TPA3116D2 Class D 2X50W Dual Channel Amplifier TPA3116D2 Class D 2X50W Dual Channel Amplifier features: - Chip: TPA3116D2 - Power supply: DC 12 V ~ 24 V - Channel Type: Dual Channel - Output power: 2 x 50 W - Input impedance: 51K x 2 - Output Match: 4 ~ 8 Ohm - Frequency Range: 14 ~ 100 KHz - Short circuit protection: Yes - Overheating protection: Yes - Over voltage protection: Yes - Size (LxWxH): 105 x 65 x 23 mm Code M0034 Available Price €11.50
VGA Camera 640x480 FIFO AL422 Buffer OV7670 30fps Camera module for Arduino, Raspberry Pi 2 and Pi 3, B and B +. AL422B Video buffer consists of 3M-bits of DRAM, and it is configured as 393.216 x 8 bit FIFO (First In First Out). The interface is very easy to use because all operations are controlled by the internal DRAM memory controller. VGA Camera 640x480 FIFO AL422 Buffer OV7670 30fps features: - Input voltage: 2.5V-3V - Controller: AL422B FIFO buffer - Operating power: 60mW / 15fps VGA YUV - VGA resolution: 640x480 pixels (30fps), - Maximum frame rate: 30fps VGA - Flicker: 50Hz / 60Hz auto detection - Lens size: 1/6 " - Angle of view: 25 ° - Sensitivity: 1.3V / (lux- sec) - SCCB (Serial Camera Control Bus) interface - Output format: 8 Bits - YUV /> Code M0114 Available Price €14.59
Transceiver 1km SI4432 433MHz Wireless Transmitter Telemetry Transceiver 1km SI4432 433MHz Wireless Transmitter Telemetry features: - Transceiver based on the SI4432 Silicon Labs chip - Ultrathin ultra small (16.5 × 17 mm) - Good harmonics: easy for FCC / CE certification - Penetration capacity (measured through 8 floors) - Frequency range: 433.92MHz - Sensitivity down to -121 dBm - Maximum output power: 20dBm - Data transfer rate: 0.123-256 kbps - FSK, GFSK and OOK modulation - Power supply: 1.8-3.6 V - Ultra low power shutdown mode - Digital indication of received signal strength (RSSI) - Time to wake up - Bidirectional antenna switch control and automatic adjustment - Configurable packet structure - Preamble detection Code W0075 Available Price €4.99
1.5km radius SI4432 433MHz RF Telemetry Transceiver based on the SI4432 Silicon Labs chip Industry standard model Capacitive components manufactured by Murata with 10ppm high precision glass Outdoors - a distance of up to 1.5 km 1.5km radius SI4432 433MHz RF Telemetry features:- Supply voltage: 1.8 ~ 3.6VDC (Note: a voltage higher than 3.6 V will cause permanent damage to the module) - Communication level: 0.7VDC ~ 3.6V (VCC refers to the module supply voltage) - Working frequency: 425M ~ 525MHz (via software setting, the module uses 30M glass) - Measured distance: 1500m (clear and open, maximum power, height 1.5m, air speed 1k) - Transmission power: up to 20dBm (about 100mW) - Air rate: 0.123k ~ 256Kbps (software adjustable, low airspeed recommended) Code W0080 ✗ Out-of-Stock Price €4.99
Ethernet Shield W5100 Web Server Shield Ethernet for Arduino boards and compatible based on the Wiznet W5100 chip. Provides an easy way to connect your module to the local network now internet. Compatible with the official Arduino Ethernet library. With this shield you can build a web server. It can be used as a server or as a client. It has support for a microSD that can be used to store files for distribution on the network. Ethernet Shield W5100 Web Server features: - Controller: Wiznet W5100 - Supports protocols TCP and UDP - Supports up to 4 simultaneous connections - Compatible with all Arduino versions: UNO, mega 1280/2560 - Dimensions: 74 x 54 x 25mm Code W0007 Available Price €21.95
2km radius SI4463 433MHz RF Telemetry Arduino compatible A compact, low-power Bottom Effect System Transceiver. Transceiver based on the SI4463 Silicon Labs chip. Industry standard model. In full power operating conditions, open the communication distance up to 2000 km. Much more than the SI4432. Si4463 is a high performance 433 MHz transceiver. and low current consumption of the EZRadioPRO series, which includes a complete transmitter and receiver. Higher sensitivity -126dBm. The maximum output power of + 20dBm, support (G) FSK, 4 (G) FSK, (G) MSK, OOK and ASK modulation. The data rate in the range of 100bps ~ 1Mbps. Operating voltage of 1.8V ~ 3.6V. FCC approval / IC. 2km radius SI4463 433MHz RF Arduino Telemetry features: - Supply voltage: 1.8 ~ 3.6VDC Code W0077 Available Price €7.24
