Power Supplies

Rechargeable battery XTAR 18650 2200mAh Li-ion features:
- With PCB protection circuit that protects the battery against overcharges and over discharges, increasing battery life
- Quantity: 1 unit
- Authentic Protection Battery

Battery Compartment 9V 6LF22 Power cable features:
- Cable 17cm long
- DC connector 5.5 / 2.5mm
- Dimensions 54x 30x 20mm
- Batteries 6LR61, 6LF22, X22 or compatible
- It has 3 holes for anchoring to plate or chassis

Battery Holder Button 3V CR2032 PCB CR2032 PCB features:
- Battery compartment for PCB printed circuit
- Quantity: 1 unit

Lithium Battery 3V CR2032 Button with PCB Pins features:
- 3V battery for horizontal mounting PCB printed circuit
- Quantity: 1 unit
- Diameter: 20mm
- Voltage: 3V
- Capacity: 220mAh

Instruction: - The drawing of the polarities is not correct, it is wrong
- Put the batteries in parallel Characteristic: - Cable 15cm long
- Measures 74x42x 20mm
- Weight: 10 gr. (Approx.)
- Stack length max 67mm

Battery 9V/E Block Varta Industrial 4022 6F22 6LR61 580mAh features:
- 9V Varta Industrial 6F22 Battery
- High quality, made in Germany
- Quantity: 1 unit

Ideal to power your Arduino board through the power input.
Adapter Battery 9V 6F22 Jack Connector DC features:
- Cable 7cm long
- Battery connector 9V, 6F22
- Male connector DC 5.5 / 2.5

Characteristic:
- For long periods of storage it must be stored below 45 ° C
- After periods of Long storage will probably need to do a few charge cycles to increase capacity again
- Quantity: 1 unit
Precautions:
No Change polarity.
Do not heat the battery, or expose it to high temperatures.
Do not wet or expose to high humidity environments.

Includes a switch to output the voltage built into the case itself.
It has a cover for protect the batteries.
The cover has perforation in case you want to secure it with a screw (not included).
Characteristic:
- Cable 12cm long
- Measures 70x 65x 18mm
- Battery length max 50mm
- Compatible batteries (LR06, R06, MN1500, AM3, UM3, HP7)

Characteristic: - Lithium Battery WITHOUT Protection
- Nominal capacity: 2600mAh (discharge of 0.2C, 2.75V)
- Minimum capacity: 2550mAh (0.2C, 2.75V discharge)
- Charging voltage: 4.2 ± 0.05 V
- Nominal voltage: 3.63V
- Charging method: DC-CV (constant voltage with current limited)
- Charging current: standard charge: 1300mA, fast charge: 2600mA
- Charging time: standard charge: 3 hours, fast charge: 2.5 hours
- Max. Charging current: 2600mA (ambient temperature 25 °)
- Max. Discharge current: 5200mA (ambient temperature 25 °)
- Discharge cut-off voltage: 2.75V
- Cell weight: 47.0g maximum
- Cell dimension: Height: 65.00 mm max., Diameter: 18.40 mm max.

Includes a switch to output the voltage built into the case itself.
It has a cover to protect the batteries.
The cover has perforation in case you want to secure it with a screw (not included).
Battery holder 2x AA Battery holder with switch features:

- Cable 15cm long
- Measurements 68x 32x 18mm
- Battery length max 50mm
- Compatible batteries (LR06, R06, MN1500, AM3, UM3 , HP7)

Rechargeable Battery XTAR 18650 2600mAh Li-ion features:
- With PCB protection circuit that protects the battery against overcharges and over-discharges, increasing battery life
- Quantity: 1 unit

Ideal to power your Arduino board through the power input.
5x 9v Battery Adapter Connector 6F22 with Cable features:

- Cable 15cm long
- Battery connector 9V, 6F22

Panasonic rechargeable battery NCR18650B 3400mAh Li-ion 3,6V features:
- Nominal capacity: 3350mAh (0.2C, 2.5V discharge)
- Minimum capacity: 3250mAh (0.2C, 2.5V discharge)
- Charging voltage: 4.2 ± 0.05 V
- Nominal voltage: 3.6V
- Charging method: CC-CV (constant voltage with limited current )
- Charging current: standard charge: 1625mA,
- Charging time: standard charge: 4 hours,
- Max. Discharge current: 6500 mA (ambient temperature 25 °)
- Discharge cut-off voltage: 2.5V
- Cell weight: 47.5g maximum
- Cell dimension: Height: 65.30 mm maximum, Diameter: 18.50 mm maximum
- Operating temperature: charge: 0 to 45 ° C, discharge: -20 to 60 ° C

Characteristic: - Button cell battery
- For 20mm diameter battery type CR2032
- ON / OFF switch
- Dimension: 50mm (L) x 23mm (W) x 6mm (D)

