Battery LIPO 190mAh 3.7V

This small 10-DOF sensor module GY-91 is more compact than the GY-80 module.
The module uses a unique MPU-9250 chip combination with built-in 3-axis gyroscope, 3-axis accelerometer, digital compass and BMP280 enhanced barometric pressure sensor.
The MPU-9250, delivered in a 3x3x1mm QFN package, is the smallest 9-axis MotionTracking device in the world and incorporates the latest InvenSense design innovations, allowing dramatically reduced chip size and power consumption, while improving the performance and the cost. Enhancements include low-power accelerometer mode support with only 6.4μA of and provides improved 16-bit compass data resolution (0.15 μT per LSB).

Pressure sensor sometimes called strain gauge. Load cell for measuring weights up to 50kg. The transducer measures the strain of the metal structure and converts it into a few mV.

LITHIUM POLYMER BATTERY Battery LIPO 190mAh 3.7V features:
-Battery type-lithium polymer. - Type of battery terminals- 3 cables. -Voltage of the battery-3.7 V -Capacity of the battery- 190 mAh. - Embedded PCM security chip (protection against overload, over discharge, short circuit). Dimensions: -Battery length / depth- 33 mm -Battery width / diameter- 44 mm It has three cables with a 3-pin connector with a separation of 2 mm. Cables: Red: positive. Black: negative. Yellow: thermistor output.

32GB Class 10 MicroSD memory card with adapter features:
- Capacity 32GB
- Class 10
- Dimensions of the microSD 11 mm x 15 mm x 1 mm
- FAT32 format
- Operating temperature -25 ° C to 85 ° C
- Storage temperature -40 ° C to 85 ° C
- Voltage 3.3 - Includes adapter

This module adapted for the arduino includes a laser diode and a 3-pin connector for a simple and quick adaptation with the Arduino. The diode is mainly used for laser toys, all kinds of level meter, instruments, stylus pen, mini LCD projector, remote listeners laser, alarm anti-theft light remote control. Light shots and different display can make the color of the image element a little different from the real object. The measurement allowed error is +/- 1-3 cm. Characteristic: - Supply voltage: 5VDC
- Connector of 3 pins:
1- GND
2- VCC
3- Light control of the laser diode
- Point mode: point facula
- Continuous output
- Operating temperature: -36 ° C - + 65 ° C
- Laser wavelength: 650nm (red)

Load cell Load Cell 20kg features:
- Load range: 20kg
- Operating voltage: 3VDC ~ 14 VDC
- Nominal output: 1.0 ± 0.15mV / V
- Repeatability: 0.03% FS
- Effect of the temperature at the outlet: 0.01% F.S /°C
- Effect of temperature on zero: 0.05% F.S /°C
- Zero: ± 0.1000 mV / V
- Input impedance: 1115 + -10% Ω
- Output impedance: 1000 + - 10% Ω
- Insulation resistance:> = 1000 MΩ
- Safe Overload Rate: 150% FS
- Final overload rate: 200% FS
- Temperature range: -20 - 60 °C
- Material: Aluminum alloy
- Degree of protection: IP65
- Cable length: 25 cm
- Size: 75 x 12.7 x 12.7 mm
- Wiring:
* Red: Feeding +
* Black: Source -
* Green: Sign +
* White: Signal -

Pack 10pcs of micro servo 9g SG90.

You can easily control any device over the Internet through your phone, computer, etc.
The module can handle 5 users at the same time, it can work in two modes: STA (client) and AP (access point).
In AP mode, the module is connected via WIFI directly to your phone or computer (in open field can be up to 300 meters).
In STA mode, the relay module is connected to the access point (router) that supplies the network.
Wi-Fi in the room where the relays are located. In this case, the range mainly depends on the power of the access point antennas (routers).
You should not turn off after the configuration is completed, as some of the parameters of the WIFI module cannot be saved when power is cut off.