Arduino compatible Nano V3.0 CH340 board Version compatible with Arduino Nano V3.0 It has an ATMega328P chip running at 16Mhz with bootloader loaded factory. Characteristic: - Microcontroller: ATmega328 - Operating Voltage (logic level): 5V - Input Voltage (recommended): 7-12V - Digital I / O Pins: 14 (6 PWM outputs) - Analog Inputs: 8 (A0-A7) - DC Current per I / O pin 40 mA - Flash memory: 32 KB (2 KB used by the bootloader) - SRAM: 2 KB - EEPROM: 1 KB - Frequency Clock: 16 MHz - USB Communication - CH340 - Dimensions: 18 mm x 44 mm Code B0006 Available Price €8.95
Female Strip 40 Short Pins Female Strip 40 Short Pins features: - Pin spacing: 2.54mm - Insert position: Vertical - Insert: Pasante - Quantity: 1 unit of strips of 40 female pins each Code K0139 Available Price €0.69
Integrated Circuit Supports DIP18 Width 10.16mm Integrated Circuit Supports DIP18 Width 10.16mm features: - Type: DIP DIL- Total number of pins: 18- Step between pins: 2.54 mm- Material: Polybutylene terephthalate- Length: 20.32 mm- Width: 10.16 mm- Temperature min .: -25 °C- Max temperature: +85 °C- RoHS compliant Code Z0007 Backorder Price €0.19
Load Cell Weight Sensor 1kg Load Cell 1 kg Scale Sensor Weight Arduino Load cell to measure weight up to 1kgThe transducer measures the deformation of the metal structure and converts it into a few mV. Load cell Load Cell Weight Sensor 1kg features: - Load range: 1kg- Operating voltage: 3VDC ~ 14 VDC.- Nominal output: 1.0 ± 0.15mV / V- Repeatability: 0.03% FS- Effect of the temperature at the outlet: 0.01% F.S / ° C Code M0124 Available Regular price €2.99 -€0.99 Price €2.00
5x Strip 16 Pin Female Short 5x Strip 16 Pin Female Short features: - Pin spacing: 2.54mm - Insert position: Vertical - Insert: Through - Quantity: 5 units of strips of 16 female pins each Code K0141 Available Price €0.26
DHT11 Module Temperature and Humidity Sensor The DHT11 humidity sensor is presented in a plastic body ideal for mounting on a panel or similar. It uses a capacitive sensor that returns a digital signal with the measurement. Characteristic: - Operating voltage: 3 to 5 VDC - Humidity measurement range: 20-95% ± 5% accuracy - Temperature measurement range: 0ºC to 50ºC ± 2º accuracy - Maximum sampling rate: 2 seconds - Working current 2.5mA - 1-wire interface - Dimensions: 32 x14 mm - Quantity: 1 unit with 3x female / female cables Code S0001 Available Price €2.99
5x 9v Battery Adapter Connector 6F22 with Cable Ideal to power your Arduino board through the power input. 5x 9v Battery Adapter Connector 6F22 with Cable features: - Cable 15cm long - Battery connector 9V, 6F22 Code PP013 Available Price €0.55
Relay SRD-12 DC-2P 12V 10A SPDT Relay SRD-12 DC-2P 12V 10A SPDT features:- Supply voltage: 12V- Output Current: 10A- Relay activation current: 15mA ~ 20mA- For power switching with 12V DC signals - Microcontroller, Arduino, Electronica Code RL012 Available Price €0.98
Adapter Battery 9V 6F22 Jack Connector DC Ideal to power your Arduino board through the power input.Adapter Battery 9V 6F22 Jack Connector DC features:- Cable 7cm long- Battery connector 9V, 6F22- Male connector DC 5.5 / 2.5 Code PP011 Available Price €0.75
Battery holder 4x AA 6V LR06 Battery holder 4x AA 6V LR06 features: - Cable 13cm long - Measurements 62x56x 16mm - Battery length max 50mm - Compatible batteries ( LR06, R06, MN1500, AM3, UM3, HP7) Code PP003 Available Price €1.49
Battery holder 2x CR2032 Switch Characteristic: - Button cell battery - For 20mm diameter battery type CR2032 - ON / OFF switch - Dimension: 50mm (L) x 23mm (W) x 6mm (D) Code PP23 Backorder Price €1.19
4x AA battery holder 4-battery holder with 6V switch Includes a switch to output the voltage built into the case itself. It has a cover for protect the batteries. The cover has perforation in case you want to secure it with a screw (not included). Characteristic: - Cable 12cm long - Measures 70x 65x 18mm - Battery length max 50mm - Compatible batteries (LR06, R06, MN1500, AM3, UM3, HP7) Code PP006 Available Price €1.85
