Rain Sensor Module Water Droplet Detector The module has two outputs: analog A0 and digital D0. digital output D0 - signal 0 or 1 appears depending on the configuration of threshold. The threshold is fixed with the potentiometer. Characteristic: - Operating voltage: 3.3V -5 V - Sensitivity adjustable by potentiometer - Dual output mode: analog and digital - Red LED - power indicator - Green LED - digital switching output indicator - Measurements PCB: 3 x 1.5 cm - Sensor measurements: 5.4 x 3.9 cm Code S0022 Available Price €1.69
Sensor Cable - Electrode Pads (3 connector) This is your simple three conductor sensor cable with electrode pad wires. These cables measure 24" long and feature a 3.5mm audio jack on one end with snap type receptacles for biomedical sensor pads. Code SP075 Available Price €8.99
SparkFun Qwiic Adapter This little board is simply a I2C board to Qwiic converter. It pretty much enables any device with I2C connectors to work with Qwiic system. It has two Qwiic ports - both of them served with the same I2C bus. You simply stick the board on your I2C board and get additional two Qwiic ports. It is as easy as it sounds Code SP033 Available Price €1.89
XM-15B Bluetooth Serial Port Module Master Slave Arduino compatible HC-05/06 XM-15B Bluetooth Serial Port Module Master Slave Compatible Arduino HC-05/06 features: * Power 3.0V -6V* 3.3V / 5V logic levels* Bluetooth version V2.1 + EDR* Frequency: 2.4GHz ISM band* Reach approx. 30m* Security: Authentication and encryption* Supports AT commands for configuration through a serial port* Working temperature: -20 ºC to +75 ºC* Working current - 50 mA* PCB dimension: 35 x 19m -Using the conventional Bluetooth CSR chip, the protocol standard Bluetooth V2.1 + EDR, passes the Bluetooth BQB certification-Fast start, only 0.3 seconds to complete the initialization of the complete module (including the Bluetooth protocol stack)- Built-in hardware protector, never hangs Code W0022 Available Price €7.49
Water Level Sensor Module One Mega Pic Easily convert water level to analog signal The analog output signal can be read directly on the Arduino board Characteristic: - Operating voltage: 3.3V -5 V - Consumption: less than 20 mA - Sensor type: Analog - Operating temperature: 10º C -30º C - Detection area: 40 mm x 16 mm - Dimensions: 60 mm x 20 mm Code S0023 Available Price €1.39
DHT11 Module Temperature and Humidity Sensor The DHT11 humidity sensor is presented in a plastic body ideal for mounting on a panel or similar. It uses a capacitive sensor that returns a digital signal with the measurement. Characteristic: - Operating voltage: 3 to 5 VDC - Humidity measurement range: 20-95% ± 5% accuracy - Temperature measurement range: 0ºC to 50ºC ± 2º accuracy - Maximum sampling rate: 2 seconds - Working current 2.5mA - 1-wire interface - Dimensions: 32 x14 mm - Quantity: 1 unit with 3x female / female cables Code S0001 Available Price €2.99
MyoWare 2.0 Cable Shield This Cable Shield provides a 3.5mm connector where you can connect a three-electrode sensor cable, allowing you to test and use the MyoWare 2.0 muscle sensor without actually connecting it to your person. Code SP045 Available Price €7.49
ESP8266 WiFi Motor Drive L293D Expansion Shield Board ESP12E NodeMcu Allows control: - Up to 2 bidirectional current motors- Or 1 stepper motor Shield is compatible with NodeMcu ESP8266 CP2102 WIFI Development Board ESP8266 WiFi Motor Drive L293D Expansion Shield Board ESP12E NodeMcu features: - Minimum operating voltage: 4.5 V- Maximum operating voltage: 36 V- Maximum current: ± 1.2 A- Logic voltage: - 2.3V <= HIV <= VIN (high) - 0.3V <= VIL <= 1.5V (low)- Controller L293D- Measures: 58x42 mm ESP12 port control kit: - D1, D3 - motorA- D2, D4 - motorB Code W0015 Available Price €3.49
ST-LINK V2 Mini STM8 STM32 Simulator Programmer ST-LINK V2 Debugger / chip programmer for STM8 and STM32, supports SWIM and JTAG Serial Wire interfaces. Code B0117 Available Price €11.50