Mini Submersible Water Pump DC 3V 120L/H Characteristic: - Operating voltage: 3-6V - Max flow: 80-120 l / h - Maximum pumping height: 40-110cm - Continuous working time of 500 hours - Cable length: 20cm - Inside outlet diameter: 5 mm - Outside outlet diameter: 7.5 mm - Dimensions: 45mm x 23mm x 30mm Code M0040 Available Regular price €2.49 -€0.51 Price €1.98
SIM808 GPRS GSM GPS Bluetooth SIM Quadband SIM808 GPRS GSM GPS Bluetooth SIM Quadband features: - SIM card SIM808 GPRS GSM GPS Bluetooth SIM - Supply voltage range: 3.4-4.4V - Four bands GSM 850/900/1800 / 1900MHz - GPRS multi-slot class 12/10 - GPRS mobile station class B - According to GSM phase 2/2 + - Class 4 (2 W at 850/900 MHz) - Class 1 (1W at 1800 / 1900MHz) - Control by AT commands (3GPP TS 27.007.27.005 and enhanced AT Commands from SIM Com) - Operating temperature: -40 to + 85 ° C - PCB dimension: 38x38mm - GPS sensitivity - Tracking: -165dBm Cold start Sensitivity - Cold start: -147dBm - Time to first solution - Cold start: 30 s - Start to warm up: 28s - Already hot: 1s - Accuracy Code W0069 Available Regular price €19.89 -€3.00 Price €16.89
TPA3118 1X60W PBTL Channel Only Amplifier TPA3118 1X60W PBTL Channel Only Amplifier features: - Chip: TPA3118 - Power supply: DC 8V ~ 24V - Channel type: Single channel - Output power: 1 x 60 W. - Matching output: 4 ~ 8 Ohm - Mono PBTL mode - Size (LxWxH): 46 x 35 x 13 mm Code M0036 Available Price €6.46
Shield Li-Po Battery for WeMos D1 Mini ESP826 Shield Li-Po Battery for WeMos D1 Mini ESP826 features: Connect the lithium battery to this shield to supply power for the entire D1 mini system. When the battery is depleted, it is not necessary disconnect the battery, just use the usb port to charge directly. - Charging voltage: max: 10V, recommend: 5V - Charging current: max: 1A - Voltage lithium battery: 3.3-4.2V - Boost power supply: 5V (max: 1 A) - LED color: red for charging, green for fully charged - Ports: * Micro USB - Charging port (normal 5V) * Connect to the lithium battery (normal 3.3-4.2V) * J1 - setting the maximum charging current, 0.5 A or 1A Code W0076 Available Regular price €4.76 -€1.00 Price €3.76
16 Channel Relay Module 12V 10A This module can be controlled directly by the microcontroller (Arduino, 8051, AVR, PIC, DSP, ARM, ARM, MSP430, TTL, PLC output).16 Channel Relay Module 12V 10A AVR features:- Channels: 16 (independent protected with Optocouplers)- Supply voltage: 12V- Output Current: 10A- Relay activation current: 3mA- Insulation: Yes- Low shot: 0-2V- LED indicator: For each channel- Dimensions: 18x 9x 2cm Code RL009 Available Price €15.49
SIM800L GPRS GSM SIM Board Quadband SIM800L GPRS GSM SIM Board Quadband features: Package includes: - SIM800L module, - 2x pin headers, - Spring antenna, - 3G PCB antenna - 15cm cable. - Supported SIM format: Micro SIM. Code W0017 Available Price €6.49
Wireless Module Arduino compatible HC-06 HC06 The Bluetooth HC-06 module is one of the best options for projects where you need wireless communications. Arduino Wireless Module HC-06 HC06 features: - CSR BC417 Chipset - Power: 3.3V - Bluetooth version V2.0 + EDR - Frequency: 2.4GHz band ISM - Modulation: GFSK - Range approx. 10m - Security: Authentication and encryption. - Speed- & gt; Asynchronous: 2.1Mbps (Max) / 160 kbps; Synchronous: 1Mbps / 1Mbps - Supports AT commands for configuration through a serial port - Working temperature: -20 ºC to +75 ºC - Working current - pairing: 80 mA - Transmission: 8mA - Size: 28 x 12mm Code W0018 Available Price €9.50
