Qwiic cable protoboard - 4 pin This cable is an essential element of the Qwiic ecosystem - it enables connection between the protoboard and any device with a Qwiic connector. With all the benefits of Qwiic at hand - no soldering required, easy 1-second hookup on click and dismantling. The cable is 150mm long. Wires are color coded according to scheme: Code SP020 Available Price €1.99
DS18B20 Probe 2m Submersible Temperature Sensor Encapsulated with water resistant stainless steel with sensor dimensions 5.5*50mm, cable length 200 cm. DS18B20 Probe 2m Submersible Temperature Sensor features:- Based on the DS18B20 chip- Supply voltage: 3 ~ 5.5V- Consumption <5mA- Measuring Range: -55 °C to 125 °C- Accuracy: +/- 0,5ºC- Outputs: - GND black - Vcc red - Yellow digital output- Inocidable steel- Cable length: 2m Code S0015 Available Price €3.79
Kit Funduino I/O Expansion starter kit for Arduino UNO Kit Funduino I / O Expansion starter kit for Arduino UNO R3.Kit 37 Sensors in a Box for Arduino features: Including the referencias of módulos siguientes: - 1x módulo Funduino I / O Expansion- 1x módulo zumbador activo Keyes- 1x módulo foto resistencia Keyes- 1x módulo sensor of temperatura Keyes- 4x módulos sensor LED sombrero of Keyes paja- 1x módulo sensor of sonido Keyes- 1x módulo sensor Rotation Keyes- 1x pulsador módulo- 1x distancia sensor HC-SR04- 1x módulo Joystick Doble 2 Ejes XY- 1x servo 9g SG90- 9x Dupont cables con conector 3 pins- 20x Hembra-Macho Cables 20cm- 1x USB cable for Arduino UNO Tipo A-B 50cm Helpful Links:Install the IDE Arduino development interface Code B0056 Available Price €38.90
UNO Board CH340 clone - It has an Atmega328P chip running at 16Mhz with factory-loaded bootloader- The Uno R3 module has all the Arduino Uno R3 connectors and is compatible with all Arduino shields Characteristic: - ATmega328P 16MHz chip with external quartz crystal- Microprocessor: ATMega328P- Operating voltage: 5V- Input voltage (recommended): 7-12V- Input voltage (limits): 6-20V- Clock speed: 16 MHz- Digital I / O pins: 14 (6 with PWM)- Analog input pins: 6- DC current for Pin I / O: 20 mA- Flash32 KB of which 0.5 KB are used by the bootloader - AtMega328P- SRAM 2 KB - AtMega328P- EEPROM 1 KB - AtMega328P- Communication: USB female Type B Code B0011 Available Price €7.49
NRF24L01 Shield Atmega48 Wireless Module SPI To IIC I2C TWI Interface NRF24L01 Shield Atmega48 Wireless Module SPI To IIC I2C TWI Interface features: - Operating voltage: 5V- Wait time of the module receives the data: more than 2S- The waiting time of the module sends data: more than 300- Transfer speed: 50 Byte / S (theoretical value)- I2C / TWI address: 0 x 47 (decimal 35)- Address NRF24L01: 0 x 34, 0 x 43, 0 x 10, 0 x 10, 0 x 01 (from lowest to highest)- Size: 44 x 23 mm Code W0066 Available Price €4.46
Qwiic cable 50mm It is a basic cable for connection of Qwiic elements featuresd with two JST 1mm connectors. The Qwiic cables are color coded and the connector is polarized making it easy and quick to connect the components. The cable is 50mm long Code SP040 Available Price €1.19
Arduino compatible Due R3 SAM3X8E board It has an Atmel SAM3X8E ARM Cortex-M3 chip running at 84Mhz with a factory-loaded bootloader with 54 digital input / output (of which 12 can be used as PWM outputs), 12 analog inputs, 4 UART (hardware serial ports). The board includes a USB connector, a SPI port, a reset button, a button erase and some status LEDs. Atmega16U2 programmed as a USB / Serial converter for power, simply connect it to a computer with a USB cable or power with a power adapter and DC connector. Characteristic: Operating voltage: 3.3V Input voltage (recommended): 7-12V Digital I / O Pins: 54 (12 PWM outputs) Analog input 12 pins 2 x DAC 2 x TWI 4x UART DC current per DIGITAL I / O pin 130 mA Flash: 512 KB Code B0028 Last items in stock Price €44.95
