Panasonic rechargeable battery NCR18650B 3400mAh Li-ion

This Reed switch module uses a small device called a reed switch.
When the device is exposed to a magnetic field, the two ferrous materials inside the switch come together and the switch closes. When the magnetic field is removed the switch opens. The operating mode: - When exposed to a magnetic field the DO output is high
- Power supply: 3.3-5V
- Contact type: SPST-NO (normally open)
- Use temperature: -20ºC to + 80ºC
- Type Output: Digital (1 - 0)
- PCB dimensions: 32 x 14 mm

Descripción:
Chip XL4015 - Upgrade of the LM2596
Drop module
Use a multimeter to check the output voltage and adjust the potentiometer
Voltage control
XL4015 DC Voltage Converter 5A 75W Step Down Regulator DC LM2596 features:
- Input voltage: 4.5V-38V
- Output voltage: 1.25-36.5V
- Current output: 4.5A (max 5A)
- Output power: 75W maximum
- Operating temperature: -40 to + 85 ºC
- Operating frequency: 180KHz
- Efficiency conversion: up to 96%
- Short circuit protection: Yes (limited current 8A)
- Protection over temperature: the output switches off automatically
- Size: 62mm x 38mm x 15mm
Principal functions:
- Step-down converter with overcurrent protection
- Li-Po battery charger, Li-Ion

This Step-down voltage converter includes 5 functions in one module. It can be used as a voltmeter, ammeter and measurements can be recovered through its USB port.
The output voltage and voltage can be adjusted thanks to two potentiometers present in the module.
It has an efficiency Very high, it has a display screen for voltage, current and two buttons to configure what you want to see. Characteristic: - Voltage of input: 5.5 - 36 V
- Output voltage: 1.25-32 V continuously adjustable
- Output current: 4.5 A (Max 5A for a short time) adjustable with potentiometer,
- Power output: 75 W maximum (recommended to use 50 W, large pressure difference, please reduce power)
- Operating temperature: -40 ° C - + 150 ° C

Descripción: Light sensor module to measure light intensity and obtain digital data from it.
Ideal for projects with ARDUINO.
You can use it with PIC, AVR, STM32.
BH1750FVI (Rohm) is used to adjust backlighting of LCD screens and keyboards by manufacturers of mobile phones, digital cameras, navigation and portable gaming devices. Light Sensor Module BH1750 FVI Arduino Raspberry features:
- Chip BH1750FVI
- Supply voltage 3V-5V
- Integrated 16bit AD converter
- Detection range: 0-65535 lx (with an accuracy of 1 lux)
- Interface: II2C
- Low dependence on the light source (eg incandescent lamp, fluorescent lamp, halogen lamp, white LED, sunlight)
- Dimensions 18.4 x 14 mm

Load cell Load Cell Weight Sensor 2kg features:
- Load cell to measure weight up to 2kg
- The transducer measures the deformation of the metal structure and converts it into a few mV
- Load range: 2kg
- Operating voltage: 3VDC ~ 14 VDC
- Nominal output: 1.0 ± 0.15mV / V
- Repeatability: 0.03% FS
- Effect of the temperature at the outlet: 0.01% F.S / °C
- Effect of temperature on zero: 0.05% F.S / °C
- Zero: ± 0.1000 mV / V
- Input impedance: 1115 + -10% Ω
- Output impedance: 1000 + - 10% Ω
- Insulation resistance:> = 1000 MΩ
- Safe Overload Rate: 150% FS
- Final overload rate: 200% FS
- Temperature range: -20 - 60 °C
- Material: Aluminum alloy
- Degree of protection: IP65

Female Strip 40 Short Pins features:
- Pin spacing: 2.54mm
- Insert position: Vertical
- Insert: Pasante
- Quantity: 1 unit of strips of 40 female pins each

A preparation to remove oxides and sulphites from electrical contacts and to provide protection against corrosion, ensures the flow of electricity especially in case of rusty or worn contacts.
It can be used in audio products - low frequency and high, electronic industry and in other places where clean contacts are required.
For cleaning contacts, electrical terminals, alternators, switches, plugs, sockets integrated circuits, lampholders, fuseholders, capacitor contacts, flowmeters etc. 400ml Electrical Contacts Cleaner Spray + Brush features:
- Restores low resistance in connections
- Used in audio technologies
- Protection against moisture and corrosion
- High quality - manufactured in EU

Cable Chain 10x10 1m for 3D CNC Printer features:
- Suitable for movements where cable displacement or twisting is needed, where cable protection is needed - Easy for installation And maintenance; Low noise, high speed wear resistant movement - The cable structure has been widely used in CNC machine tools, electronic equipment, fire fighting machinery and equipment, stone machinery, machinery glass, doors and windows of machines, injection molding machines, robots, overweight transport equipment, automated warehouses - Interior widths 10x10mm
- Exterior measurement 15x20mm
- Material: reinforced series polyamide
- Length: 1m
- Quantity: 1 unit