2 Channel Relay Module 5V 10A for Arduino 2 Channel Relay Module 5V 10A for Arduino features:- 5V relay module with 2 optocoupled channels- This module can be controlled directly by the microcontroller (Arduino, 8051, AVR, PIC, DSP, ARM, ARM, MSP430, TTL)- Channels: 2 (independent protected with Optocouplers)- Supply voltage: 5V- Output Current: 10A- Relay activation current: 15mA ~ 20mA- Insulation: Yes- LED indicator: For each channel- Dimensions: 40x 50mm Code RL006 Available Regular price €1.99 -€0.35 Price €1.64
Micro Usb to DIP Adapter Mini Arduino Module Electronic Converter PCB Micro Usb to DIP Adapter Mini Arduino Module Electronic Converter PCB features: - Compatible with male pin strip (pin spacing 2.54mm) - PCB dimensions: 15mm x 13mm Code M0044 Available Price €0.98
RFID Module with Card and Pendant It is compatible with almost any microcontroller, Arduino, PIC, AVR.It can be used in Access Control projects and Alarm projects. RFID Module with Card and Pendant features: - Supports Quick CRYPTO1 and MIFARE- Operating current: 13-26mA at 3.3V- Standby current: 10-13mA to 3.3V- Sleep-mode current: <80μA- Maximum current: 30mA- Frequency of operation: 13.56Mhz- Reading distance: 0 to 60mm- Communication protocol: SPI- Maximum SPI speed: 10Mbit / s- Maximum data rate: 10Mbit / s- Operating temperature: -20 to 80ºC- Humidity of operation: 5% -95% Code M0015 Available Price €2.79
ENC28J60 Ethernet LAN Network Module for Arduino AVR LPC STM3 The network module communicates with the Arduino type board through the SPI protocol ideal for projects with ARDUINO, PIC, AVR, STM32. ENC28J60 Ethernet LAN Network Module for Arduino AVR LPC STM3 features: - Chip ENC28J60 Microchip- Module: 10Base-T- 3.3V power- SPI interface- 25Mhz speed- LED status LED- Hanrun network transformer- Network Interface board HR911105A- Operating temperature: -40ºC to + 85ºC- Dimensions: 55x 35x 16 mm Code W0002 Available Price €8.99
ESP8266 WIFI Module ESP-01 for Electronic Sensor Robotics WIFI transceiver based on the ESP8266 controller. It has a microcontroller and 2 GPIO pins to be able to operate autonomously without the need for an external microcontroller. Characteristic: - Voltage of power: 3.3V - Supported protocols: 802.11 b / g / n - Network support: 2.4 GHz - Band: 2400 (MHz) - Wi-Fi Direct (P2p), Soft Access Point - Integrated TCP / IP stack - PLL, regulators and integrated power management units - Output power: 0.15 (W); + 19.5dBm in 802.11b mode - Consumption in low power mode: Code W0003 Available Price €1.95
8 Channel 5V 10A Relay Module Arduino compatible 5V Relay Module with 8 opto-coupled channels. This module can be directly controlled by the microcontroller ( Arduino, 8051, AVR, PIC, DSP, ARM, ARM, MSP430, TTL). 8 Channel Arduino 5V 10A Relay Module features: - Channels: 8 (independent protected with Optocouplers) - Supply Voltage: 5V - Output Current: 10A - Relay activation current: 15mA ~ 20mA - Isolation: Yes - LED indicator: For each channel - Dimensions: 54x 135mm Code RL008 Available Price €9.49
Led Matrix 8x8 MAX7219 Soldier Led Matrix 8x8 MAX7219 Soldier features: - MAX7219 controller module with 8x8 led matrix + cables - 8X8 LED matrix controlled by MAX7219 chip - Led 3mm red color - SPI communication - Voltage: 4.7 - 5.3V DC - Interfaces to manage multiple modules in cascade - Matrix dimensions: 32mm x 32mm x 8mm - PCB dimensions: 32mm x 50mm Code M0043 Available Price €2.95
TDA2030A 1X18W Audio Amplifier TDA2030A 1X18W Audio Amplifier features: - Chip: TDA2030A - Power supply: DC 6V ~ 12V - Channel type: Single channel - Output power: 1 x 18 W - Output output: 4 ~ 8 Ohm - Mono mode - Size (LxWxH): 31.6 x 23.5 mm Code M0063 Available Regular price €3.39 -€1.00 Price €2.39
NFC RFID Keychain Tag 13.56 MHz NFC RFID Keychain Tag 13.56 MHz features: - 32 bit unique code - Protocol: ISO14443 - Compatible with NFC Mifare 1k - Memory: 1kB EEPROM - Operating frequency: 13.56MHZ - Communication speed: 106Kboud - Reading distance: 2.5-10CM - Reading time: 1-2MS - Working temperature: -20ºC to 85ºC - Number of uses 100,000 times - Data retention: 10 years - Material: ABS - Dimensions 40.5 x 32 x 4.2 mm Code M0030 Available Price €0.99
