6 V Peristaltic Submersible Mini Pump

Buzzer 5V Passive 5 to 12V DC features:
- Input voltage: 4V to 12V
- Diameter: 17mm
- Height: 7mm
- f = 4kHz +/- 500
- Pin Separation: 10mm
- Maximum Current:

NFC Card Type 2 NTAG215 RFID Dual Label 13.56 MHz features:
- Standard: NFC Forum Type2 Tag Ntag215
- Protocol: ISO14443A
- Memory: 540B (504B) EEPROM - Operating frequency: 13.56MHZ
- Reading distance: 0-10CM
- Communication speed: 106Kboud
- Working temperature: -20ºC to 70ºC
- Number of uses 100,000 times
- Data retention: 10 years
- Material: PVC
- Dimensions 86 x 54 x 0.84 mm

A waterproof pentaband antenna X000016  for all your wireless projects with Arduino and development boards

Amplifier for speakers, especially for cars, dual channel and with subwoofer. It operates at 12/24V and offers an output power of 50W for each channel + 100W subwoofer. Create your 2.1 speaker system with this amplifier.

Buzzer alarm to convert electrical signals into intermittent acoustic signals in robotic devices and Arduino projects

A buzzer with a pulsating tone generator, after connecting the supply voltage (DC) in the range of 3V -24V, the buzzer generates an intermittent signal with a frequency of approximately 1 Hz. Application example: as a reverse alarm system for a car. 

Relay SRD-05 DC-2P 5V 10A SPDT features:
- Supply voltage: 5V
- Output Current: 10A
- For power switching with 5V DC signals - Microcontroller, Arduino, Electronica

This XBEE module contains everything you need to create your projects, including socket to mount an XBee device, VDC power pins, GND, terminal block to power a servo motor, reset button and much more. The new expansion IO Shield V7.1 offers several advantages and these are its characteristics.
Compatible with the new Arduino Due.

GSM A6 Four Band GPRS Module with MCU Antenna features:
- GSM / GPRS module / development board / shield based on GPRS A6
- Supports GSM / Dual band GPRS, available for remote GPRS and SMS data transmission
- Compact size and low current consumption
- With energy saving technique, current consumption is as low as 5mA (sleep mode)
- Communicates with the microcontroller through the UART port, supports the command including GSM 07.07, GSM 07.05 and Ai-Thinker Enhanced AT Commands
- Working frequency: four-band network, 850 / 900/1800 / 1900MHz
- Operating voltage: 4.8-9VDC (Supply power of the on-board regulator circuit for the A6 module)
- Working current: 2A maximum
- Current Sleep: 5mA

It is ultra compact and very low consumption. It works at 2.4GHz frequencies (free frequency) and is ideal for telemetry projects, robots, peripheral control, video game control applications, remote temperature sensors, pressure, alarms, etc ... NRF24L01 + Wireless Transceiver Module 2.4GHz features:
- Based on chip NRF24L01 + Ultra Low Power
- Free band: 2.4GHz ISM
- Speed: 250kbps, 1Mbps, 2Mbps
- Working current - reception: 13 mA
- Transmission: 11 mA (900nA -deep sleep mode)
- Receiving sensitivity: -94dB 250kbps
- Coverage in closed spaces: 15m / 30m
- SPI interface
- Input voltage: 1.9V- 3.6V
- Input / output port voltage: 0V-3.3V / 5V
- Coverage in open areas: 100m approx.
- Clock frequency: 16MHz

Ideal for projects with ARDUINO you can use it with PIC, AVR, STM32.
Provides seconds, minutes, time and date, calendar up to the year 2100.
DS1302 Real Time Clock RTC Module AVR ARM PIC features:
- Chip: DS1302
- Power supply: 2V-5V
- Operating current: <2mA
- Dimensions: 44 x23 x 8mm
- Battery not included in this sale
- Connect the RTC to your Arduino
VCC -> Arduino + 3.3V
GND -> Arduino Gnd
CLK -> (SCLK_PIN)
DAT -> (IO_PIN)
RST -> (CE_PIN)