RFID PN532 NFC Module

Characteristic:
-10k OHM kΩ - linear potentiometer 10k Arduino
-Tolerance: +/- 20%
- Power: 0.125W

ProtoShield Prototype Expansion Board with Mini Breadboard 170 points for Arduino UNO V5.0 features:
- To mount your projects in a comfortable and orderly way, access to all the pins of Arduino Uno R3, it has a universal plate and protoboard zone, 5V and Gnd buses, reset pushbutton, pushbutton and 2 general purpose leds, zones for integrated Soic and Dip
- The seamless mini breadboard has 170 connection points.
- You can stick on the shield with its self-adhesive back.

Led infrared sensor.
Detector of the source of fire or flame, can detect a flame or wavelength 760 nm-1100 nm
Particularly sensitive to the flame spectrum.
This optical flame sensor is a device that detects the existence of combustion by the light emitted by it.
Infrared LED Flame Sensor 5mm features:
- Range of light, Distance of 80 cm.
- Angle detection of about 60 degrees,
- This light can be detected by an optical sensor,
- Can be captured by digital inputs and analog inputs of Arduino.

Resistor 10K Ohm 5% 0,25W 1/4W features:
-10K Ohm
-Type: Carbon film
-Tolerance: ±5%
-Power: 0.25W
-Dimensions: 2x7mm

- It has an Atmega328P chip running at 16Mhz with a factory loaded bootloader - The Uno R3 module has all the connectors than the Arduino Uno R3 and is compatible with all Arduino shields Arduino compatible UNO R3 board features:
- Includes USB Cable - ATmega328P 16MHz chip with external quartz crystal
- Microprocessor: ATmega328
- Operating voltage: 5V
- Input voltage (recommended): 7-12V
- Input voltage (limits): 6-20V
- Clock speed: 16 MHz
- Digital I / O Pins: 14
- Analog input pins: 6
- DC current per I / O Pin: 40 mA
- DC Current per Pin 3.3V: 50 mA
- Flash32 KB of which 0.5 KB are used by the bootloader - Atmega328
- SRAM 2 KB - Atmega328

The piezoelectric buzzer has a simple structure in which a ceramic piezoelectric disk is affixed to a vibrating plate. An alternative voltage applied to this element will cause a contraction or diametrical expansion of the element. This feature is used to fold a vibrating plate, which generates sounds. 2x Passive Buzzer 5V features:

- Input voltage: 3V to 12V
- Diameter: 12mm
- Height: 7.5mm
- Pin spacing: 6.5mm
- Impedance: 16 Ohm
- Working frequency: 2 to 5 KHz
- Quantity: 1 unit

LED Diode Assortment Kit 30 pcs 5mm red, green, yellow features:
- Lens color: red, green, yellow - diffuse
- Size: 5mm
- Operating current: 20mA
- Voltage (red) 1,8V-2,3V
- Voltage (green) 3,2V-3,4V
- Voltage (yellow) 1,8V-2,3V
- Anode (A): Positive (long leg): 28mm
- Catode (K): Negative (short leg): 25mm
- Operating temperature: -25ºC/80ºC
- Welding temperature: +260ºC
- Quantity: 30 units
*10x red
*10x green
*10x yellow

The DHT11 humidity sensor is presented in a plastic body ideal for mounting on a panel or similar. It uses a capacitive sensor that returns a digital signal with the measurement.
Characteristic:
- Operating voltage: 3 to 5 VDC - Humidity measurement range: 20-95% ± 5% accuracy
- Temperature measurement range: 0ºC to 50ºC ± 2º accuracy
- Maximum sampling rate: 2 seconds - Working current 2.5mA
- 1-wire interface
- Dimensions: 32 x14 mm
- Quantity: 1 unit with 3x female / female cables