NFC RFID Tag Card 13.56 MHz NFC RFID Tag Card 13.56 MHz can be used in Access Control projects and Alarm, Arduino, Raspberry PI, PIC, AVR projects. Code M0033 Available Price €0.99
TDA7498 Class D 2X100W Amplifier Characteristic: - Quiescent current: 50 mA (without load) - Efficiency: 90% - Nominal output power max.: 2 x 100W - Frequency response: 20Hz to 20KHz - Operating voltage: DC20V to DC34V - Recommended supply voltage: DC32V - Speaker parameters: 6 Ohm , 8 Ohm - PCB board size: 87 × 72 mm - Package includes cable Code M0035 ✗ Out-of-Stock Price €19.51
Bluetooth Transceiver Module HC-06 Wireless HC-06 Bluetooth transceiver module with base.The bluetooth module HC-06 is one of the best options for projects, in which you need wireless communications.The transceiver module allows bluetooth wireless connections as a slave, ready to listen for connection requests. Bluetooth Transceiver Module HC-06 Wireless features: - Chipset CSR BC417- 3.5V - 5V power- Bluetooth version V2.0 + EDR- Frequency: 2.4GHz ISM band- Modulation: GFSK- Reach approx. 10m- Security: Authentication and encryption.- Speed-> Asynchronous: 2.1Mbps (Max) / 160 kbps; Synchronous: 1Mbps / 1Mbps- Supports AT commands for configuration through a serial port- Working temperature: -20ºC to + 75ºC- Working current - pairing: 80 mA Code W0009 Available Price €5.39
USB DC 5V Bluetooth Audio USB DC 5V Bluetooth Audio features: - You can connect it with your smartphone - Power: DC 5V micro USB - Speaker: 4 ~ 8 Ohm - Audio Jack: 3.5mm - SD card: support MP3 / WMA / WAV / FLAC format - The transmission distance could be up to 10m - Size: 50 x 40 mm Code M0067 ✗ Out-of-Stock Price €5.79
ESP-12F ESP8266 12F WiFi Board Module - WIFI module based on the ESP8266 controller- ESP8266-12F is an improved version of ESP8266-12E- It works as a standard WiFi 802.11 b / g / n 2.4 GHz. It is equipped with 22 outputs (pitch 2 mm) of which 11 are GPIO, ADC 1 and SPI. A LED and a PCB antenna have been incorporated ESP-12F ESP8266 12F WiFi Board Module features: - Supply voltage: 3.3V (LOGICAL LEVELS: 3.3V)- Supported protocols: 802.11 b / g / n- Network support: 2.4 GHz- Band: 2400 (MHz)- Wi-Fi Direct (P2p), Soft Access Point- Integrated TCP / IP Stack.- PLL, regulators and integrated energy management units- Output power: 0.15 (W); + 19.5dBm in 802.11b mode- Consumption in low energy mode: <10 uA- Integrated 32-bit processor Code W0064 Available Price €3.09
PAM8403 2x3W Digital Amplifier Channel Stereo PAM8403 2x3W Digital Amplifier Channel Stereo features: - Up to 3W in each channel- Chip: PAM8403- Power supply: 5V- Power: 2 outputs of 3 watts each- Measures: 21x18 mm- Suitable impedance speakers: 4 Ohm Code M0027 Available Price €1.89
Bluetooth Transceiver Module HC-05 Wireless - HC-05 Bluetooth transceiver module with base- The bluetooth module HC-05 is one of the best options for projects where you need wireless communications.- The transceiver module (transmission / reception) allows bluetooth wireless connections like master or slave, works in a transparent way as if we made a RS-232 TTL serial connection with cable.Bluetooth Transceiver Module HC-05 Wireless features:- Chipset CSR BC417- 3.6 to 6 Vdc power supply- Bluetooth version V2.0 + EDR- Frequency: 2.4GHz ISM band- Modulation: GFSK- Reach approx. 10m- Security: Authentication and encryption.- Speed-> Asynchronous: 2.1Mbps (Max) / 160 kbps; Synchronous: 1Mbps / 1Mbps Code W0004 Available Price €5.39
