Expansion Module I/O XBEE

GSM A6 Four Band GPRS Module with MCU Antenna features:
- GSM / GPRS module / development board / shield based on GPRS A6
- Supports GSM / Dual band GPRS, available for remote GPRS and SMS data transmission
- Compact size and low current consumption
- With energy saving technique, current consumption is as low as 5mA (sleep mode)
- Communicates with the microcontroller through the UART port, supports the command including GSM 07.07, GSM 07.05 and Ai-Thinker Enhanced AT Commands
- Working frequency: four-band network, 850 / 900/1800 / 1900MHz
- Operating voltage: 4.8-9VDC (Supply power of the on-board regulator circuit for the A6 module)
- Working current: 2A maximum
- Current Sleep: 5mA

This mini vibration motor runs on 5 VDC and can be used for Arduino and Raspberry projects. It is a direct current motor.
Mini vibration engine for Arduino and Raspberry Pi 5 VDC features:
- Voltage: 5 VDC,
- Current: 75mA,
- Rotation speed: 1100 (rpm),
- Efficiency: 80%,
- Dimensions: 10x27mm.

W1209 DC 12V Thermostat + Transparent Box Temperature Controller features:
- Model: W1209
- Supply voltage: DC 12V
- Temperature control mode: ON / OFF
- Temperature range: -50-110 ° C
- Resolution: 0.1 ° C range -9.9 ~ 99.9 ° C, above is 1 ° C
- Measure accuracy: 0.1 ° C
- Refresh rate: 0.5s
- Temperature protection 0-110 ° C
- Static current: ‰ ¤ 35mA, working current ‰ ¤ 65mA
- Output power: 10A relay
- Probe sensor: NTC (10K 0.5%) Waterproof Sensor
- Environmental requirements: -10 ~ 60 ° c Humidity 20% -85%
- Dimensions: 48 x 40mm

The network module communicates with the Arduino type board through the SPI protocol ideal for projects with ARDUINO, PIC, AVR, STM32. ENC28J60 Ethernet LAN Network Module Mini AVR LPC STM3 features:
- Chip ENC28J60 Microchip
- Module: 10Base-T
- 3.3V power
- SPI interface
- 25Mhz speed
- LED status LED
- Hanrun network transformer
- Network Interface board HR911105A
- Operating temperature: -40ºC to + 85ºC
- Dimensions: 51 x 19 x 16 mm

The Bluetooth HC-06 module is one of the best options for projects where you need wireless communications. Arduino Wireless Module HC-06 HC06 features:
- CSR BC417 Chipset
- Power: 3.3V
- Bluetooth version V2.0 + EDR
- Frequency: 2.4GHz band ISM
- Modulation: GFSK
- Range approx. 10m
- Security: Authentication and encryption.
- Speed- & gt; Asynchronous: 2.1Mbps (Max) / 160 kbps; Synchronous: 1Mbps / 1Mbps
- Supports AT commands for configuration through a serial port
- Working temperature: -20 ºC to +75 ºC - Working current - pairing: 80 mA
- Transmission: 8mA
- Size: 28 x 12mm

This module is used to extend the Raspberry's 40 GPIO pins to another set of 2x20 male pins and 8 parallel pins accessible on the terminal blocks in the that test leads are pushed. The electronic board offers great reliability with the Raspberry and is very easy to connect thanks to its existing suitable accessories but not included.
The module offers a set of mini jumpers to configure the GPIO.
The press to release the two terminal blocks of 20 connections is very easy to use. Raspberry Pi 2-3 Model B Multifunction Expansion GPIO Module features:
- Communication connections: 1 TXD0 (emission) and 1 RXD0 (reception)
- Power connections: 5 of 3.3V, 2 of 5V and 5 of GND
- Connections for pulse width modulation ( PWM): 2
- GPIO connections: 11

This external wireless antenna module CC1101 is suitable for Funduino and Arduino projects.
The CC1101 module of 1.2K baud consists of a domestic R & Lotes unit to improve the effective communication distance.
This is a significant improvement over the CC1100 module.
It allows to adjust the speed of the bits for different uses, thus allowing a higher transmission speed.
Supports 2-FSK, GFSK and msk modulations. It also has a high sensitivity (1.2kbps @>

NFC module for Educational STEAM Kit.  Near field communication (NFC) is a set of standards for smartphones and similar devices to establish radio communication with each other by touching them together or bringing them into close proximity, usually no more than a few centimeters. Compatible with almost any microcontroller, Arduino, PIC, AVR. It can be used in Access Control projects and Alarm projects. RFID PN532 NFC Module features:
- Based on the NXP PN532 chip, it can be used for non-contact communication of 13.56M.
- Greater effective communication distance of 3 cm.

Sonoff RE5V1C Wi-Fi relay switch (IM171018005) has nano size and dry contact output.

Sonoff products will transform your ordinary home into a smart home that is controlled via an internet-connected phone.

Allows control: - Up to 2 bidirectional current motors
- Or 1 stepper motor Shield is compatible with NodeMcu ESP8266 CP2102 WIFI Development Board ESP8266 WiFi Motor Drive L293D Expansion Shield Board ESP12E NodeMcu features:
- Minimum operating voltage: 4.5 V
- Maximum operating voltage: 36 V
- Maximum current: ± 1.2 A
- Logic voltage: - 2.3V <= HIV <= VIN (high)
                        - 0.3V <= VIL <= 1.5V (low)
- Controller L293D
- Measures: 58x42 mm ESP12 port control kit: - D1, D3 - motorA
- D2, D4 - motorB