HB100 Microwave Doppler Radar Motion Sensor Microwave motion detector module. The main applications may be security alarms and sensors, systems Automatic doors, ATM machines, car reverse systems, light sensors, can also be used for traffic monitoring and control applications. High resistance to radio frequency interference. Characteristic: - Frequency: 10.525GHz - Frequency Accuracy: 3MHz - Minimum Output: 13dBm EIRP - Operating Voltage: 5V ± 0.25V - Operating current (CW): 60mA maximum, 37mA typical - Harmonic emissions: -10dBm - Detection Range: Over 20 meters - Power of Output: 5mW The device is sensitive to electrostatic discharge and can be damaged during welding. The IF output is particularly sensitive. Code M0026 Available Price €5.44
Qwiic cable kit The SparkFun Qwiic Cable Kit includes 10 cables of different lengths and styles that will connect your Qwiic boards to each other, to a development platform or to a breadboard. Each Qwiic cable is colour coded red, black, blue and yellow with 1mm JST termination. Code SP098 Available Price €11.95
Gravity: Huskylens - An easy-to-use AI camera | vision sensor Huskylens is an easy-to-use AI camera and vision sensor. DFrobot Huskylens (SEN0305) is equipped with multiple functions, such as face recognition, object tracking, object recognition, line tracking, colour recognition and label recognition (QR code). Code DF013 Available Price €71.49
MQ-135 Air Quality Sensor High sensitivity to Ammonia (NH3), Nitrogen oxides (NOx), Alcohol, Sulphides, Benzene (C6H6), CO2, smoke and other harmful gases. The MQ-135 sensor is to sensible for other gasses in the air so that is not possible to get good values for CO2 from it. MQ-135 Air Quality Sensor features:- Main chip: MQ-135 natural gas sensor and comparator LM393- Working voltage: 5V- Current: 150mA- Digital output: TTL 0/1- Analog output: analog voltage sensing value- Quick response features:- Detection concentration: 10ppm - 300ppm NH3 10ppm - 1000ppm Benzene 10ppm - 300ppm Alcohol- Adjustable sensitivity with the potentiometer- Size: 32mm x 20mmx 18mm Code S0034 Available Price €2.45
SparkFun DataLogger IoT - 9DoF SparkFun DataLogger IoT - 9DoF is a pre-programmed data logger to automatically log IMU, GPS and various pressure, humidity and distance sensors - all without having to write a single line of code! DataLogger automatically detects, configures and logs Qwiic sensors. It is specifically designed for users who only need to capture a large amount of data in a CSV or JSON file and return it to their larger project. Code SP099 Last items in stock Price €94.90
ESP8266 5V WiFi Relay Module AP Remote Control + STA You can easily control any device over the Internet through your phone, computer, etc. The module can handle 5 users at the same time, it can work in two modes: STA (client) and AP (access point). In AP mode, the module is connected via WIFI directly to your phone or computer (in open field can be up to 300 meters). In STA mode, the relay module is connected to the access point (router) that supplies the network. Wi-Fi in the room where the relays are located. In this case, the range mainly depends on the power of the access point antennas (routers). You should not turn off after the configuration is completed, as some of the parameters of the WIFI module cannot be saved when power is cut off. Code W0067 Available Price €9.49
MQ-9 Carbon Monoxide Sensor Module MQ-9 Carbon Monoxide Sensor Module features:- Main chip: MQ-9 methane sensor and comparator LM393- Working voltage: 5V- Current: 150mA- Digital output: TTL 0/1- Analog output: analog voltage sensing value- Quick response features:- Detection concentration: 20ppm- 2000ppm carbon monoxide 500ppm- 10000ppm methane CH4 500ppm- 10000ppm LPG- Adjustable sensitivity with the potentiometer- Size: 32mm x 20mmx 18mm Code S0033 Available Price €2.89
