Arduino Modules

SIM900 Four Band GSM GPRS Module with Antenna shield for Arduino features:
- GSM / GPRS SIM900 module-based development card / shield from Simcom
- The shield allows you to get SMS, MMS, GPRS and audio via UART by sending AT commands (GSM 07.07, 07.05 and SIMCOM Enhanced COM Commands).
- The shield also has 12 GPIOs, 2 PWMs and a ADC of the SIM900 module (All of them are 2V8 logic) present on board.
- Quad-Band 850/900/1800/1900 MHz: it would work on GSM networks in all countries of the world. - GPRS multi-slot class 10/8
- GPRS mobile station class B
- Complies with GSM phase 2/2 +
- Class 4 (2 W @>

GSM A6 Four Band GPRS Module with MCU Antenna features:
- GSM / GPRS module / development board / shield based on GPRS A6
- Supports GSM / Dual band GPRS, available for remote GPRS and SMS data transmission
- Compact size and low current consumption
- With energy saving technique, current consumption is as low as 5mA (sleep mode)
- Communicates with the microcontroller through the UART port, supports the command including GSM 07.07, GSM 07.05 and Ai-Thinker Enhanced AT Commands
- Working frequency: four-band network, 850 / 900/1800 / 1900MHz
- Operating voltage: 4.8-9VDC (Supply power of the on-board regulator circuit for the A6 module)
- Working current: 2A maximum
- Current Sleep: 5mA

NFC module for Educational STEAM Kit.  Near field communication (NFC) is a set of standards for smartphones and similar devices to establish radio communication with each other by touching them together or bringing them into close proximity, usually no more than a few centimeters. Compatible with almost any microcontroller, Arduino, PIC, AVR. It can be used in Access Control projects and Alarm projects. RFID PN532 NFC Module with Card and Pendant features:
- Support i2C, SPI, High Speed UART - Support RFID reading and writing - Support P2P communication with peers - Support NFC with phone - Work in NFC Mode or RFID reader/writer Mode - RFID reader/writer supports: - 1k, 4k, Ultralight, and DesFire cards ISO/>

The piezoelectric buzzer has a simple structure in which a ceramic piezoelectric disk is affixed to a vibrating plate. An alternative voltage applied to this element will cause a contraction or diametrical expansion of the element. This feature is used to fold a vibrating plate, which generates sounds. Passive Buzzer 5V features:

- Input voltage: 3V to 12V
- Diameter: 12mm
- Height: 7.5mm
- Pin spacing: 6.5mm
- Impedance: 16 Ohm
- Working frequency: 2 to 5 KHz
- Quantity: 1 unit

NFC module for Educational STEAM Kit.  Near field communication (NFC) is a set of standards for smartphones and similar devices to establish radio communication with each other by touching them together or bringing them into close proximity, usually no more than a few centimeters. Compatible with almost any microcontroller, Arduino, PIC, AVR. It can be used in Access Control projects and Alarm projects. RFID PN532 NFC Module features:
- Based on the NXP PN532 chip, it can be used for non-contact communication of 13.56M.
- Greater effective communication distance of 3 cm.

ESP32 processor development board with WiFi and Bluetooth (BLE) compatible with Arduino Uno shields. It is much faster than the ESP8266 processor (NodeMCU and the like) . Wemos D1 ESP32 R32 WROOM-32 WiFi and Bluetooth features:
Power: 5-12VDC WiFi 802.11 b / g / n / e / i (802.11n up to 150 Mbps) Bluetooth v4.2 BR / EDR and BLE. Compatible with Arduino Uno shields. 6 Analog input. 20 digital inputs / outputs (3.3V) (with PWM functions, interrupt). UART, SPI, I2C communication. Size: 68Ã — 53 mm Micro USB connection. 4Mbytes Flash Memory 520Kb Clock: 240Mhz (a core dedicated to WiFi processing) Temperature: -40C + 85C Current: 250mA (max) Current in saving mode: 0.15mA Operating current: 20mA (without WiFi) Useful links for Arduino / Raspberry programming and projects with Arduino /

HD V2 Raspberry Pi camera board The Raspberry Pi High Definition (HD) camera board connects to any Raspberry Pi or Compute Module to create HD photos and video.
Uses Sony's IMX219PQ image sensor that offers high-speed, high-speed video images Sensitivity.
Raspberry Pi Camera Module offers reduced image contamination such as fixed pattern noise and smudges. It also has automatic control functions such as exposure control, white balance and luminance detection.
Raspberry Pi Camera Board, Sony IMX219 8 Megapixel Sensor features:
High-quality images
High data capacity
Fixed 8 megapixel focus (includes focus adjustment tool)
Compatible with 1080p, 720p60 and VGA90
Sony IMX219PQ CMOS image sensor
15-pin ribbon cable