4x AA 6V battery holder with DC connector features:
- Cable 12cm long
- Measurements 62x56x 16mm
- Battery length max 50mm
- Compatible batteries ( LR06, R06, MN1500, AM3, UM3, HP7)

Battery holder 4x AA 6V LR06 features:
- Cable 13cm long
- Measurements 62x56x 16mm
- Battery length max 50mm
- Compatible batteries ( LR06, R06, MN1500, AM3, UM3, HP7)

Characteristic: - Cable 13cm long
- Measurements 49x 52x 13mm
- Battery length max 44mm
- Compatible batteries (LR03, 24A, R03, RX03, MN2400, AM4, UM4)

Rechargeable Battery Samsung INR18650 2500mAh Li-ion 3.7V 20A unprotected features:
IMPORTANT: This battery does not have a protection circuit.
Use it at your own risk.
Do not charge over 4.2V
Do not discharge below 3V
Do not change polarity
Do not heat the battery, or expose it to high temperatures
Do not wet or expose to environments of High humidity
For long periods of storage it should be stored below 45 ° C
After long periods of storage you will probably need to do some charging cycles to increase the capacity again.
Quantity: 1 unit
Nominal capacity: 2500mAh (0.2C, 2.75V discharge)
Minimum capacity: 2450mAh (0.2C, 2.75V discharge)
Charging voltage: 4.2 ± 0.05 V

Ideal to power your Arduino board.
Battery Holder 6x AA LR06 features:
- Cable 12cm long,
- Measures 90x 55x 15mm,
- Max 50mm pile length,
- Compatible batteries (LR06, R06, MN1500, AM3, UM3, HP7).

Battery Varta Industrial AA - 4006 LR06 Mignon 1,5V- pack 4unds features:
- 1.5V Varta Industrial LR06 Battery
- High quality, made in Germany
- Quantity: 4 units

Ideal to power your Arduino board.
Battery Holder 6x AA with DC Connector 9V LR06 features:
- Cable 12cm long,
- Measures 90x 55x 15mm,
- Max 50mm pile length,
- Compatible batteries (LR06, R06, MN1500, AM3, UM3, HP7).

Characteristic: - Lithium Battery WITHOUT Protection
- Nominal capacity: 3450mAh (0.2C, discharge of 2.5V)
- Minimum capacity: 3350mAh (0.2C, 2.5V discharge)
- Charging voltage: 4.2 ± 0.05 V
- Nominal voltage: 3.6V
- Charging method: DC-CV (constant voltage with current limited)
- Charging current: standard charge: 1675mA,
- Max. Discharge current: 10A (ambient temperature 25 °)
- Charging time: standard charge: 4 hours,
- Discharge cut-off voltage: 2.5V
- Cell weight: 47g maximum
- Cell dimension: Height: 65.30 mm maximum, Diameter: 18.50 mm maximum

Characteristic: - Cable 15cm long
- Measurements 74x21x 19mm
- Weight: 8 gr. (approx.)
- Stack length max 67mm

3V CR1220 button lithium battery features:
- 3V battery
- Diameter: 12.5mm
- Voltage: 3V
- Capacity: 45mAh
- Quantity: 1 unit

4x 18650 3.7V Parallel Lithium Battery features:
- Cable 10cm long
- Measures 80x76x 20mm
- Stack length max 67mm

4x everActive R6 / AA 2000 mAh Ni-MH 1.2V rechargeable batteries features:
- Batteries in Blister
- Nominal capacity: 2000mAh
- Minimum capacity: 1900mAh - Nominal voltage: 1.2V
- Cell dimension: Height: 50.50 mm max
- Diameter: 14.50 mm max

Battery Holder R6 LR06 4+4 8x AA 12V features:
- Cable 14cm long
- Measures 58x 32x 30mm
- Compatible batteries (LR06, R06, MN1500, AM3, UM3, HP7)

The battery with PCB protection circuit that protects the battery against overcharges and over-discharges, increasing battery life Rechargeable battery XTAR 18650 3500mAh Li-ion features:
- the cell used: Panasonic-Sanyo
- capacity: 3500mAh
- nominal voltage 3.6V
- recommended maximum charge current 1.6A
- recommended maximum discharge current 10A - maximum charging voltage 4.25V
- dimensions:
diameter: 18.40mm ± 0.3mm | height: 68.80mm ± 0.5mm - weight 48.5g - quantity: 1 unit

LITHIUM POLYMER BATTERY Battery LIPO 180mAh 3.7V features:
-Battery type-lithium polymer. -Type of battery terminals- 3 wires. -Voltage of the battery-3.7 V -Capacity of the battery- 180 mAh. - Embedded PCM security chip (protection against overload, over discharge, short circuit Dimensions: -Length / depth of the battery- 20 mm -Battery width / diameter -31 mm It has three cables with a 3-pin connector with a separation of 2 mm. Wires: Red: positive. Black: negative. Yellow: thermistor output. The technical file: Battery LIPO.pdf

