4x4 High Quality Keyboard Matrix Push Buttons 16 Touch Keys High quality keyboard, with 16-key matrix.Ideal for your arduino projects, but can also be used with other microcontrollers. 4x4 High Quality Keyboard Matrix Push Buttons 16 Touch Keys features: - Momentary contact- Number of push buttons: 16- Dimensions: 39mm x 43mm Code M0009 Available Price €1.23
BC547B NPN 50V 100mA transistor 0.1A TO-92 Product Category: Bipolar Transistor, NPN. BC547B NPN 50V 100mA transistor 0.1A TO-92 features: - Package / Case: TO-92 - Quantity: 25 units - Collector-base voltage VCBO: 50V - Collector-emitter voltage VCEO: 45V - VEBO emitter-base voltage: 6V - Continuous collector current: 100mA - DC MAX collector current: 200mA - Maximum power dissipation: 500mW Code T0043 Backorder Price €0.03
Infrared LED Flame Sensor 5mm Led infrared sensor.Detector of the source of fire or flame, can detect a flame or wavelength 760 nm-1100 nmParticularly sensitive to the flame spectrum.This optical flame sensor is a device that detects the existence of combustion by the light emitted by it. Infrared LED Flame Sensor 5mm features: - Range of light, Distance of 80 cm.- Angle detection of about 60 degrees,- This light can be detected by an optical sensor,- Can be captured by digital inputs and analog inputs of Arduino. Code S0132 Available Price €0.37
ESP8266 WIFI Module ESP-01 for Electronic Sensor Robotics WIFI transceiver based on the ESP8266 controller. It has a microcontroller and 2 GPIO pins to be able to operate autonomously without the need for an external microcontroller. Characteristic: - Voltage of power: 3.3V - Supported protocols: 802.11 b / g / n - Network support: 2.4 GHz - Band: 2400 (MHz) - Wi-Fi Direct (P2p), Soft Access Point - Integrated TCP / IP stack - PLL, regulators and integrated power management units - Output power: 0.15 (W); + 19.5dBm in 802.11b mode - Consumption in low power mode: Code W0003 Available Price €1.61
NEC IR Remote Control Infrared emitter HX1838 Arduino Raspberry Remote Control HX1838 Infrared Emitter NEC IR Remote Control Infrared emitter HX1838 features: - 21 keys - Measurements 85x 40x 5mm - Includes battery Useful links for Arduino / Raspberry programming and projects with Arduino / Raspberry boards: Send / Receive information via IR - Wiring of the IR Remote control + Infrared IR Receiver VS1838 with UNO module - Lighting a red 3mm LED by Infrared Realization of a manageable Infrared robot - Wiring the IR Distance remote control + Infrared IR Receiver VS1838 with the UNO module - Fix the IR Distance remote control + VS1838 Infrared IR Receiver in a Mini 2WD DIY Car Robot Kit Code W0020 Available Price €0.81
SW-520D Vibration Metal Tilt Sensor Detects changes in the sensor angle and returns to the digital value. 5x SW-520D Vibration Metal Tilt Sensor features: - Contact resistance: Code S0020 Available Price €0.37
USB Cable A to Micro USB B for Arduino Leonardo, Due USB Cable A to Micro USB B Arduino Leonardo, Due features: - Color: Blue or black- Length: 50cm Code K0161 Available Price €1.31
Bluetooth Transceiver Module HC-06 Wireless HC-06 Bluetooth transceiver module with base.The bluetooth module HC-06 is one of the best options for projects, in which you need wireless communications.The transceiver module allows bluetooth wireless connections as a slave, ready to listen for connection requests. Bluetooth Transceiver Module HC-06 Wireless features: - Chipset CSR BC417- 3.5V - 5V power- Bluetooth version V2.0 + EDR- Frequency: 2.4GHz ISM band- Modulation: GFSK- Reach approx. 10m- Security: Authentication and encryption.- Speed-> Asynchronous: 2.1Mbps (Max) / 160 kbps; Synchronous: 1Mbps / 1Mbps- Supports AT commands for configuration through a serial port- Working temperature: -20ºC to + 75ºC- Working current - pairing: 80 mA Code W0009 Available Price €4.45
