Fotoboard Pre-Sensitized Photoresist Coated PCB Copper Laminate - One-Sided 10x15cm Fotoboard Pre-Sensitized Photoresist Coated PCB Copper Laminate - One-Sided 10x15cm features:- One side plate for prototype 100x150mm 35um- Fiberglass Code H0164 Available Regular price €3.76 -€0.56 Price €3.20
Bluetooth Transceiver Module HC-06 Wireless HC-06 Bluetooth transceiver module with base.The bluetooth module HC-06 is one of the best options for projects, in which you need wireless communications.The transceiver module allows bluetooth wireless connections as a slave, ready to listen for connection requests. Bluetooth Transceiver Module HC-06 Wireless features: - Chipset CSR BC417- 3.5V - 5V power- Bluetooth version V2.0 + EDR- Frequency: 2.4GHz ISM band- Modulation: GFSK- Reach approx. 10m- Security: Authentication and encryption.- Speed-> Asynchronous: 2.1Mbps (Max) / 160 kbps; Synchronous: 1Mbps / 1Mbps- Supports AT commands for configuration through a serial port- Working temperature: -20ºC to + 75ºC- Working current - pairing: 80 mA Code W0009 Available Price €4.45
Electric precision drill & gringer 12V Electric precision drill & gringer 12V features: - electric drill: 12000 rpm, with on/off switch - grinder stone: 2 pcs - engraving bit: 2 pcs - collet: 2 pcs - direct driven Specifications power: - 4 W (no load) / 16 W (load) / max. 20 W - speed: 12000 rpm - power supply: 12 VDC 0.4 A (not incl.) - drilling Ø: 1 mm Code H0157 ✗ Out-of-Stock Price €11.56
Resistor 5,6K Ohm 5% 0,25W 1/4W Resistor 5,6K Ohm 5% 0,25W 1/4W features:-5.6K Ohm-Type: Carbon film-Tolerance: ±5%-Power: 0.25W-Dimensions: 2x7mm Code D0019 Available Price €0.07
Wireless Module AT-09 Bluetooth 4.0 CC2541 IOS BLE - Bluetooth 4.0 AT-09 BLE Master / Slave module with 6-pin connection base - This module is very similar to HM-10 module - Bluetooth protocol: Bluetooth V4.0 BLE specification - Ultra-low power consumption, in 90uA standby mode Wireless Module AT-09 Bluetooth 4.0 CC2541 IOS BLE features: - Chipset based on CC2541 - Bluetooth Class 2 - Industrial level Bluetooth module SPP - Flash 256Kb - Integrated chip antenna - Power supply: + 3.3 VDC 50 mA - Working temperature: -5 C to + 60 C - Operating frequency: 2.4 GHz ISM Band - Modulation method: GFSK (Gaussian Frequency Shift keying) Code W0078 Available Price €4.09
TDA2822M Dual DIP8 Stereo Audio Low Voltage Power Amplifier TDA2822M Dual DIP8 Stereo Audio Low Voltage Power Amplifier features:- Package / Case: 8-DIP- Voltage - Supply (Vs): 1.8V ~ 15V- Quantity: 1 unit Code T0018 Available Price €1.23
Micro SD Card Reader/Recorder The micro SD card reader module is a simple solution for transferring data to and from a standard micro SD card.The pinout is directly compatible with Arduino, but it can also be used with other microcontrollers.Ideal for projects with ARDUINO, PIC, AVR, STM32.Micro SD Card Reader/Recorder features:- Supply voltage: 4.5V- 5.5V- Adjustable 3.3V built-in regulator for SPI pins- Consumption <200mA- Interface: SPI- Dimensions: 24mmx 42mm x 12mmSupports microSD cards (up to 2G) and micro SDHC (up to 32G) Code M0006 Available Price €2.06
Matrix Membrane Keyboard 4x4 Modulo High-quality membrane keyboard, with 16-key matrix, ultra-thin, less than 1mm thick, with adhesive system on the reverse side. Ideal for your Arduino projects, but can also be used with other microcontrollers. Matrix Membrane Keyboard 4x4 Modulo features: - Rating circuit, Max: DC 35V 100 mA - Cable length: 85 mm - Dupont 8 pin connector - Specific insulation: 100 M Ohm, 100V - Useful life: + 1 million uses - Contact parting: Code M0025 Available Price €1.48
