (1 strip of 8 pin + 1 strip of 8 layered pin) Code M0017 Available Price €4.29
Rain Sensor Module Water Droplet Detector The module has two outputs: analog A0 and digital D0. digital output D0 - signal 0 or 1 appears depending on the configuration of threshold. The threshold is fixed with the potentiometer. Characteristic: - Operating voltage: 3.3V -5 V - Sensitivity adjustable by potentiometer - Dual output mode: analog and digital - Red LED - power indicator - Green LED - digital switching output indicator - Measurements PCB: 3 x 1.5 cm - Sensor measurements: 5.4 x 3.9 cm Code S0022 Available Price €1.69
SparkFun Qwiic Adapter This little board is simply a I2C board to Qwiic converter. It pretty much enables any device with I2C connectors to work with Qwiic system. It has two Qwiic ports - both of them served with the same I2C bus. You simply stick the board on your I2C board and get additional two Qwiic ports. It is as easy as it sounds Code SP033 Available Price €1.89
Water Level Sensor Module One Mega Pic Easily convert water level to analog signal The analog output signal can be read directly on the Arduino board Characteristic: - Operating voltage: 3.3V -5 V - Consumption: less than 20 mA - Sensor type: Analog - Operating temperature: 10º C -30º C - Detection area: 40 mm x 16 mm - Dimensions: 60 mm x 20 mm Code S0023 Available Price €1.39
DHT11 Module Temperature and Humidity Sensor The DHT11 humidity sensor is presented in a plastic body ideal for mounting on a panel or similar. It uses a capacitive sensor that returns a digital signal with the measurement. Characteristic: - Operating voltage: 3 to 5 VDC - Humidity measurement range: 20-95% ± 5% accuracy - Temperature measurement range: 0ºC to 50ºC ± 2º accuracy - Maximum sampling rate: 2 seconds - Working current 2.5mA - 1-wire interface - Dimensions: 32 x14 mm - Quantity: 1 unit with 3x female / female cables Code S0001 Available Price €2.99
ST-LINK V2 Mini STM8 STM32 Simulator Programmer ST-LINK V2 Debugger / chip programmer for STM8 and STM32, supports SWIM and JTAG Serial Wire interfaces. Code B0117 Available Price €11.50