LM35DZ Temperature Sensor TO-92 LM35 Temperature Sensor LM35DZ TO92 features:- The output is linear and each degree Celsius equals 10 mV- Power supply from 4 to 30 Vdc- Connection through analog input- Temperature range from 0ºC to 100ºC- Linearity +10 mV / ºC- Quantity: 1 unit Code S0016 Available Price €2.49
Makey Makey Classic Contents Makey Makey Board USB Cable 7 Alligator Clips 6 Connector Wires Instructions with Visual Project Start Guide Online Documentation 20 Color Stickers Start out easy with a banana piano. First setup takes seconds. Then make games controllers, musical instruments, and countless inventions. Advance to additional inputs and multi-key remapping up to 18 keys.Turn everyday objects like bananas into touchpads! Connect the world around you to your computer! Setup takes just seconds. Just plug, clip, and play! No programing knowledge needed. No software to install. Works with Mac and Windows.1000s of possibilities! Draw your own game controller, sneak a cat selfie, and dance like never before.Ages 8 to infinity. Code B0101 Last items in stock Price €69.95
SD Card Module Reader The SD card reader module is a simple solution for transferring data to and from a standard SD card.The pinout is directly compatible with Arduino, but it can also be used with other microcontrollers.SD Card Module Reader features:- Supply voltage: 3.3V or 5V - Interface: SPI 3.3V- Dimensions: 30mm x 50mm x 12mm Code M0023 Available Price €0.99
Qwiic cable 100mm It is a basic cable for connection of Qwiic elements featuresd with two JST 1mm connectors. The Qwiic cables are color coded and the connector is polarized making it easy and quick to connect the components. The cable is 100mm long Code SP022 Available Price €1.99
Relay SRD-05 DC-2P 5V 10A SPDT - SRD-05VDC-SL-C Relay SRD-05 DC-2P 5V 10A SPDT features:- Supply voltage: 5V- Output Current: 10A- For power switching with 5V DC signals - Microcontroller, Arduino, Electronica Code RL011 Available Price €0.69
UNO Board CH340 micro USB clone - It has an Atmega328P chip running at 16Mhz with factory-loaded bootloader- The Uno R3 module has all the Arduino Uno R3 connectors and is compatible with all Arduino shields Characteristic: - Includes USB Cable- ATmega328P 16MHz chip with external quartz crystal- Microprocessor: ATMega328P- Operating voltage: 5V- Input voltage (recommended): 7-12V- Input voltage (limits): 6-20V- Clock speed: 16 MHz- Digital I / O pins: 14 (6 with PWM)- Analog input pins: 6- DC current for Pin I / O: 20 mA- Flash32 KB of which 0.5 KB are used by the bootloader - AtMega328P- SRAM 2 KB - AtMega328P- EEPROM 1 KB - AtMega328P- Communication: micro USB female Type B Code B0053 Available Price €9.59
TFT LCD Expansion Board Adapter V2.2 40pins 3.2" 4.3" 5.0" Shield Mega2560 TFT LCD 40pins Expansion Board Adapter 3.2" 4.3" 5.0 Shield Mega 2560 features:- Facilitates connections between the LCD TFT Touch 3V 2.4 ", 2.8", 3.2 "etc. with SD card reader and the Arduino Mega 2560 board- Put the screen on the Shield and you can connect it directly to the Arduino Mega2560.- TFT LCD MFT TFT LCD PCB adapter for Arduino Mega2560 STM32- The TFT01 LCD operates at 3.3V and can not be used directly on the standard Arduino motherboard at the top.- The TFT LCD PCB adapter for Mega is compatible with the Arduino pins, the user can directly connect the TFT LCD PCB - Adapter on the shield and stand on the Arduino board. It can be used with a Mega2560 and LCD screen. Code P0158 Available Price €7.90