Raspberry Pi HD Pi NoIR V2 camera board Raspberry Pi HD Pi NoIR camera board connects to any Raspberry Pi or Compute Module to create HD photos and video. The Pi NoIR (without infrared) is the same as the standard camera module but without an infrared filter. Therefore, it is excellent for photography and video in the dark.
The module uses Sony's IMX219PQ image sensor that offers high-speed, high-sensitivity video images.
The Pi NoIR module offers contamination from Reduced image such as fixed pattern noise and smudges. It also has automatic control functions such as exposure control, white balance and luminance detection. Raspberry Pi NoIR Camera Board, Sony IMX219 8 Megapixel Sensor features:
and benefits: No infrared filter
High quality images

A Mini WIFI board ESP8266 contains 16MB flash, external antenna connector and built-in ceramic antenna based on ESP-8266EX. Wemos D1 Mini Pro-16 Module + Esp8266 Wifi Series Wireless Antenna features:
- Compatible with Arduino, programming with the Arduino IDE, MicroPython, NodeMCU
- Supply voltage: 5V
- Logical levels: 3.3V - 16MB (128Mbit) flash
- 11 pins of input / output - I2C / one-wire interface, LOLIN I2C port
- 1 ADC (input: 0-3.2V) - built-in ceramic antenna - external antenna connector - Power switch - Includes external WIFI antenna with IPEX SMA adapter Wemos D1 Mini Pro-16 Module + Esp8266 Wifi Series Wireless Antenna features:
of esp8266:
- Supported protocols: 802.11 b / g / n
- Network support: 2 , 4 GHz

Audio amplifier for dual-channel loudspeakers. Supply voltage: 12-24 V. Maximum power: 2x50W. Power consumption: 3-5A.

Amplifier for speakers, especially for cars, dual channel and with subwoofer. It operates at 12/24V and offers an output power of 50W for each channel + 100W subwoofer. Create your 2.1 speaker system with this amplifier.

The module with high quality mobile phone vibration motor, the vibration effect is obvious and the vibration intensity of the motor can be controlled by PWM.

It can be used for Arduino and Raspberry projects. It is a DC motor.

The amplifier with high efficiency, in case of 12 V power supply can output 10 W + 10 W power.

The Raspberry Pi High Definition (HD) camera board connects to any Raspberry Pi or Compute Module to create HD photos and video.

The ESP32-CAM is a camera module with the ESP32-S chip. It features an OV2640 camera, several GPIOs to connect peripherals, and microSD card slot.

This cable is an essential element of the Qwiic ecosystem - it enables connection between the protoboard and any device with a Qwiic connector. With all the benefits of Qwiic at hand - no soldering required, easy 1-second hookup on click and dismantling. The cable is 150mm long. Wires are color coded according to scheme:

It is a basic cable for connection of Qwiic elements featuresd with two JST 1mm connectors. The Qwiic cables are color coded and the connector is polarized making it easy and quick to connect the components. The cable is 50mm long

It is a basic cable for connection of Qwiic elements featuresd with two JST 1mm connectors. The Qwiic cables are color coded and the connector is polarized making it easy and quick to connect the components. The cable is 100mm long

This small GPS breakout is yet another Qwiic module from SparkFun as per usual based on I2C - meaning that you can keep your serial port free for other applications. The board features XA1110 GPS module from GTOP and MediaTek MT3333 chipset already loaded with SparkFun firmware enabling clean and easy use of both ports. 

It is the freshest serial LCD from SparkFun. Similarly to other SparkFun LCD screens it is put on single board with a microcontroller, however in contrast to the other screens in our offer (SP027 and SP028) it is based on PIC16F88 rather than ATmega328.

This little board is great for any type of prototyping - enables troubleshooting and debugging of any board with voltage from 0 to 5.5V. The  board interprets the commands and sends them further via a proper protocol (ranging from UART through I2C up to HDD44780 LCD). The Pirate lets analyze as well the data sent back from the device to the computer terminal effectively allowing to decipher potential errors. The bootloader installed on the board enables the quick and easy update of firmware and changing the functionality of the board.

This board features PIC24FJ64 and FT232RL USB-to-serial chip enabling swift communication over the mini-B USB port. On the other end of the board 2x5 pin header is placed with detailed descriptions of each pin.

SparkFun XBee Explorer Dongle enables the communication between your computer and any XBee device, as in case of any XBee device, without any cables!

The module is compatible with Series 1, Series 2.5 and standard Pro version with voltage regulator functioning with the current up to 500 mA.

SparkFun XBee Explorer Dongle enables the communication between your computer and any XBee device, as in case of any XBee device, without any cables!