Edup Mini Dongle WiFi USB For pcDuino 3 Nano Raspberry Pi Edup Mini Dongle WiFi USB For pcDuino 3 Nano Raspberry Pi features: - Interface type: USB - Supports IEEE 802.11e draft 802.11n - Supports USB 2.0, compatible with USB 1.1 and 1.2 - Support systems: - Win2k / XP / Vista / Win7 / Win8.1 / Win10 / Mac / Linux - Operating distance: 91 meters indoors, 275 meters in open space - Transfer rate: 150Mbps (downlink) and 150Mbps (uplink) - Works with old Wireless-G and Wireless-B networks - WEP and WPA encryption - 64-bit / 128-bit WEP (Wired Equivalent Privacy), TKIP, AES 2,400GHz ISM - Frequency range: 2.4 to 2.4835 GHz - Operating channels: 13 - Support network protocol: CSMA / CA with acknowledgment - Transmission mode: DSSS Code RA015 Available Regular price €8.49 -€2.00 Price €6.49
Transducer Bone conduction 8 Ohm Speaker 1 Watt Wired Bone Conductor Transducer - 8 Ohm 1 Watt This amazing speaker does not have a movable cone like most From the speakers you've seen, instead, a small metal rod is wrapped with the voice coil. When the current is driven through the coil, the magnetic field makes a piece of metal expands and contracts, if pressed against a flat surface or cavity makes it a speaker! Often these size transducers are pressed against the jaw or ear bone to turn the skull into a speaker socket. The effect is a perfect quality sound that comes from your head and no one else can hear it. You can also press it against your elbow bone and stick a finger in your ear to listen to the audio transmitted through your arm! Code M0113 ✗ Out-of-Stock Price €14.95
MAX98306 3.7W Stereo Amplifier MAX98306 3.7W Stereo Amplifier - Class D Stereo Audio Amplifier 8 Ohm. Code M0117 ✗ Out-of-Stock Price €14.79
Wireless Module AT-09 Bluetooth 4.0 CC2541 IOS BLE - Bluetooth 4.0 AT-09 BLE Master / Slave module with 6-pin connection base - This module is very similar to HM-10 module - Bluetooth protocol: Bluetooth V4.0 BLE specification - Ultra-low power consumption, in 90uA standby mode Wireless Module AT-09 Bluetooth 4.0 CC2541 IOS BLE features: - Chipset based on CC2541 - Bluetooth Class 2 - Industrial level Bluetooth module SPP - Flash 256Kb - Integrated chip antenna - Power supply: + 3.3 VDC 50 mA - Working temperature: -5 C to + 60 C - Operating frequency: 2.4 GHz ISM Band - Modulation method: GFSK (Gaussian Frequency Shift keying) Code W0078 Available Price €4.95
Bluetooth Decoder Module Amplifier Audio Receiver USB TF This module has three modes (control, music and bluetooth). The audio files can be saved on the U disk and on the TF card.Its remote control allows you to control the audio output (volume down or up, music change, mode change). Bluetooth Decoder Module Amplifier Audio Receiver USB TF features: - Interfaces: - 5V micro USB supply - USB audio - U disk - LED - TF card - IR remote - AD key interface to connect external circuits - Bluetooth decoder - 3.5mm stereo output - Left and right 3W channels handling speaker - 2 3W amplifiers- Supply voltage: 3.7-5VDC- Signal / noise ratio (SNR): 90 dB Code W0084 Last items in stock Price €5.90
Module Relay 5V Light sensor LDR photoresistor This module is a three way switch ( COM, NO and NC ) that uses the intensity of the ambient light to control directly the load at the output. Its adjustment potentiometer allows changing the sensitivity and setting the start threshold of the relay. The relay is energized when it is darker than the threshold. Code RL016 Available Price €2.39
Raspberry Pi 2-3 Model B Multifunction Expansion GPIO Module This module is used to extend the Raspberry's 40 GPIO pins to another set of 2x20 male pins and 8 parallel pins accessible on the terminal blocks in the that test leads are pushed. The electronic board offers great reliability with the Raspberry and is very easy to connect thanks to its existing suitable accessories but not included. The module offers a set of mini jumpers to configure the GPIO. Code RA016 Available Price €7.95