Pixel Board WS2812 for Lilypad The pixel board is equipped with a WS2812 that is actually RGB LED with a WS2811 built into the LED.Several of these individual sessions can be chained together to form a screen or an addressable string.Each LilyPad is creatively designed to have large connecting pads so that they can be sewn on clothes. Pixel Board WS2812 for Lilypad features:- Use the WS2812S chip- RGB color lights- Each LED can be controlled individually- You only need one control line and two power cables- Arduino libraries and routines available- Density of the PCB: 0.8 mm- Size: 20x3 mm Code M0146 Available Regular price €5.61 -€2.00 Price €3.61
RFID Module with Card and Pendant It is compatible with almost any microcontroller, Arduino, PIC, AVR.It can be used in Access Control projects and Alarm projects. RFID Module with Card and Pendant features: - Supports Quick CRYPTO1 and MIFARE- Operating current: 13-26mA at 3.3V- Standby current: 10-13mA to 3.3V- Sleep-mode current: <80μA- Maximum current: 30mA- Frequency of operation: 13.56Mhz- Reading distance: 0 to 60mm- Communication protocol: SPI- Maximum SPI speed: 10Mbit / s- Maximum data rate: 10Mbit / s- Operating temperature: -20 to 80ºC- Humidity of operation: 5% -95% Code M0015 Available Price €2.31
Raspberry Pi v2 NoIR Oficial Camera - Sony IMX219 8 Megapixel Sensor Raspberry Pi HD Pi NoIR V2 camera board Raspberry Pi HD Pi NoIR camera board connects to any Raspberry Pi or Compute Module to create HD photos and video. The Pi NoIR (without infrared) is the same as the standard camera module but without an infrared filter. Therefore, it is excellent for photography and video in the dark. The module uses Sony's IMX219PQ image sensor that offers high-speed, high-sensitivity video images. The Pi NoIR module offers contamination from Reduced image such as fixed pattern noise and smudges. It also has automatic control functions such as exposure control, white balance and luminance detection. Raspberry Pi NoIR Camera Board, Sony IMX219 8 Megapixel Sensor features: and benefits: No infrared filter High quality images Code RA054 Last items in stock Price €24.70
Mini vibration engine for Arduino and Raspberry Pi 5 VDC This mini vibration motor runs on 5 VDC and can be used for Arduino and Raspberry projects. It is a direct current motor. Mini vibration engine for Arduino and Raspberry Pi 5 VDC features: - Voltage: 5 VDC, - Current: 75mA, - Rotation speed: 1100 (rpm), - Efficiency: 80%, - Dimensions: 10x27mm. Code M0174 Available Price €0.83
Relay SRD-12 DC-2P 12V 10A SPDT Relay SRD-12 DC-2P 12V 10A SPDT features:- Supply voltage: 12V- Output Current: 10A- Relay activation current: 15mA ~ 20mA- For power switching with 12V DC signals - Microcontroller, Arduino, Electronica Code RL012 Available Price €0.81
ESP8266 ESP12E WiFi NodeMcu + Motor Drive L293D Expansion Shield Board Kit NodeMcu module based on ESP8266 controller and programming in Lua language. NodeMcu is equipped with 10 GPIO, PWM, I2C, 1-wire and ADC. ESP8266-12E is an improved version of ESP8266-12. It works as a standard WiFi 802.11 b / g / n 2.4 GHz. USB communication - the CP2102 chip. Characteristic of ESP 12E: - Supply voltage: 3.3V (LOGICAL LEVELS: 3.3V), - Supported protocols: 802.11 b / g / n, - Network support: 2.4 GHz, - Band: 2400 (MHz), - Wi-Fi Direct (P2p), Soft Access Point, - TCP Stack / Integrated IP, - PLLs, Regulators and Integrated Power Management Units, - Output Power: 0.15 (W); + 19.5dBm in 802.11b mode, Code W0016 Available Price €6.98