Analogical Acoustic Sensor 4-Pin Microphone Sound Detector Module Sound detection module for Arduino projects, smart cars. Analogical Acoustic Sensor 4-Pin Microphone Sound Detector Module features: - Adjustable High Sensitivity Acoustic Sensor - LM393 comparator chip - Integrated indicator LED - AO analog output, output voltage signal in time real microphone - DO digital output, sensitivity adjustable through potentiometer - Frequency Range between 30 and 15000 Hz - Power 4 ~ 6V - Measurements 36x16x15mm Code S0017 Available Price €1.79
Kit Mega XXL Darwin for Arduino Perfect "Mega XXL Darwin Kit" to learn programming and electronics with Arduino. It allows you to build various projects of varying complexity, from the easiest... to the most complicated. The elements are placed in the box to keep everything in order. Code B0071 Available Price €53.99
Matrix Membrane Keyboard 4x4 Modulo High-quality membrane keyboard, with 16-key matrix, ultra-thin, less than 1mm thick, with adhesive system on the reverse side. Ideal for your Arduino projects, but can also be used with other microcontrollers. Matrix Membrane Keyboard 4x4 Modulo features: - Rating circuit, Max: DC 35V 100 mA - Cable length: 85 mm - Dupont 8 pin connector - Specific insulation: 100 M Ohm, 100V - Useful life: + 1 million uses - Contact parting: Code M0025 Available Price €1.79
Arduino PORTENTA Breakout Board The Portenta Breakout module extends the capabilities of the Arduino Portenta module with additional connectors and cables. The module includes a power switch, a DIP switch for selecting the start mode of the Arduino Portenta, as well as a series of connectors: USB A, RJ5, microSD, OpenMW, MIPI 20T JTAG. The board also includes the RTC chip, as well as a slot for the CR2032 battery, a screw connector for the power supply and all the cables for the Arduino Portenta module. Code ASX00031 Available Regular price €54.95 -€4.96 Price €49.99
Current Sensor ACS712 AC/DC 30A for Arduino Sensor used to measure the current in the circuit to which it is connected. Characteristic: - Output: Analog - Power: 5V - Accuracy: 1.5% - Measuring capacity: +/- 30A - Dimensions: 31 x 13 mm Code M0028 Available Price €3.39
Relay SRD-12 DC-2P 12V 10A SPDT Relay SRD-12 DC-2P 12V 10A SPDT features:- Supply voltage: 12V- Output Current: 10A- Relay activation current: 15mA ~ 20mA- For power switching with 12V DC signals - Microcontroller, Arduino, Electronica Code RL012 Available Price €0.98
DHT11 Temperature and Humidity Sensor The humidity sensor DHT11 comes in a plastic body ideal for mounting on a panel or similar. It uses a capacitive sensor that returns a digital signal with the measurement. DHT11 Temperature and Humidity Sensor features: - Operating voltage: 3 to 5 VDC- Humidity measurement range: 20-95% ± 5% accuracy- Temperature measurement range: 0ºC to 50ºC ± 2º accuracy- Maximum sampling rate: 2 seconds- Working current 2.5mA- Iterfaz 1-wire- Dimensions: 2.3 x1.2x 0.5cm- Quantity: 1 unit Code S0010 Available Price €2.49
4-Channel 5V 10A Relay Module Characteristic: - Channels: 4 (independent protected by Optocouplers) - Supply Voltage: 5V - Output Current: 10A - Relay activation current: 15mA ~ 20mA - Isolation: Yes - Indicator LED: For each channel - Dimensions: 54x 72mm - 5V Optocoupled 4-Channel Relay Module - This module can be directly controlled by the microcontroller (Arduino, 8051, AVR, PIC, DSP, ARM, ARM, MSP430, TTL) Useful links for Arduino / Raspberry programming and projects with Arduino / Raspberry boards: User manual for the remote control + 4-channel 315 MHz IC2262 receiver: - Relay Module Programming 5V 10A 4 Channel with remote control + 4 channel receiver Code RL007 Available Price €3.99