The module is compatible with Series 1, Series 2.5 and standard Pro version with voltage regulator functioning with the current up to 500 mA.

Bone Conduction Transducer + MAX98306 Stereo Amplifier features:
- Transducer Bone conduction 8Ohm Speaker 1W + MAX98306 Stereo Amplifier
- Class D 3.7W stereo audio amplifier - MAX98306

NodeMcu module based on ESP8266 controller and programming in Lua language. 
NodeMcu is equipped with 10 GPIO, PWM, I2C, 1-wire and ADC. ESP8266-12E is an improved version of ESP8266-12. 
It works as a standard WiFi 802.11 b / g / n 2.4 GHz. 
USB communication - the CP2102 chip. Characteristic of ESP 12E: 
- Supply voltage: 3.3V (LOGICAL LEVELS: 3.3V), 
- Supported protocols: 802.11 b / g / n, 
- Network support: 2.4 GHz, 
- Band: 2400 (MHz), 
- Wi-Fi Direct (P2p), Soft Access Point, 
- TCP Stack / Integrated IP, 
- PLLs, Regulators and Integrated Power Management Units, 
- Output Power: 0.15 (W); + 19.5dBm in 802.11b mode,

The SIM800A modem is based on SIMCOM's dual band GSM / GPRS.

5V USB powered water pump. Submersible pump for aquariums. It doesn't make a lot of noise while you're working.

5V water pump with USB connector  for fountain, aquarium, pool, water tank, humidifier, green wall decoration, candle

decoration, solar water circulation,etc.

Impressive, professional, high-definition camera module. Official product of Raspberry Pi.

The official Raspberry Pi HQ Camera includes a 1/3" (8.5mm) Sony IMX477 sensor with 12.3MPx resolution and up to 50% increased sensitivity of pixels per area, offering greater sensitivity to light.

It is specially designed to work with CS or C-mount interchangeable lenses (CS-C adapter included). It allows you to use both fixed and varifocal lenses, and you can also use other lenses such as M12 lenses by using an M12 to CS mount converter.

The ADS1115 is an external 16-bit ADC + a built-in programmable gain amplifier (or PGA), which can be very useful for certain Arduino and ESP8266 projects. This is ideal when more resolution or more analogue pins are required. You get better accuracy, as well as relieving the processor of this burden.

This LED power amplifier with a Sonoff power adapter is designed to extend existing Sonoff LED lighting systems. With this signal amplifier, you have the option to extend your Sonoff LED strip system, as the included power adapter provides sufficient power.

This E27 bulb adapter will allow you to control its on and off by WiFi and to control your lamps by the free eWeLink APP, with which you can create routines and scenes, by IFTTT, or also by voice assistants such as Alexa or Google Home.

5 meter LED strip easily installed for use with Sonoff controllers via WiFi and RF. Great lights to create any ambience in any room. Change their colour and rhythm from your mobile or controller. Dance to the rhythm of the lights, copy the colour from your mobile or control the lighting with your voice assistant like Alexa or Google Home. Decorate your home with an infinite number of possible scenes. (Controller and adapter not included)

This 1-meter probe uses the original DS18B20 temperature sensor chip. The DS18B20 is a waterproof temperature sensor/thermometer. It is waterproof, moisture proof and rustproof with the high quality stainless steel tube encapsulated. This is a spare part or accessory used in SONOFF TH10 / TH16.

WROOM-32 DEVKIT V1 is an ESP32 processor development board with WiFi and Bluetooth (BLE). It is much faster than the ESP8266 processor (NodeMCU and similar), and very easy to use, with 2x15 pins.

The Ethernet module for Arduino and compatible boards based on the Wiznet W5500 chip, faster than the previous W5100. It provides an easy way to connect your module to the local network and internet based WIZNET with a TCP/IP interface. Compatible with libraries with the same Ethernet API. A web server can be built with this module. It can be used as a server or as a client.

The Ethernet module for Arduino and compatible boards based on the Wiznet W5500 chip, faster than the previous W5100. It provides an easy way to connect your module to the local network and internet based WIZNET with a TCP/IP interface. Compatible with libraries with the same Ethernet API. A web server can be built with this UNO board shield. It can be used as a server or as a client.

The WIZ850io is a compact sized network module (Ethernet module) for Arduino and compatible boards based on the Wiznet W5500 chip, faster than the previous W5100. It provides an easy way to connect your module to the WIZNET Ethernet-based local network and internet with a TCP/IP interface. Compatible with libraries with the same Ethernet API. With this module with RJ-45 port you can build a web server. It can be used as a server or as a client.