Gravity: Huskylens PRO - An easy-to-use AI camera | vision sensor Huskylens PRO is an easy-to-use AI camera and vision sensor. DFrobot Huskylens (SEN0336) is equipped with multiple functions, such as face recognition, object tracking, object recognition, line tracking, colour recognition and label recognition (QR code). Code DF020 Last items in stock Price €95.95
Lilypad Battery Support Button Cell 3V CR2032 Lilypad Battery Support Button Cell 3V CR2032 features: - Battery holder for your Lilypad projects - For 20mm diameter battery type CR2032 - ON / OFF control - Connection points: 4 Code M0072 Available Regular price €3.99 -€1.00 Price €2.99
Buzzer 5V Active Buzzer 4 to 7V DC Buzzer alarm to convert electrical to acoustic signals in robotics devices and Arduino projects. Buzzer 5V Active Buzzer 4 to 7V DC features: - Input voltage: 4V to 7V - Diameter: 12mm - Height: 9.5mm - Spacing Pins: 7.6mm - Maximum Current: Code M0007 Available Price €0.45
MQ-8 Hydrogen Gas Sensor Module MQ-8 Hydrogen Gas Sensor Module features:- Main chip: MQ-8 methane sensor and comparator LM393- Working voltage: 5V- Current: 150mA- Digital output: TTL 0/1- Analog output: analog voltage sensing value- Quick response features:- Detection concentration: 100ppm- 10000ppm hydrogen H2- Adjustable sensitivity with the potentiometer- Size: 32mm x 20mmx 18mm Code S0032 Available Price €2.95
MQ-6 Gas Methane Sensor Module for Arduino MQ-6 Gas Methane Sensor Module for Arduino features:- Main chip: MQ-6 methane sensor and comparator LM393- Working voltage: 5V- Current: 150mA- Digital output: TTL 0/1- Analog output: analog voltage sensing value- Quick response features:- Detection concentration:- 200ppm- 10000ppm LPG, LNG- Adjustable sensitivity with the potentiometer- Size: 32mm x 20mmx 18mm Code S0030 Available Price €2.59
10 Button Tactile Keyboard Matrix Module + Joystick - High quality keyboard, with matrix of 10 keys and joystick- Ideal for your arduino projects, but can also be used with other microcontrollers10 Button Tactile Keyboard Matrix Module + Joystick features:- Momentary contact- Number of push buttons: 10- Joystick: - Two axes (X-Y) - Return to the center - Central push button- Interface: 5 bits- Dimensions: 65mm x 30mm Code M0008 Available Price €3.49
Shield for Arduino Mega2560 Prototype PCB shield board with screw terminal block for Arduino. A very convenient solution for first experiments with Arduino Mega board. To assemble your projects in a comfortable and tidy way, access to all Arduino Mega2560 pins, universal board area, 5V and Gnd buses, reset button. Shield is supplied assembled. Code B0151 Available Regular price €11.95 -€1.00 Price €10.95
Sensor Module ML8511 UV Sensor Module ML8511 UV features: - The module converts the photocurrent into voltage to detect UV intensity - The analog voltage is proportional to UV light detecting - The has a power saving mode of up to 0.1uA, suitable for smart portable devices or mobile phones for use - Power supply: 5V - Analog output - Captured wavelength: 280-390nm - Ultra low power consumption - Meteorological applications, skincare, industrial UV level measurement - Dimensions of PCB: 30x22mm Code S0040 ✗ Out-of-Stock Price €5.29
4x4 High Quality Keyboard Matrix Push Buttons 16 Touch Keys High quality keyboard, with 16-key matrix.Ideal for your arduino projects, but can also be used with other microcontrollers. 4x4 High Quality Keyboard Matrix Push Buttons 16 Touch Keys features: - Momentary contact- Number of push buttons: 16- Dimensions: 39mm x 43mm Code M0009 Available Price €1.49
Sensor Module GUVA-S12SD UV Sensor Module GUVA-S12SD UV features: - The module based on the Schottky-type photodiode - applicable to the optical mode - This is a " true "UV sensor instead of calibrated light sensor - It has high sensitivity, high stability, good linearity - Power supply: 2.5V - 5V - Analog output - Captured wavelength: 240-370nm - Ultra low power consumption - Meteorological applications, skin care, industrial UV level measurement - PCB dimensions: 11x27mm Code S0041 Available Price €7.99