UNO WIFI Board CH340 compatible Arduino, NodeMCU, WeMos ESP8266 - It has an Atmega328P chip running at 16Mhz with factory-loaded bootloader- The Uno R3 module has all the Arduino Uno R3 connectors and is compatible with all Arduino shields Characteristic: - ATmega328P 16MHz chip with external quartz crystal- Microprocessor: ATMega328P- Operating voltage: 5V- Input voltage (recommended): 7-12V- Input voltage (limits): 6-20V- Clock speed: 16 MHz- Digital I / O pins: 14 (6 with PWM)- Analog input pins: 6- DC current for Pin I / O: 20 mA- Flash32 KB of which 0.5 KB are used by the bootloader - AtMega328P- SRAM 2 KB - AtMega328P- EEPROM 1 KB - AtMega328P- Communication: micro USB female Code B0070 Available Price €11.99
Kit XXL Sensors for Arduino compatible Perfect "Kit XXL Sensors" to learn programming with Arduino, the basis of electronics. It allows to build various projects of various complexity, from the easiest ... to the most complicated. The elements are placed in the box to keep everything in order. The kit does not include an Arduino board. An original Arduino board or a Chinese equivalent can be purchased separately. Code B0115 Available Regular price €60.29 -€17.70 Price €42.59
DHT22/AM2302 Temperature Sensor Humidity PCB + Digital Cable for Arduino - The DHT22 humidity sensor is presented in a plastic body ideal for mounting on a panel or similar. It uses a capacitive sensor that returns a digital signal with the measurement - This sensor, unlike DHT11, is capable of measuring negative temperature values and measures tenths of a degree Characteristic: - Operating voltage: 3 to 5.5 VDC - Humidity measurement range: 0-100% ± 2% accuracy - Temperature measurement range: -40ºC to 80ºC ± 0.5º accuracy - Maximum sampling rate: 2 seconds Useful links for Arduino / Raspberry programming and projects with Arduino / Raspberry boards: Write texts on the OLED 0.96 '' screen - Read the measurements of the temperature / humidity sensor DHT22 / AM2302 on a 0.96 '' OLED screen Send /> Code M0099 Available Regular price €6.49 -€2.00 Price €4.49
Arduino Multifunction shield - Display, LEDs, pushbuttons, buzzer Getting started with Arduino? This multi-function shield for Arduino UNO is ideal for your first Arduino DIY projects. It includes 4 7-segment displays, buzzer, 3 push buttons, 4 LEDs, potentiometer and sockets. Code M0230 Available Price €4.89
Starter Kit XL Arduino compatible Perfect kit to learn programming in the middle of Arduino the basic of electronics It allows to build various projects of various complexity, from the easiest ... to the most complicated.The elements are placed in the box to keep everything in order. The kit does not include an Arduino board. An original Arduino board or a Chinese equivalent can be purchased separately. Code B0116 Available Regular price €56.20 -€17.39 Price €38.80
M12 Inductive Proximity Sensor PNP DC 6-36V LJ12A3-4-Z/BY 3D Printer M12 Inductive Proximity Sensor PNP DC 6-36V LJ12A3-4-Z/BY 3D Printer features: - This sensor can be configured as auto Z axis level - Sensor detection switch inductive proximity LJ12A3-4-Z / BY - PNP DC6-36V - Often used for 3D printer bed leveling - Typical application: printer bed level sensor 3D - Cylindrical cable type DC 3 cable type (black, brown, blue) - Inductive sensor type - PNP NO (Normal Open) - Detecting Distance 4mm - DC supply voltage 6-36V - Current output 300mA - Response frequency 0.5KHz - Detects iron / aluminum - Operating temperature -25 ° C at + 55 ° C (Non-freezing condition) - Head diameter 12 mm - Size 6.2 x 2cm - Cable length 100cm Code S0036 Available Regular price €3.99 -€0.50 Price €3.49