LITHIUM POLYMER BATTERY Battery LIPO 190mAh 3.7V features:
-Battery type-lithium polymer. - Type of battery terminals- 3 cables. -Voltage of the battery-3.7 V -Capacity of the battery- 190 mAh. - Embedded PCM security chip (protection against overload, over discharge, short circuit). Dimensions: -Battery length / depth- 33 mm -Battery width / diameter- 44 mm It has three cables with a 3-pin connector with a separation of 2 mm. Cables: Red: positive. Black: negative. Yellow: thermistor output.

Battery holder 2x AA 3V features:
- Cable 15cm long
- Measurements 59x 33x 16mm
- Compatible batteries (LR06, R06, MN1500, AM3, UM3 , HP7)

LITHIUM POLYMER BATTERY Battery LIPO 210mAh 3.7V features:
-Battery type-lithium polymer. - Type of battery terminals- 3 wires. -Voltage of the battery-3.7 V -Capacity of the battery- 210 mAh. - Embedded PCM security chip (protection against overcharging, over discharge, short circuit) Dimensions: -Length / depth of battery- 25mm -Battery width / diameter- 31 mm It has three cables with a 3-pin connector with a separation of 2 mm. Cables: Red: positive. Black: negative. Yellow: thermistor output.

Lithium Battery Holder Button 3V CR1220 THT PCB features:
- Material:
    - Contact: Phosphor Bronze
- Electric:
    - Type: THT
    - Contact Resistance: 30 Milliohms Max
    - Insulation Resistance: 1000 Mega Ohms Min
    - Dielectric Voltage: 500V AC one sec level
    - Operating Temperature: -25 „ƒ - 85 „ƒ
- Suitable for Computer Memory, Power transfer, Communications Power System, PC Application, Armamentarium, Motherboard

LITHIUM POLYMER BATTERY Battery LIPO 2650mAh 3.7V features:
-Battery type-lithium polymer. - Type of battery terminals- 3 wires. -Voltage of the battery-3.7 V -Capacity of the battery- 2650 mAh. - Embedded PCM security chip (protection against overload, over discharge, short circuit). Dimensions: -Length / depth of the battery- 71 mm -Width / diameter of the battery- 95 mm It has three cables with a 3-pin connector with a separation of 2 mm. Cables: Red: positive. Black: negative. Yellow: thermistor output.

Lithium Battery Holder Button 3V CR1220 SMD PCB features:
- Diameter: 15 mm
- Thickness: 4 mm
- Type: SMD
- Use it for CR1220 battery
- Suitable for Computer Memory, Power transfer, Communications Power System, PC Application, Armamentarium, Motherboard

Weight: 12.7g
Box size: 62 * 25 * 10 mm

LITHIUM POLYMER BATTERY Battery LIPO 2800mAh 3.7V features:
-Battery type-lithium polymer. - Type of battery terminals- 3 wires. -Voltage of the battery-3.7 V -Capacity of the battery- 2800 mAh. - Embedded PCM security chip (protection against overload, over discharge, short circuit). Dimensions: -Length / depth of the battery- 78 mm -Width / diameter of the battery- 100 mm It has three cables with a 3-pin connector with a separation of 2 mm. Cables: Red: positive. Black: negative. Yellow: thermistor output.

Specifications: Voltage: 6V
Capacity: 4.5Ah
Dimension
- length: 70mm
- width: 48mm
- height: 100mm
- total height (with terminals): 106mm
Weight: 0.71 kg Gel Battery 6V 4.5Ah features:

"Standby" mode (25 ºC): 6.8-6.9V
Cyclical work (25 ºC): 7.25-7.45V
Maximum starting current:

Base of two 18650 batteries to solder on PCB. Characteristic: - Measurements 78x 40x 21mm
- Weight: 10 gr . (approx.)
- Stack length max 67mm

Specifications: Voltage: 6V
Capacity: 3.3Ah
Dimension
- length: 134mm
- width: 34mm
- height: 60mm
- total height (with terminals): 67mm
Weight: 0.69 kg Gel Battery 6V 3.3Ah features:

"Standby" mode (25 ºC): 6.8-6.9V
Cyclical work (25 ºC): 7.25-7.45V
Maximum starting current: - 0 ºC: 85%
- -15 ºC: 62%
Self discharge (25 ºC)
- capacity after 3 months of storage: 91%
- capacity after 6 months storage: 82%
- capacity after 12 months storage: 64%

18650 battery base for soldering to PCB. Characteristic: - Measurements 78x 20x 21mm
- Weight: 10 gr. ( approx.)
- Stack length max 67mm