M12 High Resolution Lens, 5MP, 20.2° FOV, 25mm Focal length, Compatible with Raspberry Pi High Quality Camera M12 M12 Long Focal Length Lens, 5MP, Long Focal Length 25mm, F1.7 Large Aperture, Compatible with Raspberry Pi High Quality Camera M12 Code WV014 Available Price €18.97
TDA2030A 1X18W Audio Amplifier TDA2030A 1X18W Audio Amplifier features: - Chip: TDA2030A - Power supply: DC 6V ~ 12V - Channel type: Single channel - Output power: 1 x 18 W - Output output: 4 ~ 8 Ohm - Mono mode - Size (LxWxH): 31.6 x 23.5 mm Code M0063 Available Regular price €2.80 -€1.00 Price €1.80
ESP-12F ESP8266 12F WiFi Board Module - WIFI module based on the ESP8266 controller- ESP8266-12F is an improved version of ESP8266-12E- It works as a standard WiFi 802.11 b / g / n 2.4 GHz. It is equipped with 22 outputs (pitch 2 mm) of which 11 are GPIO, ADC 1 and SPI. A LED and a PCB antenna have been incorporated ESP-12F ESP8266 12F WiFi Board Module features: - Supply voltage: 3.3V (LOGICAL LEVELS: 3.3V)- Supported protocols: 802.11 b / g / n- Network support: 2.4 GHz- Band: 2400 (MHz)- Wi-Fi Direct (P2p), Soft Access Point- Integrated TCP / IP Stack.- PLL, regulators and integrated energy management units- Output power: 0.15 (W); + 19.5dBm in 802.11b mode- Consumption in low energy mode: <10 uA- Integrated 32-bit processor Code W0064 Available Price €2.55
8 Channel 5V 10A Relay Module Arduino compatible 5V Relay Module with 8 opto-coupled channels. This module can be directly controlled by the microcontroller ( Arduino, 8051, AVR, PIC, DSP, ARM, ARM, MSP430, TTL). 8 Channel Arduino 5V 10A Relay Module features: - Channels: 8 (independent protected with Optocouplers) - Supply Voltage: 5V - Output Current: 10A - Relay activation current: 15mA ~ 20mA - Isolation: Yes - LED indicator: For each channel - Dimensions: 54x 135mm Code RL008 Available Price €7.84
Pixel Board WS2812 for Lilypad The pixel board is equipped with a WS2812 that is actually RGB LED with a WS2811 built into the LED.Several of these individual sessions can be chained together to form a screen or an addressable string.Each LilyPad is creatively designed to have large connecting pads so that they can be sewn on clothes. Pixel Board WS2812 for Lilypad features:- Use the WS2812S chip- RGB color lights- Each LED can be controlled individually- You only need one control line and two power cables- Arduino libraries and routines available- Density of the PCB: 0.8 mm- Size: 20x3 mm Code M0146 Available Regular price €5.61 -€2.00 Price €3.61
RFID Module with Card and Pendant It is compatible with almost any microcontroller, Arduino, PIC, AVR.It can be used in Access Control projects and Alarm projects. RFID Module with Card and Pendant features: - Supports Quick CRYPTO1 and MIFARE- Operating current: 13-26mA at 3.3V- Standby current: 10-13mA to 3.3V- Sleep-mode current: <80μA- Maximum current: 30mA- Frequency of operation: 13.56Mhz- Reading distance: 0 to 60mm- Communication protocol: SPI- Maximum SPI speed: 10Mbit / s- Maximum data rate: 10Mbit / s- Operating temperature: -20 to 80ºC- Humidity of operation: 5% -95% Code M0015 Available Price €2.31
Raspberry Pi v2 NoIR Oficial Camera - Sony IMX219 8 Megapixel Sensor Raspberry Pi HD Pi NoIR V2 camera board Raspberry Pi HD Pi NoIR camera board connects to any Raspberry Pi or Compute Module to create HD photos and video. The Pi NoIR (without infrared) is the same as the standard camera module but without an infrared filter. Therefore, it is excellent for photography and video in the dark. The module uses Sony's IMX219PQ image sensor that offers high-speed, high-sensitivity video images. The Pi NoIR module offers contamination from Reduced image such as fixed pattern noise and smudges. It also has automatic control functions such as exposure control, white balance and luminance detection. Raspberry Pi NoIR Camera Board, Sony IMX219 8 Megapixel Sensor features: and benefits: No infrared filter High quality images Code RA054 Last items in stock Price €24.70