Sensor Module Infrared Obstacle Detector Car Robot Ideal for projects with ARDUINO, Smart Car. Sensor Module Infrared Obstacle Detector Car Robot features: - Power supply: 3.3 - 5V DC - OUT level 0/1 output - Sensitivity adjustment - Power LED - Distance from detection: 2 - 30cm (max60cm) - detection angle: 35º - LED output status indicator - Dimensions: 40x13x8mm Code S0011 Available Price €1.49
Relay Module DC 12V 10A 1 Channel Low/High Trigger Relay Module DC 12V 10A 1 Channel Low/High Trigger features:- Channel: 1 (protected with Optocoupler)- Supply voltage: 12V- Output Current: 10A- Relay activation current: 15mA ~ 20mA- Insulation: Yes- Trigger signal type jumper (low / high)- LED indicator- Dimensions: 30x 54mm- Has a jumper that allows to choose type of trigger signal (low / high) Code RL003 Available Price €2.29
MQ-2 Gas and Smoke Module Sensor Detector Methane Propane Butane LPG MQ-2 Gas and Smoke Module Sensor Detector Methane Propane Butane LPG features: - Main chip: MQ-2 flammable gas and smoke sensor and comparator LM393- Working voltage: 5V- Current: 150mA- Digital output: TTL 0/1- Analog output: analog voltage sensing value- Quick response features:- Concentration detection: 200ppm - 5000ppm LPG, propane 300ppm - 5000ppm butane 5000ppm - 20000ppm methane 300ppm - 5000ppm H2 100ppm -2000ppm alcohol- Adjustable sensitivity with the potentiometer- Size: 32mm x 20mmx 18mm Code S0027 Available Price €2.89
W1209 12V DC Thermostat Digital Temperature Controller Switch W1209 12V DC Thermostat Digital Temperature Controller Switch features: - Model: W1209 - Supply voltage: DC 12V - Temperature control mode: ON / OFF - Temperature range: -50 -110 ° C - Resolution: 0.1 ° C range -9.9 ~ 99.9 ° C, above is 1 ° C - Measurement accuracy: 0.1 ° C - Refresh rate: 0.5 s - Temperature protection 0-110 ° C - Static current: ‰ ¤ 35mA, working current ‰ ¤ 65mA - Power of output: 10A relay - Sensor probe: NTC waterproof sensor (10K 0.5%) - Environmental requirements: -10 ~ 60 ° C Humidity 20% -85% - Dimensions: 48 x 40 mm Code M0102 Available Price €3.79
MQ-4 Gas Methane Sensor Module for Arduino MQ-4 Gas Methane Sensor Module for Arduino features:- Main chip: MQ-4 methane sensor and comparator LM393- Working voltage: 5V- Current: 150mA- Digital output: TTL 0/1- Analog output: analog voltage sensing value- Quick response features:- Detection concentration:200ppm- 10000ppm CH4, natural gas- Adjustable sensitivity with the potentiometer- Size: 32mm x 20mmx 18mm Code S0028 Available Price €2.95
MyoWare Shield - Mini protoboard for MyoWare sensor Simple breadboard for your MyoWare Muscle Sensor. You can use the provided area of the shield to solder in any custom circuit you can think of. This shield provides 8 x 15 solderable through holes on a standard 0.1" grid. Code SP070 Last items in stock Price €3.29
MG-5 Gas Methane Sensor Module for Arduino MG-5 Gas Methane Sensor Module for Arduino features: - Main chip: MQ-5 natural gas sensor and comparator LM393- Working voltage: 5V- Current: 150mA- Digital output: TTL 0/1- Analog output: analog voltage sensing value- Quick response features:- Detection concentration:- 200ppm - 10000ppm LPG, LNG, natural gas, propane,- Adjustable sensitivity with the potentiometer- Size: 32mm x 20mmx 18mm Code S0029 Available Price €2.53
Arduino Engineering Kit REV2 The Arduino Engineering Kit Rev 2 is a versatile and practical learning tool. By creating fun, real-world projects, you can understand basic engineering and mechatronics concepts and learn to program in MATLAB and Simulink. The versatility of the elements gives you the opportunity to adapt the content and create your own curriculum based on it. The kit includes online courseware, step-by-step instructions, lessons and exercises. It works best when studying in small groups. Code AKX022 Available Regular price €289.95 -€15.00 Price €274.95