W1209 DC 12V Thermostat + Transparent Box Temperature Controller W1209 DC 12V Thermostat + Transparent Box Temperature Controller features: - Model: W1209 - Supply voltage: DC 12V - Temperature control mode: ON / OFF - Temperature range: -50-110 ° C - Resolution: 0.1 ° C range -9.9 ~ 99.9 ° C, above is 1 ° C - Measure accuracy: 0.1 ° C - Refresh rate: 0.5s - Temperature protection 0-110 ° C - Static current: ‰ ¤ 35mA, working current ‰ ¤ 65mA - Output power: 10A relay - Probe sensor: NTC (10K 0.5%) Waterproof Sensor - Environmental requirements: -10 ~ 60 ° c Humidity 20% -85% - Dimensions: 48 x 40mm Code M0106 Available Regular price €6.44 -€0.08 Price €6.35
Capsule Electret Condenser Microphones 9.5mm MIC Capsule Electret Condenser Microphones 9.5 MIC features: - Measures: 9.7 x 6.7mm- Impedance: 1.5kΩ- Working current: 0.5mA- Working voltage: 4.5V (1.5-10V)- Bandwidth: 50 ... 16000Hz- Signal to noise ratio: ‰¥58dB- Sensitivity: -42 ± 3dB- Sensitivity tolerance: ± 3dB- Distance between terminals: 2.54mm Code M0020 Available Price €0.79
Double Joystick Module 2 Axis XY PS2 Ideal for your arduino projects, but can also be used with other microcontrollers. Double Joystick Module 2 Axis XY PS2 features: - Two axes (XY) - Return to the center - Central push button - Connections: + 5Vcc / GND / VRx / VRy / SW - Dimensions: 4 x 2.6 x 3.2cm Code M0010 Available Regular price €2.50 -€0.31 Price €2.19
Sound Detection Sensor Module Sound detection module for Arduino projects, smart cars.Sound Detection Sensor Module features:- Adjustable High Sensitivity Acoustic Sensor- Chip LM393- Red LED indicator integrated- Frequency range between 30 and 15000 Hz- Power 4 ~ 6V- Measures 32x16x10mm Code S0002 Available Price €1.69
Micro SD Card Reader/Recorder The micro SD card reader module is a simple solution for transferring data to and from a standard micro SD card.The pinout is directly compatible with Arduino, but it can also be used with other microcontrollers.Ideal for projects with ARDUINO, PIC, AVR, STM32.Micro SD Card Reader/Recorder features:- Supply voltage: 4.5V- 5.5V- Adjustable 3.3V built-in regulator for SPI pins- Consumption <200mA- Interface: SPI- Dimensions: 24mmx 42mm x 12mmSupports microSD cards (up to 2G) and micro SDHC (up to 32G) Code M0006 Available Price €2.49
Wemos D1 Mini ESP8266 ESP12E CH340 WiFi Wireless Development Mini ESP8266 ESP12E CH340 WiFi Development NodeMcu module based on ESP8266 controller and programming in Lua language NodeMcu it is equipped with 10 GPIO, PWM, I2C, 1-wire and ADC It works as a standard WiFi 802.11 b / g / n 2.4 GHz Wemos D1 Mini ESP8266 ESP12E CH340 WiFi Wireless Development features: - Compatible with Arduino, programming with the Arduino IDE - Power supply voltage: 5V - LOGICAL LEVELS: 3.3V - 11 input / output pins - 1 ADC (input: 0-3.3V) - Supported protocols: 802.11 b / g / n - Network support: 2.4 GHz - Band: 2400 (MHz) - Wi-Fi Direct (P2p), Soft Access Point - Integrated TCP / IP stack - PLL, regulators and power management units Integrated Code W0061 Available Price €3.49
HC-SR505 Mini Module Motion Detector Infrared PIR Sensor Arduino compatible IR motion detector with a detection range of 3 meters. One sensor electric pyro, which can detect infrared radiation levels - detect a change in the average IR levels of your detection zone. Ideal for projects with ARDUINO, PIC, AVR, STM32. Characteristic: - Operating voltage: 4.5V- 20V - Consumption in idle state: Code S0037 Available Price €2.70
NodeMcu V3 Lua ESP8266 ESP12E CH340 WiFi Wireless Module Development Board NodeMcu module based on ESP8266 controller and programming in Lua language. NodeMcu is equipped with 10 GPIO, PWM, I2C, 1-wire and ADC. ESP8266-12E is an improved version of ESP8266-12. It works as a standard WiFi 802.11 b / g / n 2.4 GHz. USB communication - the CH340 chip. Characteristics of ESP 12E: - Supply voltage: 3.3V (LOGICAL LEVELS: 3.3V) - Supported protocols: 802.11 b / g / n - Network support: 2.4 GHz - Band: 2400 (MHz) - Wi-Fi Direct (P2p), Soft Access Point - TCP Stack / Integrated IP - PLLs, Regulators and Integrated Power Management Units - Output Power: 0.15 (W); + 19.5dBm in 802.11b mode Code W0013 Available Price €4.49