TE Connectivity's Micro K series automotive PCB relays are through-hole mounted relays.  Typical applications include: locking control circuits, seat adjustment motors, window defrosters, starter solenoid switches, in car alarms, door monitoring and closing, hazard warning signs, heated front/rear displays, immobilizers, front/rear/fog lights, interior lights, sunroofs, turn signals, window lifters and wiper control.

- Supply voltage: 12V

- Output current: 30A

- Contact configuration: SPDT

Small peristaltic pump is a type of hydraulic positive displacement pump used for pumping a variety of fluids.

Buzzer alarm to convert electrical signals into intermittent acoustic signals in robotic devices and Arduino projects

A buzzer with a pulsating tone generator, after connecting the supply voltage (DC) in the range of 3V -24V, the buzzer generates an intermittent signal with a frequency of approximately 1 Hz. Application example: as a reverse alarm system for a car. 

Elegant WIFI controlled touch wall light switch with 3 switches. SONOFF TX offers you perfect intelligence control solutions for your home or workplace. Compatible with Amazon Alexa, Google Assistant DIY Smart Home, Nest via iPhone or Android.

Red, yellow and green LED traffic light mini kit ideal for educational and beginner Arduino projects.

A waterproof pentaband antenna X000016  for all your wireless projects with Arduino and development boards

16mm fixed lens compatible with Raspberry Pi official HQ Camera (Reference RA094) C-mount, long distance telephoto type (up to 40m) 10 Mpx.

This small GPS module is an ideal module for Arduino. The NEO-7 series is characterised by the exceptional performance of the highly sensitive u-blox 7 GNSS (GPS, GLONASS, QZSS and SBAS).

Grove module with a red LED light. Ideal for quick and easy connections thanks to the Seeed Grove connector.

USB adapter that allows a direct USB connection to your ESP8266 ESP-01 or ESP-01S WiFi module. Based on the CH340 integrated circuit, which is a USB - Serial converter (UART).

SONOFF DUALR3 is a WiFi based 2-gang switch that can independently connect and control two connected devices or lights - this simply means that 1 SONOFF DUALR3 control switch is equivalent to 2 Sonoff basic switches!

ESP32-S3-DevKitC-1-N8 general-purpose development board based on the ESP32-S3-WROOM-1 chip.

An extremely accurate I2C real time clock (RTC) (DFR0469) with crystal compensation and internal rechargeable battery.

TinyS3 is the latest in Unexpected Maker's popular range of "Tiny" development boards. It's packed with amazing features and peripherals, wireless connectivity, and stacks of Flash and PSRAM, all in the same tiny package size as the original TinyPICO!

2 meter LED strip easily installed for use with Sonoff controllers via WiFi and RF. Great lights to create any ambience in any room. Change their colour and rhythm from your mobile or controller. Dance to the rhythm of the lights, copy the colour from your mobile or control the lighting with your voice assistant like Alexa or Google Home. Decorate your home with an infinite number of possible scenes. (Controller and adapter not included)

SONOFF AL010 RJ9 Adapter dedicated to sensors compatible with the previous Sonoff TH16 series, where there was a Mini Jack connector.

Suitable for temperature and humidity sensor AM2301 and Si7021, waterproof temperature sensor DS18B20 and soil moisture sensor MS01.

TUYA IoT interface module - you will be able to control your projects IoT Internet of Things interface of your Arduino. Tuya interface that allows you to control outputs of the Arduino module via WiFi network using apps for Android and iOS mobile devices. The device communicates with Arduino via UART interface, powered by 5V.

NSPanel offers intelligent control of home appliances: lighting, thermostat, curtains, windows and wall switches. A colour touch screen with two buttons displays all the necessary information and allows you to conveniently navigate through the device's menu, making the Sonoff NSPanel the ideal control centre for your home. The NSPanel is designed to be mounted on the Sonoff switch frame (switch frame not included).

APC220 433 MHz long range wireless modules with USB programming interface. The set provides wireless communication with a range of up to 1000 metres. Easy to configure solution for remote control of e.g. a robot.

The SparkFun Qwiic Cable Kit includes 10 cables of different lengths and styles that will connect your Qwiic boards to each other, to a development platform or to a breadboard. Each Qwiic cable is colour coded red, black, blue and yellow with 1mm JST termination.

SparkFun DataLogger IoT - 9DoF is a pre-programmed data logger to automatically log IMU, GPS and various pressure, humidity and distance sensors - all without having to write a single line of code! DataLogger automatically detects, configures and logs Qwiic sensors. It is specifically designed for users who only need to capture a large amount of data in a CSV or JSON file and return it to their larger project.

M12 high resolution lens, 16MP, 105° FOV, 3.56mm focal length, Raspberry Pi HQ camera M12 compatible.