Specifications: Voltage: 6V Capacity: 1.3Ah Dimension
- length: 96mm - width: 24mm
- height: 51mm
- total height (with terminals): 58mm
Weight: 0.31 kg Gel Battery 6V 1.3Ah features:

"Standby" mode (25 ºC): 6.8-6.9V
Cyclical work (25 ºC): 7.25-7.45V
Maximum starting current: Capacity (25 ºC)
- 20 hour rate: 1.30Ah
- 10 hour rate: 1.24Ah
- 5 hour rate: 1.09Ah
- Rate 1 hour: 0.78Ah
Internal resistance (full charged battery, degree 25 ºC): 36 mOhm
Capacity affected by temperature
- 40 ºC: 102%
- 25 ºC: 100%
- 0 ºC: 85%
- -15 ºC: 62%
Self-discharge (25 ºC)

Battery holder for 18650 batteries connected in series.

Lead-acid battery made of AGM (Absorbent Glass Mat). Lead plates and high-quality electrolyte ensure the reliability of the power supply voltages that support most systems, such as UPS and emergency power systems.
Application: Alarm systems Cable television systems Telecommunications equipment Monitoring equipment Protection systems Medical equipment Ups Emergency Power Supply Toys
General Gel Battery 12V 2.3Ah Xtreme features:
Maintenance-free Design prevents leaks Watertight case Explosion safety valve protection High quality and reliability Extremely strong capacity recovery property Low self-discharge characteristics Can be installed in multiple positions

The batteries are manufactured on a modern production line. They have a gel-shaped electrolyte, so they are maintenance-free batteries. The batteries are designed to function as both shock absorbers and cyclic. They are characterized by their durability and a very favorable price-performance ratio. Gel Battery 12V 2.3Ah features:
> Long service life - both on the job and on the cyclic damper. No delamination effect of gelled electrolyte. Tolerates high operating temperatures. Fully returns to initial deep discharge volume. Very high performance. Capacity (Ah): 2,3 Nominal voltage (V): 12 LxAnxAl dimensions (mm): 177x33x60 Gross weight: 0.96

The batteries are manufactured on a modern production line. They have a gel-shaped electrolyte, so they are maintenance-free batteries. They are characterized by their durability and a very favorable value for money. Gel Battery 12V 0.8Ah features:
Long service life-both on the job and on the cyclic damper. No delamination effect of gelled electrolyte. Tolerates high operating temperatures. Fully returns to initial deep discharge volume. Very high performance. Capacity (Ah): 0.8 Tensi Nominal ion (V): 12 LxAnxAl dimensions (mm): 96x28x61 Gross weight (kg): 0.32

Rechargeable battery 9V 6F22 Ni-MH 250 mAh Ready to Use features:

The battery with PCB protection circuit that protects the battery against overcharges and over-discharges, increasing battery life Rechargeable battery XTAR 18650 3000mAh Li-ion features:
- the cell used: Panasonic-Sanyo
- capacity: 3000mAh
- nominal voltage 3.6V
- recommended maximum charge current 1.5A
- recommended maximum discharge current 4.5A
- maximum charge voltage 4.25V
- dimensions:
diameter: 18.40mm ± 0.3mm | height: 68.80mm ± 0.5mm - weight 48.5g - quantity: 1 unit

Lithium polymer battery 3.7 V with the capacity of 590 mAh. Includes PCM safety chip (protection against overcharge, over-discharge, short circuit).

Battery terminal type-3 wires.

Battery voltage-3.7 V

Battery capacity- 590 mAh.

Gel Battery 12V 7Ah features:

• Long service life - both in cyclic and buffer operation
• No delamination effect from the gelled electrolyte
• It tolerates high operating temperatures well
• It fully recovers to its original capacity from deep discharge

Gel Battery 6V 4Ah features:

• Long service life - both in cyclic and buffer operation
• No delamination effect from the gelled electrolyte
• It tolerates high operating temperatures well
• It fully recovers to its original capacity from deep discharge

Gel Battery 12V 1.2Ah features:

• Long service life - both in cyclic and buffer operation
• No delamination effect from the gelled electrolyte
• It tolerates high operating temperatures well
• It fully recovers to its original capacity from deep discharge

Nickel strip in the shape of a square plate to join 4 poles of 4 welded batteries with connection projection. Tape sheets, lithium battery welding.

Nickel tape to join the battery poles welded with connection projection. A roll of 1kg / 260m.

Nickel tape to join the battery poles welded with connection projection. A roll of 1kg / 105m.

20 meter wide shrink film for one 18650 stack to wrap

20 meter wide shrink film for two 18650 stack to wrap

Single sheet of two 18650 stack width shrink film for wrapping.