Relay Module 1 Channel 5V 10A 1 Channel 5V Relay Module. This module can be directly controlled by the microcontroller (Arduino, 8051, AVR, PIC, DSP, ARM, ARM, MSP430, TTL). Relay Module 1 Channel 5V 10A features: - Channel: 1 - Supply Voltage: 5V - Output Current: 10A - Relay activation current: 15mA ~ 20mA - LED indicator - Dimensions: 30x 54mm Code RL005 Available Price €1.29
Kit de Pro Mini Atmega328 5V 16M + Adaptador USB-UART CP2102 para Arduino Set of Pro Mini Atmega328 5V 16M + USB-UART Adapter CP2102 for Arduino Pro mni has an Atmega328P chip running at 16Mhz with a factory-loaded bootloader. It does not include pins so we can solder only the pins we need. Ideal for connecting TTL RS232 devices to your PC through the USB port. Code B0018 Available Price €12.65
MPU-6050 Accelerometer Module + Gyroscope 3 Ideal for projects with ARDUINO.You can use it with PIC, AVR, STM32. MPU-6050 Accelerometer Module + Gyroscope 3 features:- Chip: MPU-6050- Power supply: 3V-5V- Operating current: 5mA- Communication: I2C- 16-bit analog-digital converter on all axes- Gyroscope scales: ± 250, ± 500, ± 1000 and ± 2000 ° / sec (dps) (programmable by the user)- Accelerometer scales: ± 2g, ± 4g, ± 8g and ± 16g (programmable by the user)- Dimensions: 14 x 21 x 1.3mm- Quantity: 1 unit (1 strip of 8 pin + 1 strip of 8 layered pin) Code M0017 Available Price €4.29
Sensor Cable - Electrode Pads (3 connector) This is your simple three conductor sensor cable with electrode pad wires. These cables measure 24" long and feature a 3.5mm audio jack on one end with snap type receptacles for biomedical sensor pads. Code SP075 Available Price €8.99
SparkFun Qwiic Adapter This little board is simply a I2C board to Qwiic converter. It pretty much enables any device with I2C connectors to work with Qwiic system. It has two Qwiic ports - both of them served with the same I2C bus. You simply stick the board on your I2C board and get additional two Qwiic ports. It is as easy as it sounds Code SP033 Available Price €1.89
Relay Module DC 5V 10A 2 Channel Low/High Trigger Relay Module DC 5V 10A 2 Channel Low/High Trigger features:- Channels: 2 (independent protected with Optocouplers)- Supply voltage: 5V- Output Current: 10A- Relay activation current: 15mA ~ 20mA- Insulation: Yes- Trigger signal type jumper (low / high)- LED indicator: For each channel- Dimensions: 40x 50mm- It has a jumper that allows to choose type of trigger signal (low / high)- This module can be controlled directly by the microcontroller (Arduino, 8051, AVR, PIC, DSP, ARM, ARM, MSP430, TTL) Code RL002 Available Price €3.15
Rain Sensor Module Water Droplet Detector The module has two outputs: analog A0 and digital D0. digital output D0 - signal 0 or 1 appears depending on the configuration of threshold. The threshold is fixed with the potentiometer. Characteristic: - Operating voltage: 3.3V -5 V - Sensitivity adjustable by potentiometer - Dual output mode: analog and digital - Red LED - power indicator - Green LED - digital switching output indicator - Measurements PCB: 3 x 1.5 cm - Sensor measurements: 5.4 x 3.9 cm Code S0022 Available Price €1.69
XM-15B Bluetooth Serial Port Module Master Slave Arduino compatible HC-05/06 XM-15B Bluetooth Serial Port Module Master Slave Compatible Arduino HC-05/06 features: * Power 3.0V -6V* 3.3V / 5V logic levels* Bluetooth version V2.1 + EDR* Frequency: 2.4GHz ISM band* Reach approx. 30m* Security: Authentication and encryption* Supports AT commands for configuration through a serial port* Working temperature: -20 ºC to +75 ºC* Working current - 50 mA* PCB dimension: 35 x 19m -Using the conventional Bluetooth CSR chip, the protocol standard Bluetooth V2.1 + EDR, passes the Bluetooth BQB certification-Fast start, only 0.3 seconds to complete the initialization of the complete module (including the Bluetooth protocol stack)- Built-in hardware protector, never hangs Code W0022 Available Price €7.49