DS1307 AT24C32 RTC real time module Can be used in projects of Arduino, PIC, AVR, STM32 and other. DS1307 AT24C32 RTC real time module features: - Based on DS1307Z- EEPROM memory 24C32 (4Kx8) available for the user- I2C interface- Hour, minutes, seconds, day, month, date, year- AM / PM time- Compensation of leap years- Quartz 32.768kHz- Dimensions: 28x26x8mm- Includes CR2032 3V battery Code M0101 Available Price €1.48
NRF24L01 Adapter + Socket Wireless Transceiver 2.4GHz NRF24L01 Adapter + Socket Wireless Transceiver 2.4GHz features: - The NRF24L01 + module is powered with 3.3V- This adapter module includes a 3.3V voltage regulator- You can connect the NRF24L01 module on it at 5V voltage- Dimensions of PCB: 25x 18mm- Quantity: Adapter 1 unit Code W0023 Available Price €1.23
Lilypad LED Blue Blue LED.The color option allows you to adjust the LEDs to your liking to sew clothes or anything else you can dream of.Lilypad is a wearable E-textile technology developed to have large connection pads to attach to clothing. Lilypad LED Blue features: - Operating voltage: 3 - 5 VDC- Very bright- Density of the PCB: 0.8 mm- LED color: blue- Size: 5.5x12.5 mm- 1 LED included Code M0137 Available Regular price €0.82 -€0.20 Price €0.62
VGA camera 640x480 OV7670 B 0.3MPx 30fps Cmos Camera module for Arduino, Raspberry Pi 2 and Pi 3, B and B +. VGA camera 640x480 OV7670 B 0.3MPx 30fps Cmos features: > - Input voltage 2.5V-3V - Operating power 60mW / 15fps VGA YUV - Resolution VGA 640x480 pixels (30fps) - Maximum frame rate 30fps VGA - Flicker 50Hz / 60Hz automatic detection - Lens size 1/6 " - Angle of view 25 ° - Sensitivity 1.3V / (lux- seg) - SCCB (Serial Camera Control Bus) interface - Output format · 8 Bits - YUV / YCbCr 4: 2: 2 - RGB 565/555/444 - GRB 4: 2: 2 - RAW RGB data - High sensitivity Light operation - Automatic adjustment - Color level saturation - Edge enhancement - Noise level Code M0103 Available Regular price €4.79 -€1.00 Price €3.79
M12 High Resolution Lens, 14MP, 184.6° FOV, 2.72mm Focal length, Compatible with Raspberry Pi High Quality Camera M12 M12 High Resolution Lens, 14MP, 184.6° Ultra wide angle, 2.72mm Focal length, Compatible with Raspberry Pi High Quality Camera M12. Code WV010 Available Price €18.97
Sonoff Slampher - WiFi and RF 433MHz Intelligent Light Support Adapter This E27 bulb adapter will allow you to control its on and off by WiFi and to control your lamps by the free eWeLink APP, with which you can create routines and scenes, by IFTTT, or also by voice assistants such as Alexa or Google Home. Code WS015 ✗ Out-of-Stock Price €14.87
SD Card Module Reader The SD card reader module is a simple solution for transferring data to and from a standard SD card.The pinout is directly compatible with Arduino, but it can also be used with other microcontrollers.SD Card Module Reader features:- Supply voltage: 3.3V or 5V - Interface: SPI 3.3V- Dimensions: 30mm x 50mm x 12mm Code M0023 Available Price €0.82
ENC28J60 Ethernet LAN Network Module Mini AVR LPC STM3 The network module communicates with the Arduino type board through the SPI protocol ideal for projects with ARDUINO, PIC, AVR, STM32. ENC28J60 Ethernet LAN Network Module Mini AVR LPC STM3 features: - Chip ENC28J60 Microchip- Module: 10Base-T- 3.3V power- SPI interface- 25Mhz speed- LED status LED- Hanrun network transformer- Network Interface board HR911105A- Operating temperature: -40ºC to + 85ºC- Dimensions: 51 x 19 x 16 mm Code W0006 Available Price €8.18
