Transducer Bone conduction 8 Ohm Speaker 1 Watt

Shield Li-Po Battery for WeMos D1 Mini ESP826 features:
Connect the lithium battery to this shield to supply power for the entire D1 mini system.
When the battery is depleted, it is not necessary disconnect the battery, just use the usb port to charge directly. - Charging voltage: max: 10V, recommend: 5V
- Charging current: max: 1A
- Voltage lithium battery: 3.3-4.2V
- Boost power supply: 5V (max: 1 A)
- LED color: red for charging, green for fully charged
- Ports:
* Micro USB - Charging port (normal 5V)
* Connect to the lithium battery (normal 3.3-4.2V)
* J1 - setting the maximum charging current, 0.5 A or 1A

The DC-DC 25A solid state relay has a 3-32VDC input and a 6-60VDC output. It has a maximum load capacity of 25A.
It has a long operating life and high reliability, a compact size. This relay switches very quickly. Fotek SSR-25 DD 25A DC-DC Solid State Relay 5V-60VDC output 

- WIFI module based on the ESP8266 controller
- ESP8266-12F is an improved version of ESP8266-12E
- It works as a standard WiFi 802.11 b / g / n 2.4 GHz. It is equipped with 22 outputs (pitch 2 mm) of which 11 are GPIO, ADC 1 and SPI. A LED and a PCB antenna have been incorporated
ESP-12F ESP8266 12F WiFi Board Module features:
- Supply voltage: 3.3V (LOGICAL LEVELS: 3.3V)
- Supported protocols: 802.11 b / g / n
- Network support: 2.4 GHz
- Band: 2400 (MHz)
- Wi-Fi Direct (P2p), Soft Access Point
- Integrated TCP / IP Stack.
- PLL, regulators and integrated energy management units
- Output power: 0.15 (W); + 19.5dBm in 802.11b mode
- Consumption in low energy mode: <10 uA
- Integrated 32-bit processor

This 1-meter probe uses the original DS18B20 temperature sensor chip. The DS18B20 is a waterproof temperature sensor/thermometer. It is waterproof, moisture proof and rustproof with the high quality stainless steel tube encapsulated. This is a spare part or accessory used in SONOFF TH10 / TH16.

Buzzer alarm to convert electrical to acoustic signals in robotics devices and Arduino projects.
Buzzer 5V Active Buzzer 4 to 7V DC features:

- Input voltage: 4V to 7V
- Diameter: 12mm
- Height: 9.5mm
- Spacing Pins: 7.6mm
- Maximum Current:

NodeMcu module based on ESP8266 controller and programming in Lua language.
NodeMcu is equipped with 10 GPIO, PWM, I2C, 1-wire and ADC.
ESP8266-12E is an improved version of ESP8266-12.
It works as a standard WiFi 802.11 b / g / n 2.4 GHz.
USB communication - the CH340 chip. Characteristics of ESP 12E:
- Supply voltage: 3.3V (LOGICAL LEVELS: 3.3V)
- Supported protocols: 802.11 b / g / n
- Network support: 2.4 GHz
- Band: 2400 (MHz)
- Wi-Fi Direct (P2p), Soft Access Point
- TCP Stack / Integrated IP
- PLLs, Regulators and Integrated Power Management Units
- Output Power: 0.15 (W); + 19.5dBm in 802.11b mode

You can easily control any device over the Internet through your phone, computer, etc.
The module can handle 5 users at the same time, it can work in two modes: STA (client) and AP (access point).
In AP mode, the module is connected via WIFI directly to your phone or computer (in open field can be up to 300 meters).
In STA mode, the relay module is connected to the access point (router) that supplies the network.
Wi-Fi in the room where the relays are located. In this case, the range mainly depends on the power of the access point antennas (routers).
You should not turn off after the configuration is completed, as some of the parameters of the WIFI module cannot be saved when power is cut off.

This capacitive touch sensor module uses the TTP229 integrated circuit, making it easy to add capacitive touch input to your project. Capacitive Touch Sensor Module TTP229 - 16 Touch Sensitive Pads 

 Master Slave Bluetooth Modul for Arduino iOS Android. The HM10 supports Bluetooth 4.0 (low energy) and therefore has a relatively low power consumption.