Water Level Sensor Module One Mega Pic Easily convert water level to analog signal The analog output signal can be read directly on the Arduino board Characteristic: - Operating voltage: 3.3V -5 V - Consumption: less than 20 mA - Sensor type: Analog - Operating temperature: 10º C -30º C - Detection area: 40 mm x 16 mm - Dimensions: 60 mm x 20 mm Code S0023 Available Price €1.39
MyoWare 2.0 Cable Shield This Cable Shield provides a 3.5mm connector where you can connect a three-electrode sensor cable, allowing you to test and use the MyoWare 2.0 muscle sensor without actually connecting it to your person. Code SP045 Available Price €7.49
ESP8266 WiFi Motor Drive L293D Expansion Shield Board ESP12E NodeMcu Allows control: - Up to 2 bidirectional current motors- Or 1 stepper motor Shield is compatible with NodeMcu ESP8266 CP2102 WIFI Development Board ESP8266 WiFi Motor Drive L293D Expansion Shield Board ESP12E NodeMcu features: - Minimum operating voltage: 4.5 V- Maximum operating voltage: 36 V- Maximum current: ± 1.2 A- Logic voltage: - 2.3V <= HIV <= VIN (high) - 0.3V <= VIL <= 1.5V (low)- Controller L293D- Measures: 58x42 mm ESP12 port control kit: - D1, D3 - motorA- D2, D4 - motorB Code W0015 Available Price €3.49
DHT11 Module Temperature and Humidity Sensor The DHT11 humidity sensor is presented in a plastic body ideal for mounting on a panel or similar. It uses a capacitive sensor that returns a digital signal with the measurement. Characteristic: - Operating voltage: 3 to 5 VDC - Humidity measurement range: 20-95% ± 5% accuracy - Temperature measurement range: 0ºC to 50ºC ± 2º accuracy - Maximum sampling rate: 2 seconds - Working current 2.5mA - 1-wire interface - Dimensions: 32 x14 mm - Quantity: 1 unit with 3x female / female cables Code S0001 Available Price €2.99
ST-LINK V2 Mini STM8 STM32 Simulator Programmer ST-LINK V2 Debugger / chip programmer for STM8 and STM32, supports SWIM and JTAG Serial Wire interfaces. Code B0117 Available Price €11.50
Qwiic cable kit The SparkFun Qwiic Cable Kit includes 10 cables of different lengths and styles that will connect your Qwiic boards to each other, to a development platform or to a breadboard. Each Qwiic cable is colour coded red, black, blue and yellow with 1mm JST termination. Code SP098 Available Price €11.95
HB100 Microwave Doppler Radar Motion Sensor Microwave motion detector module. The main applications may be security alarms and sensors, systems Automatic doors, ATM machines, car reverse systems, light sensors, can also be used for traffic monitoring and control applications. High resistance to radio frequency interference. Characteristic: - Frequency: 10.525GHz - Frequency Accuracy: 3MHz - Minimum Output: 13dBm EIRP - Operating Voltage: 5V ± 0.25V - Operating current (CW): 60mA maximum, 37mA typical - Harmonic emissions: -10dBm - Detection Range: Over 20 meters - Power of Output: 5mW The device is sensitive to electrostatic discharge and can be damaged during welding. The IF output is particularly sensitive. Code M0026 Available Price €5.44
Gravity: Huskylens - An easy-to-use AI camera | vision sensor Huskylens is an easy-to-use AI camera and vision sensor. DFrobot Huskylens (SEN0305) is equipped with multiple functions, such as face recognition, object tracking, object recognition, line tracking, colour recognition and label recognition (QR code). Code DF013 Available Price €71.49