Water Flow Sensor 1-30l /Min YF-S201 The meter built on the basis of a water rotor and a Hall effect sensor Please note this is not a Accuracy. Pulse rate varies slightly depending on flow rate, fluid pressure, and sensor orientation. Water Flow Sensor 1-30l /Min YF-S201 features: - Working voltage range: DC 5 ~ 18 V - Allow pressure: water pressure below 1.75Mpa - Accuracy (flow-pulse output): ± 1 ~ 30 l / min - Use temperature: ‰ ¤ 80 ° C - Load capacity: ‰ ¤ 10 mA (5Vdc) - Operating humidity: 35% ~ 90% RH (frost free) - Temperature: -25 ~ + 80 ° C - Outlet diameter: 1/2 " - Red wire: positive supply - Wire Black: negative power supply - Yellow Cable: signal output - Color: black - Size: 6.2x3.6x3.4 cm Code M0109 ✗ Out-of-Stock Price €5.95
TCRT5000 IR Infrared Sensor Module The optical module (reflective) sensor with CMOS Schmitt inverter 74HC14D, which detects obstacles with high precision. The ideal obstacle detection detector for the installation of smart robots. TCRT5000 - reflective optical sensor that has a compact construction where the light emitter and receiver are placed in the same direction to detect the presence of an object using infrared reflection on the object. The working wavelength is 950nm. The transmitter is infrared LED and the phototransistor receiver. The sensor allows the detection of an object at a distance of up to 15 mm. TCRT5000 IR Infrared Sensor Module features: - The module has an output: digital - CMOS Schmitt inverter 74HC14D - Power supply: 5V - Range: 0.2 mm - 15 mm Code S0048 Available Price €1.49
DS3231 Precision RTC Real Time Clock Module AVR ARM DS3231 Precision RTC Real Time Clock Module AVR ARM features: - Can be used in projects of Arduino, Raspberry Pi, PIC, AVR- Function compatible with the DS 3231- Power supply voltage: +2.3 V to +5.5 V- Temperature range: -40 ° C to + 85 ° C- Low energy consumption- Full clock calendar functions that include seconds, minutes, hours, date, month and year and valid until leap year compensation- Two alarm calendar- Interface: I2C Code RA011 Available Price €2.95
Passive Buzzer 5V The piezoelectric buzzer has a simple structure in which a ceramic piezoelectric disk is affixed to a vibrating plate. An alternative voltage applied to this element will cause a contraction or diametrical expansion of the element. This feature is used to fold a vibrating plate, which generates sounds. 2x Passive Buzzer 5V features: - Input voltage: 3V to 12V - Diameter: 12mm - Height: 7.5mm - Pin spacing: 6.5mm - Impedance: 16 Ohm - Working frequency: 2 to 5 KHz - Quantity: 1 unit Code M0011 Available Price €0.39
HX711 Module Weighing Pressure Sensor 24 Bits The module uses a 24-bit high precision A/D conversion chip HX711.The input circuit can be configured to provide a bridge.The electric bridge voltage sensor model (such as pressure, weight) is an ideal sampling module with high precision and low cost. HX711 Module Weighing Pressure Sensor 24 Bits features: - Two selectable differential input channels- Active low noise PGA with selectable gain of 32, 64 and 128- Power supply regulator for load cell and ADC analog power supply- Oscillator on chip that does not require external component with optional external glass- Power-on-reset on the chip- Simple serial control and serial interface: controls driven by pins, programming is not required- Output data rate 10SPS or 80SPS selectable Code M0118 Available Regular price €2.79 -€0.47 Price €2.32
NRF24L01 + Wireless Antenna Transceiver 2.4 GHz 1Km PA LNA - This module includes PA preamplifier and LNA (Low-noise amplifier)- Comes with the SMA antenna for 2.4GHz (2dB)- Outdoor - transmission up to 250kbps and a distance of up to 1 kilometer- Works at 2.4GHz frequencies (free frequency) and is ideal for telemetry projects, robots, peripherals control, video game control applications, remote temperature sensors, pressure, alarms, etc ... NRF24L01 + Wireless Antenna Transceiver 2.4 GHz 1Km PA LNA features: * Based on chip NRF24L01 +* Free band: 2.4GHz ISM* Speed: 250kbps, 1Mbps, 2Mbps* Work current- Reception: 45 mA- Transmission: 115 mA (4.2uA -sleep mode)* Receiving sensitivity:-104dB 250kbps- 95dB 1Mbps- 92dB 2Mbps* SPI interface Code W0063 Available Regular price €6.95 -€1.50 Price €5.45