Battery Holder Button 3V CR2032 PCB CR2032 PCB Battery Holder Button 3V CR2032 PCB CR2032 PCB features: - Battery compartment for PCB printed circuit- Quantity: 1 unit Code PP022 Available Regular price €1.29 -€0.30 Price €0.99
5x 9v Battery Adapter Connector 6F22 with Cable Ideal to power your Arduino board through the power input. 5x 9v Battery Adapter Connector 6F22 with Cable features: - Cable 15cm long - Battery connector 9V, 6F22 Code PP013 Available Price €0.55
Battery holder 2x 18650 PCB mount Base of two 18650 batteries to solder on PCB. Characteristic: - Measurements 78x 40x 21mm - Weight: 10 gr . (approx.) - Stack length max 67mm Code PP052 Available Regular price €2.49 -€0.40 Price €2.09
Battery holder 1x 18650 PCB mount 18650 battery base for soldering to PCB. Characteristic: - Measurements 78x 20x 21mm - Weight: 10 gr. ( approx.) - Stack length max 67mm Code PP053 Available Regular price €1.99 -€0.30 Price €1.69
Battery holder 4x AAA 6V Characteristic: - Cable 13cm long - Measurements 49x 52x 13mm - Battery length max 44mm - Compatible batteries (LR03, 24A, R03, RX03, MN2400, AM4, UM4) Code PP001 Available Price €1.19
Battery holder 2x 18650 3,7V Parallel Lithium Battery Instruction: - The drawing of the polarities is not correct, it is wrong - Put the batteries in parallel Characteristic: - Cable 15cm long - Measures 74x42x 20mm - Weight: 10 gr. (Approx.) - Stack length max 67mm Code PP016 Available Price €1.85
Adapter Battery 9V 6F22 Jack Connector DC Ideal to power your Arduino board through the power input.Adapter Battery 9V 6F22 Jack Connector DC features:- Cable 7cm long- Battery connector 9V, 6F22- Male connector DC 5.5 / 2.5 Code PP011 Available Price €0.75
Battery holder 4x AA 6V LR06 Battery holder 4x AA 6V LR06 features: - Cable 13cm long - Measurements 62x56x 16mm - Battery length max 50mm - Compatible batteries ( LR06, R06, MN1500, AM3, UM3, HP7) Code PP003 Available Price €1.49
Battery holder 2x CR2032 Switch Characteristic: - Button cell battery - For 20mm diameter battery type CR2032 - ON / OFF switch - Dimension: 50mm (L) x 23mm (W) x 6mm (D) Code PP23 Backorder Price €1.19
4x AA battery holder 4-battery holder with 6V switch Includes a switch to output the voltage built into the case itself. It has a cover for protect the batteries. The cover has perforation in case you want to secure it with a screw (not included). Characteristic: - Cable 12cm long - Measures 70x 65x 18mm - Battery length max 50mm - Compatible batteries (LR06, R06, MN1500, AM3, UM3, HP7) Code PP006 Available Price €1.85
Battery Holder Button 3V CR2032 PCB CR2032 PCB Battery Holder Button 3V CR2032 PCB CR2032 PCB features: - Battery compartment for PCB printed circuit- Quantity: 1 unit Code PP022 Available Regular price €1.29 -€0.30 Price €0.99
5x 9v Battery Adapter Connector 6F22 with Cable Ideal to power your Arduino board through the power input. 5x 9v Battery Adapter Connector 6F22 with Cable features: - Cable 15cm long - Battery connector 9V, 6F22 Code PP013 Available Price €0.55
Battery holder 2x 18650 PCB mount Base of two 18650 batteries to solder on PCB. Characteristic: - Measurements 78x 40x 21mm - Weight: 10 gr . (approx.) - Stack length max 67mm Code PP052 Available Regular price €2.49 -€0.40 Price €2.09
Battery holder 1x 18650 PCB mount 18650 battery base for soldering to PCB. Characteristic: - Measurements 78x 20x 21mm - Weight: 10 gr. ( approx.) - Stack length max 67mm Code PP053 Available Regular price €1.99 -€0.30 Price €1.69
Battery holder 4x AAA 6V Characteristic: - Cable 13cm long - Measurements 49x 52x 13mm - Battery length max 44mm - Compatible batteries (LR03, 24A, R03, RX03, MN2400, AM4, UM4) Code PP001 Available Price €1.19
Battery holder 2x 18650 3,7V Parallel Lithium Battery Instruction: - The drawing of the polarities is not correct, it is wrong - Put the batteries in parallel Characteristic: - Cable 15cm long - Measures 74x42x 20mm - Weight: 10 gr. (Approx.) - Stack length max 67mm Code PP016 Available Price €1.85