Mini vibration engine for Arduino and Raspberry Pi 5 VDC This mini vibration motor runs on 5 VDC and can be used for Arduino and Raspberry projects. It is a direct current motor. Mini vibration engine for Arduino and Raspberry Pi 5 VDC features: - Voltage: 5 VDC, - Current: 75mA, - Rotation speed: 1100 (rpm), - Efficiency: 80%, - Dimensions: 10x27mm. Code M0174 Available Price €0.83
Relay SRD-12 DC-2P 12V 10A SPDT Relay SRD-12 DC-2P 12V 10A SPDT features:- Supply voltage: 12V- Output Current: 10A- Relay activation current: 15mA ~ 20mA- For power switching with 12V DC signals - Microcontroller, Arduino, Electronica Code RL012 Available Price €0.81
ESP8266 ESP12E WiFi NodeMcu + Motor Drive L293D Expansion Shield Board Kit NodeMcu module based on ESP8266 controller and programming in Lua language. NodeMcu is equipped with 10 GPIO, PWM, I2C, 1-wire and ADC. ESP8266-12E is an improved version of ESP8266-12. It works as a standard WiFi 802.11 b / g / n 2.4 GHz. USB communication - the CP2102 chip. Characteristic of ESP 12E: - Supply voltage: 3.3V (LOGICAL LEVELS: 3.3V), - Supported protocols: 802.11 b / g / n, - Network support: 2.4 GHz, - Band: 2400 (MHz), - Wi-Fi Direct (P2p), Soft Access Point, - TCP Stack / Integrated IP, - PLLs, Regulators and Integrated Power Management Units, - Output Power: 0.15 (W); + 19.5dBm in 802.11b mode, Code W0016 Available Price €6.98
M12 High Resolution Lens, 5MP, 20.2° FOV, 25mm Focal length, Compatible with Raspberry Pi High Quality Camera M12 M12 Long Focal Length Lens, 5MP, Long Focal Length 25mm, F1.7 Large Aperture, Compatible with Raspberry Pi High Quality Camera M12 Code WV014 Available Price €18.97
TDA2030A 1X18W Audio Amplifier TDA2030A 1X18W Audio Amplifier features: - Chip: TDA2030A - Power supply: DC 6V ~ 12V - Channel type: Single channel - Output power: 1 x 18 W - Output output: 4 ~ 8 Ohm - Mono mode - Size (LxWxH): 31.6 x 23.5 mm Code M0063 Available Regular price €2.80 -€1.00 Price €1.80
ESP-12F ESP8266 12F WiFi Board Module - WIFI module based on the ESP8266 controller- ESP8266-12F is an improved version of ESP8266-12E- It works as a standard WiFi 802.11 b / g / n 2.4 GHz. It is equipped with 22 outputs (pitch 2 mm) of which 11 are GPIO, ADC 1 and SPI. A LED and a PCB antenna have been incorporated ESP-12F ESP8266 12F WiFi Board Module features: - Supply voltage: 3.3V (LOGICAL LEVELS: 3.3V)- Supported protocols: 802.11 b / g / n- Network support: 2.4 GHz- Band: 2400 (MHz)- Wi-Fi Direct (P2p), Soft Access Point- Integrated TCP / IP Stack.- PLL, regulators and integrated energy management units- Output power: 0.15 (W); + 19.5dBm in 802.11b mode- Consumption in low energy mode: <10 uA- Integrated 32-bit processor Code W0064 Available Price €2.55
8 Channel 5V 10A Relay Module Arduino compatible 5V Relay Module with 8 opto-coupled channels. This module can be directly controlled by the microcontroller ( Arduino, 8051, AVR, PIC, DSP, ARM, ARM, MSP430, TTL). 8 Channel Arduino 5V 10A Relay Module features: - Channels: 8 (independent protected with Optocouplers) - Supply Voltage: 5V - Output Current: 10A - Relay activation current: 15mA ~ 20mA - Isolation: Yes - LED indicator: For each channel - Dimensions: 54x 135mm Code RL008 Available Price €7.84