VGA camera 640x480 OV7670 B 0.3MPx 30fps Cmos Camera module for Arduino, Raspberry Pi 2 and Pi 3, B and B +. VGA camera 640x480 OV7670 B 0.3MPx 30fps Cmos features: > - Input voltage 2.5V-3V - Operating power 60mW / 15fps VGA YUV - Resolution VGA 640x480 pixels (30fps) - Maximum frame rate 30fps VGA - Flicker 50Hz / 60Hz automatic detection - Lens size 1/6 " - Angle of view 25 ° - Sensitivity 1.3V / (lux- seg) - SCCB (Serial Camera Control Bus) interface - Output format · 8 Bits - YUV / YCbCr 4: 2: 2 - RGB 565/555/444 - GRB 4: 2: 2 - RAW RGB data - High sensitivity Light operation - Automatic adjustment - Color level saturation - Edge enhancement - Noise level Code M0103 Available Regular price €5.79 -€1.00 Price €4.79
DS1307 AT24C32 RTC real time module Can be used in projects of Arduino, PIC, AVR, STM32 and other. DS1307 AT24C32 RTC real time module features: - Based on DS1307Z- EEPROM memory 24C32 (4Kx8) available for the user- I2C interface- Hour, minutes, seconds, day, month, date, year- AM / PM time- Compensation of leap years- Quartz 32.768kHz- Dimensions: 28x26x8mm- Includes CR2032 3V battery Code M0101 Available Price €1.79
Rotary Encoder EC11 with Push Button Switch It can be used to control the microprocessor of the Arduino AVR PIC system and others, or as a digital potentiometer rotating the rotary encoder can be counted in positive and negative, depending on the direction of rotation; with the button of the rotary encoder can be reset to its initial state, which starts counting from 0. Code M0012 Available Price €1.39
Wireless Module Arduino compatible HC-05 HC05 Bluetooth The bluetooth HC-05 module is one of the best options for projects where you need wireless communications. The transceiver module (transmission / reception) allows bluetooth wireless connections as master or slave, works transparently as if making a wired RS-232 TTL serial connection. Arduino Wireless Module HC-05 HC05 Bluetooth features: - CSR BC417 Chipset - Power: 3.3. - Bluetooth version V2.0 + EDR - Frequency: 2.4GHz ISM band - Modulation: GFSK - Approximate range: 10m - Security: Authentication and encryption - Speed- & gt; Asynchronous: 2.1Mbps (Max) / 160 kbps; Synchronous: 1Mbps / 1Mbps - Supports AT commands for configuration through a serial port temperature: -20 ºC to +75 ºC Code W0019 ✗ Out-of-Stock Price €8.90
Load Cell Weight Sensor 1kg Load Cell 1 kg Scale Sensor Weight Arduino Load cell to measure weight up to 1kgThe transducer measures the deformation of the metal structure and converts it into a few mV. Load cell Load Cell Weight Sensor 1kg features: - Load range: 1kg- Operating voltage: 3VDC ~ 14 VDC.- Nominal output: 1.0 ± 0.15mV / V- Repeatability: 0.03% FS- Effect of the temperature at the outlet: 0.01% F.S / ° C Code M0124 Available Regular price €2.99 -€0.99 Price €2.00
TM1637 4-Digit Digital Display Module Module for Arduino, Raspberry Pi 2 and Pi 3, B and B +. The display module 4-digit LED with TM1637. The unit can be controlled with just two DIO and CLK control lines. TM1637 4-Digit Digital Display Module features: - 3V-5V supply voltage - Current consumption 250 mA - 7-segment display 4 digits common anode - Digit size: 0.36 inches - Dimensions: 42x24x11mm Code M0104 Available Price €2.15