Wireless Transceiver Module with Antenna CC1101 This external wireless antenna module CC1101 is suitable for Funduino and Arduino projects.The CC1101 module of 1.2K baud consists of a domestic R & Lotes unit to improve the effective communication distance.This is a significant improvement over the CC1100 module.It allows to adjust the speed of the bits for different uses, thus allowing a higher transmission speed.Supports 2-FSK, GFSK and msk modulations. It also has a high sensitivity (1.2kbps @> Code W0083 Available Price €8.49
Full Color SMD LED Module RGB KY-009 This module specially designed for Arduino will allow you to generate a light of any color (RGB) quickly and accurately. The SMD LED Module RGB, consisting of an LED capable of creating any color using RGB, has a PWM voltage input with three pins. These are capable of shining in a wide range of colors thanks to the mixture of the three primary colors (red , green and blue). These types of diodes are called RGB and are made up of three red, green and blue diodes in the same package. Thanks to the variation of the intensity of these three diodes, we can create a composition of colors. With this led you can handle more than 16.5 million colors. Code M0080 Available Price €2.95
LED Module Full Color RGB Bulb KY-016 This module specially designed for Arduino will allow you to generate a light of any color (RGB) quickly and accurately. The LED Bulb Module RGB, consisting of an LED capable of creating any color using RGB, has a PWM voltage input with three pins. These are capable of shining in a wide range of colors thanks to the mixture of the three colors. primary (red, green and blue). These types of diodes are called RGB and are made up of three red, green and blue diodes in the same package. Thanks to the variation of the intensity of these three diodes, we can create a composition of colors. With this led you can handle more than 16.5 million colors. Code M0081 Available Price €2.95
Lilypad LED Blue Blue LED.The color option allows you to adjust the LEDs to your liking to sew clothes or anything else you can dream of.Lilypad is a wearable E-textile technology developed to have large connection pads to attach to clothing. Lilypad LED Blue features: - Operating voltage: 3 - 5 VDC- Very bright- Density of the PCB: 0.8 mm- LED color: blue- Size: 5.5x12.5 mm- 1 LED included Code M0137 Available Regular price €0.99 -€0.20 Price €0.79
Lilypad LED Red LED of red color.The color option allows you to adjust the LEDs to your liking to sew clothes or anything else you can dream of.Lilypad is a wearable E-textile technology developed to have large connection pads to attach to clothing. Lilypad LED Red features: - Operating voltage: 3 - 5 VDC- Very bright- Density of the PCB: 0.8 mm- LED color: red- Size: 5.5x12.5 mm- 1 LED included Code M0138 Last items in stock Price €0.99
Lilypad LED Green LED green.The color option allows you to adjust the LEDs to your liking to sew clothes or anything else you can dream of.Lilypad is a wearable E-textile technology developed to have large connection pads to attach to clothing. Lilypad LED Green features: - Operating voltage: 3 - 5 VDC- Very bright- Density of the PCB: 0.8 mm- LED color: green- Size: 5.5x12.5 mm- 1 LED included Code M0139 Last items in stock Price €0.99
Lilypad Button Board This support is a lilypad button to sew clothing or anything else you can dream of.Lilypad is a wearable E-textile technology developed to have large connection pads to attach to clothing. Lilypad Button Board features: - Density of the PCB: 0.8 mm- Size: 8x16 mm- 1 LED included Code M0142 Available Regular price €0.99 -€0.20 Price €0.79
Lilypad Power Supply 5V Step Up with AAA Batteries This module is a small source of energy, this board was designed to be as small and as indiscreet as possible.Putting a battery type AAA and operating the power switch, will have a supply of 5 V to power a lilypad circuit.Use up to 200ma, it is protected against short circuits. This card has AAA battery clips but can use a 1.2V to 5V input, the module increases the voltage up to 5V.Lithium polymer batteries are an alternative to rechargeable batteries.Lilypad is a wearable E-textile technology developed to have large connection pads to attach to clothing. Lilypad Power Supply 5V Step Up with AAA Batteries features: - Type of batteries connectable: AAA- Input voltage (of the batteries): from 1.5V to 5V- Output voltage: 5V Code M0140 Available Regular price €7.99 -€2.50 Price €5.49