SparkFun DataLogger IoT - 9DoF SparkFun DataLogger IoT - 9DoF is a pre-programmed data logger to automatically log IMU, GPS and various pressure, humidity and distance sensors - all without having to write a single line of code! DataLogger automatically detects, configures and logs Qwiic sensors. It is specifically designed for users who only need to capture a large amount of data in a CSV or JSON file and return it to their larger project. Code SP099 Last items in stock Price €94.90
ESP8266 5V WiFi Relay Module AP Remote Control + STA You can easily control any device over the Internet through your phone, computer, etc. The module can handle 5 users at the same time, it can work in two modes: STA (client) and AP (access point). In AP mode, the module is connected via WIFI directly to your phone or computer (in open field can be up to 300 meters). In STA mode, the relay module is connected to the access point (router) that supplies the network. Wi-Fi in the room where the relays are located. In this case, the range mainly depends on the power of the access point antennas (routers). You should not turn off after the configuration is completed, as some of the parameters of the WIFI module cannot be saved when power is cut off. Code W0067 Available Price €9.49
MQ-135 Air Quality Sensor High sensitivity to Ammonia (NH3), Nitrogen oxides (NOx), Alcohol, Sulphides, Benzene (C6H6), CO2, smoke and other harmful gases. The MQ-135 sensor is to sensible for other gasses in the air so that is not possible to get good values for CO2 from it. MQ-135 Air Quality Sensor features:- Main chip: MQ-135 natural gas sensor and comparator LM393- Working voltage: 5V- Current: 150mA- Digital output: TTL 0/1- Analog output: analog voltage sensing value- Quick response features:- Detection concentration: 10ppm - 300ppm NH3 10ppm - 1000ppm Benzene 10ppm - 300ppm Alcohol- Adjustable sensitivity with the potentiometer- Size: 32mm x 20mmx 18mm Code S0034 Available Price €2.45
MQ-9 Carbon Monoxide Sensor Module MQ-9 Carbon Monoxide Sensor Module features:- Main chip: MQ-9 methane sensor and comparator LM393- Working voltage: 5V- Current: 150mA- Digital output: TTL 0/1- Analog output: analog voltage sensing value- Quick response features:- Detection concentration: 20ppm- 2000ppm carbon monoxide 500ppm- 10000ppm methane CH4 500ppm- 10000ppm LPG- Adjustable sensitivity with the potentiometer- Size: 32mm x 20mmx 18mm Code S0033 Available Price €2.89
Gravity: Huskylens PRO - An easy-to-use AI camera | vision sensor Huskylens PRO is an easy-to-use AI camera and vision sensor. DFrobot Huskylens (SEN0336) is equipped with multiple functions, such as face recognition, object tracking, object recognition, line tracking, colour recognition and label recognition (QR code). Code DF020 Last items in stock Price €95.95
Lilypad Battery Support Button Cell 3V CR2032 Lilypad Battery Support Button Cell 3V CR2032 features: - Battery holder for your Lilypad projects - For 20mm diameter battery type CR2032 - ON / OFF control - Connection points: 4 Code M0072 Available Regular price €3.99 -€1.00 Price €2.99
Buzzer 5V Active Buzzer 4 to 7V DC Buzzer alarm to convert electrical to acoustic signals in robotics devices and Arduino projects. Buzzer 5V Active Buzzer 4 to 7V DC features: - Input voltage: 4V to 7V - Diameter: 12mm - Height: 9.5mm - Spacing Pins: 7.6mm - Maximum Current: Code M0007 Available Price €0.45
MQ-8 Hydrogen Gas Sensor Module MQ-8 Hydrogen Gas Sensor Module features:- Main chip: MQ-8 methane sensor and comparator LM393- Working voltage: 5V- Current: 150mA- Digital output: TTL 0/1- Analog output: analog voltage sensing value- Quick response features:- Detection concentration: 100ppm- 10000ppm hydrogen H2- Adjustable sensitivity with the potentiometer- Size: 32mm x 20mmx 18mm Code S0032 Available Price €2.95