Load Cell Weight Sensor 2kg Load cell Load Cell Weight Sensor 2kg features: - Load cell to measure weight up to 2kg- The transducer measures the deformation of the metal structure and converts it into a few mV- Load range: 2kg- Operating voltage: 3VDC ~ 14 VDC- Nominal output: 1.0 ± 0.15mV / V- Repeatability: 0.03% FS- Effect of the temperature at the outlet: 0.01% F.S / °C- Effect of temperature on zero: 0.05% F.S / °C- Zero: ± 0.1000 mV / V- Input impedance: 1115 + -10% Ω- Output impedance: 1000 + - 10% Ω- Insulation resistance:> = 1000 MΩ- Safe Overload Rate: 150% FS- Final overload rate: 200% FS- Temperature range: -20 - 60 °C- Material: Aluminum alloy- Degree of protection: IP65 Code M0125 Available Regular price €2.99 -€0.99 Price €2.00
DS1302 Real Time Clock RTC Module AVR ARM PIC Ideal for projects with ARDUINO you can use it with PIC, AVR, STM32.Provides seconds, minutes, time and date, calendar up to the year 2100.DS1302 Real Time Clock RTC Module AVR ARM PIC features:- Chip: DS1302- Power supply: 2V-5V- Operating current: <2mA- Dimensions: 44 x23 x 8mm- Battery not included in this sale- Connect the RTC to your ArduinoVCC -> Arduino + 3.3VGND -> Arduino GndCLK -> (SCLK_PIN)DAT -> (IO_PIN)RST -> (CE_PIN) Code M0014 Available Price €1.96
Load Cell Weight Sensor 5kg Load cell Load Cell Weight Sensor 5kg features: - Load cell to measure weight up to 5kg- The transducer measures the deformation of the metal structure and converts it into a few mV- Load range: 5kg- Operating voltage: 3VDC ~ 14 VDC- Nominal output: 1.0 ± 0.15mV / V- Repeatability: 0.03% FS- Effect of the temperature at the outlet: 0.01% F.S / °C- Effect of temperature on zero: 0.05% F.S / °C- Zero: ± 0.1000 mV / V- Input impedance: 1115 + -10% Ω- Output impedance: 1000 + - 10% Ω- Insulation resistance:> = 1000 MΩ- Safe Overload Rate: 150% FS- Final overload rate: 200% FS- Temperature range: -20 - 60 °C- Material: Aluminum alloy- Degree of protection: IP65 Code M0126 Last items in stock Regular price €2.99 -€0.99 Price €2.00
TPA3116D2 Class D 2X50W Dual Channel Amplifier TPA3116D2 Class D 2X50W Dual Channel Amplifier features: - Chip: TPA3116D2 - Power supply: DC 12 V ~ 24 V - Channel Type: Dual Channel - Output power: 2 x 50 W - Input impedance: 51K x 2 - Output Match: 4 ~ 8 Ohm - Frequency Range: 14 ~ 100 KHz - Short circuit protection: Yes - Overheating protection: Yes - Over voltage protection: Yes - Size (LxWxH): 105 x 65 x 23 mm Code M0034 Available Price €11.50
Load cell 10kg Load cell Load Cell Weight Sensor 10kg features: Load range: 10kg Operating voltage: 3VDC ~ 14 VDC. Rated output: 1.0 ± 0.15mV/V. Repeatability: 0.03% FS Effect of temperature on output: 0.01% F.S / ° C Temperature effect on zero: 0.05% F.S / ° C Code M0127 Available Regular price €3.49 -€1.00 Price €2.49
Load Cell 20kg Load cell Load Cell 20kg features: - Load range: 20kg- Operating voltage: 3VDC ~ 14 VDC- Nominal output: 1.0 ± 0.15mV / V- Repeatability: 0.03% FS- Effect of the temperature at the outlet: 0.01% F.S /°C- Effect of temperature on zero: 0.05% F.S /°C- Zero: ± 0.1000 mV / V- Input impedance: 1115 + -10% Ω- Output impedance: 1000 + - 10% Ω- Insulation resistance:> = 1000 MΩ- Safe Overload Rate: 150% FS- Final overload rate: 200% FS- Temperature range: -20 - 60 °C- Material: Aluminum alloy- Degree of protection: IP65- Cable length: 25 cm- Size: 75 x 12.7 x 12.7 mm- Wiring:* Red: Feeding +* Black: Source -* Green: Sign +* White: Signal - Code M0128 Available Regular price €3.19 -€1.00 Price €2.19
VGA Camera 640x480 FIFO AL422 Buffer OV7670 30fps Camera module for Arduino, Raspberry Pi 2 and Pi 3, B and B +. AL422B Video buffer consists of 3M-bits of DRAM, and it is configured as 393.216 x 8 bit FIFO (First In First Out). The interface is very easy to use because all operations are controlled by the internal DRAM memory controller. VGA Camera 640x480 FIFO AL422 Buffer OV7670 30fps features: - Input voltage: 2.5V-3V - Controller: AL422B FIFO buffer - Operating power: 60mW / 15fps VGA YUV - VGA resolution: 640x480 pixels (30fps), - Maximum frame rate: 30fps VGA - Flicker: 50Hz / 60Hz auto detection - Lens size: 1/6 " - Angle of view: 25 ° - Sensitivity: 1.3V / (lux- sec) - SCCB (Serial Camera Control Bus) interface - Output format: 8 Bits - YUV /> Code M0114 Available Price €14.59