Lilypad Slide Switch Board 2 Positions Interruptor This is a simple slide switch for LilyPad. Use it as a simple On / Off switch, or to control LEDs, buzzers, sensors, etc.The switches in each panel have a capacity of 4V to 300 mA, but will operate at 5V with a current reduction.Lilypad is a wearable E-textile technology developed to have large connection pads to attach to clothing. Lilypad Slide Switch Board 2 Positions Interruptor features: - Switch two positions: On (ON) / Off (OFF)- Density of the PCB: 0.8 mm- Size: 7.75x18.1 mm Code M0141 Available Regular price €1.99 -€0.50 Price €1.49
Lilypad Tri-Color LED RGB Blink any color you need! Use the Tri-Color LED board as a simple indicator, or by pressing the red, green and blue channels, you can create any color. Very bright output.This is a common anode design: to turn on a channel, you simply need to ground one of the R / G / B pins to illuminate that channel.Lilypad is a wearable E-textile technology developed to have large connection pads to attach to clothing. Lilypad Tri-Color LED RGB features: - Operating voltage: 3 - 5 VDC- Design of common anode- Density of the PCB: 0.8 mm- Outside diameter: 20 mm Code M0143 Available Regular price €1.49 -€0.30 Price €1.19
Lilypad Buzzer The buzzer plate for Lilypad is used for the development and application of configurations that require a buzzer to indicate, for example, warnings, warnings or as part of the correct operation of your device.Lilypad is a wearable E-textile technology developed to have large connection pads to attach to clothing. Lilypad Buzzer features: - Operating voltage: 5 VDC- Design of common anode- PCB density: 0.5 mm- Density of the buzzer: 20 mm- Outside diameter: 20 mm Code M0144 Available Regular price €2.00 -€0.50 Price €1.50
Pixel Board WS2812 for Lilypad The pixel board is equipped with a WS2812 that is actually RGB LED with a WS2811 built into the LED.Several of these individual sessions can be chained together to form a screen or an addressable string.Each LilyPad is creatively designed to have large connecting pads so that they can be sewn on clothes. Pixel Board WS2812 for Lilypad features:- Use the WS2812S chip- RGB color lights- Each LED can be controlled individually- You only need one control line and two power cables- Arduino libraries and routines available- Density of the PCB: 0.8 mm- Size: 20x3 mm Code M0146 Available Regular price €6.79 -€2.00 Price €4.79
LiPower Battery Booster Module 5V Output Lilypad The good thing about LiPower is the ability to use rechargeable lithium polymer batteries.These batteries are smaller, flatter and last much longer than an AAA battery.Connect a single-cell LiPo battery, turn on the power switch and you will have a 5V supply to power your LilyPad network. It can deliver the current up to 150mA. Protected against the short circuit.This board has a JST connector, which will be connected to single cell LiPo batteries terminated in JST.It also has terminals for charging the LiPo battery with LiPo chargers. Each LilyPad was creatively designed to have large connection pads that allow them to sew on clothes. Code M0148 Available Regular price €7.99 -€1.00 Price €6.99
Expansion Module I/O XBEE This XBEE module contains everything you need to create your projects, including socket to mount an XBee device, VDC power pins, GND, terminal block to power a servo motor, reset button and much more. The new expansion IO Shield V7.1 offers several advantages and these are its characteristics.Compatible with the new Arduino Due. Code M0150 Available Price €8.49