10x Photoresistor GL5528 LDR Photoresistor is a resistor whose resistance decreases with increasing intensity of lightthat affects her 10x Photoresistor GL5528 LDR features: - Model: GL5528- Spectral peak: 540nm- Maximum DC voltage: 150V- Maximum power: 100mW- Resistance with light (10lux): 10-20KΩ- Resistance with darkness (0lux): 1MΩ- Response time: 20ms- Operating temperature: -30ºC - 70ºC- 10k - 20k Arduino PiC 5mm- Quantity: 10 units Code S0050 Available Price €0.15
Transceiver 1km SI4432 433MHz Wireless Transmitter Telemetry Transceiver 1km SI4432 433MHz Wireless Transmitter Telemetry features: - Transceiver based on the SI4432 Silicon Labs chip - Ultrathin ultra small (16.5 × 17 mm) - Good harmonics: easy for FCC / CE certification - Penetration capacity (measured through 8 floors) - Frequency range: 433.92MHz - Sensitivity down to -121 dBm - Maximum output power: 20dBm - Data transfer rate: 0.123-256 kbps - FSK, GFSK and OOK modulation - Power supply: 1.8-3.6 V - Ultra low power shutdown mode - Digital indication of received signal strength (RSSI) - Time to wake up - Bidirectional antenna switch control and automatic adjustment - Configurable packet structure - Preamble detection Code W0075 Available Price €4.99
Reed Switch Module Magnetic Foil Sensor This Reed switch module uses a small device called a reed switch. When the device is exposed to a magnetic field, the two ferrous materials inside the switch come together and the switch closes. When the magnetic field is removed the switch opens. The operating mode: - When exposed to a magnetic field the DO output is high - Power supply: 3.3-5V - Contact type: SPST-NO (normally open) - Use temperature: -20ºC to + 80ºC - Type Output: Digital (1 - 0) - PCB dimensions: 32 x 14 mm Code S0045 Available Price €1.39
1.5km radius SI4432 433MHz RF Telemetry Transceiver based on the SI4432 Silicon Labs chip Industry standard model Capacitive components manufactured by Murata with 10ppm high precision glass Outdoors - a distance of up to 1.5 km 1.5km radius SI4432 433MHz RF Telemetry features:- Supply voltage: 1.8 ~ 3.6VDC (Note: a voltage higher than 3.6 V will cause permanent damage to the module) - Communication level: 0.7VDC ~ 3.6V (VCC refers to the module supply voltage) - Working frequency: 425M ~ 525MHz (via software setting, the module uses 30M glass) - Measured distance: 1500m (clear and open, maximum power, height 1.5m, air speed 1k) - Transmission power: up to 20dBm (about 100mW) - Air rate: 0.123k ~ 256Kbps (software adjustable, low airspeed recommended) Code W0080 ✗ Out-of-Stock Price €4.99
MH-Z19C Infrared Sensor module 5000ppm CO2 monitor HVAC PWM output UART CO2 sensor model MH-Z19C. High precision working voltage 5.0±0.1V DC. The measuring range is between 0 and 5000 ppm. It has a low power consumption. UART and PWM output. Code S0044 Backorder Price €29.49
Ethernet Shield W5100 Web Server Shield Ethernet for Arduino boards and compatible based on the Wiznet W5100 chip. Provides an easy way to connect your module to the local network now internet. Compatible with the official Arduino Ethernet library. With this shield you can build a web server. It can be used as a server or as a client. It has support for a microSD that can be used to store files for distribution on the network. Ethernet Shield W5100 Web Server features: - Controller: Wiznet W5100 - Supports protocols TCP and UDP - Supports up to 4 simultaneous connections - Compatible with all Arduino versions: UNO, mega 1280/2560 - Dimensions: 74 x 54 x 25mm Code W0007 Available Price €21.95
EMG Muscle Signal Sensor Signal Electromyography EMG Muscle Signal Sensor Signal Electromyography features: EMG Muscle signal sensor module kit with 6 disposable electrodes The EMG sensor serves as a bridge to detect small electrical pulses product of muscle activity and transform them into a signal recognizable by Arduino. NOTE: DO NOT USE THIS SENSOR FOR MEDICAL PURPOSES. Code Examples: https: //github.com/AdvancerTechnologies/MuscleSensorV3 Code M0116 Last items in stock Price €36.90