4-Channel 5V 10A Relay Module Characteristic: - Channels: 4 (independent protected by Optocouplers) - Supply Voltage: 5V - Output Current: 10A - Relay activation current: 15mA ~ 20mA - Isolation: Yes - Indicator LED: For each channel - Dimensions: 54x 72mm - 5V Optocoupled 4-Channel Relay Module - This module can be directly controlled by the microcontroller (Arduino, 8051, AVR, PIC, DSP, ARM, ARM, MSP430, TTL) Useful links for Arduino / Raspberry programming and projects with Arduino / Raspberry boards: User manual for the remote control + 4-channel 315 MHz IC2262 receiver: - Relay Module Programming 5V 10A 4 Channel with remote control + 4 channel receiver Code RL007 Available Price €3.30
Qwiic cable kit The SparkFun Qwiic Cable Kit includes 10 cables of different lengths and styles that will connect your Qwiic boards to each other, to a development platform or to a breadboard. Each Qwiic cable is colour coded red, black, blue and yellow with 1mm JST termination. Code SP098 Available Price €9.88
DS1307 AT24C32 RTC real time module Can be used in projects of Arduino, PIC, AVR, STM32 and other. DS1307 AT24C32 RTC real time module features: - Based on DS1307Z- EEPROM memory 24C32 (4Kx8) available for the user- I2C interface- Hour, minutes, seconds, day, month, date, year- AM / PM time- Compensation of leap years- Quartz 32.768kHz- Dimensions: 28x26x8mm- Includes CR2032 3V battery Code M0101 Available Price €1.48
NRF24L01 Adapter + Socket Wireless Transceiver 2.4GHz NRF24L01 Adapter + Socket Wireless Transceiver 2.4GHz features: - The NRF24L01 + module is powered with 3.3V- This adapter module includes a 3.3V voltage regulator- You can connect the NRF24L01 module on it at 5V voltage- Dimensions of PCB: 25x 18mm- Quantity: Adapter 1 unit Code W0023 Available Price €1.23
Lilypad LED Blue Blue LED.The color option allows you to adjust the LEDs to your liking to sew clothes or anything else you can dream of.Lilypad is a wearable E-textile technology developed to have large connection pads to attach to clothing. Lilypad LED Blue features: - Operating voltage: 3 - 5 VDC- Very bright- Density of the PCB: 0.8 mm- LED color: blue- Size: 5.5x12.5 mm- 1 LED included Code M0137 Available Regular price €0.82 -€0.20 Price €0.62
VGA camera 640x480 OV7670 B 0.3MPx 30fps Cmos Camera module for Arduino, Raspberry Pi 2 and Pi 3, B and B +. VGA camera 640x480 OV7670 B 0.3MPx 30fps Cmos features: > - Input voltage 2.5V-3V - Operating power 60mW / 15fps VGA YUV - Resolution VGA 640x480 pixels (30fps) - Maximum frame rate 30fps VGA - Flicker 50Hz / 60Hz automatic detection - Lens size 1/6 " - Angle of view 25 ° - Sensitivity 1.3V / (lux- seg) - SCCB (Serial Camera Control Bus) interface - Output format · 8 Bits - YUV / YCbCr 4: 2: 2 - RGB 565/555/444 - GRB 4: 2: 2 - RAW RGB data - High sensitivity Light operation - Automatic adjustment - Color level saturation - Edge enhancement - Noise level Code M0103 Available Regular price €4.79 -€1.00 Price €3.79
M12 High Resolution Lens, 14MP, 184.6° FOV, 2.72mm Focal length, Compatible with Raspberry Pi High Quality Camera M12 M12 High Resolution Lens, 14MP, 184.6° Ultra wide angle, 2.72mm Focal length, Compatible with Raspberry Pi High Quality Camera M12. Code WV010 Available Price €18.97
Sonoff Slampher - WiFi and RF 433MHz Intelligent Light Support Adapter This E27 bulb adapter will allow you to control its on and off by WiFi and to control your lamps by the free eWeLink APP, with which you can create routines and scenes, by IFTTT, or also by voice assistants such as Alexa or Google Home. Code WS015 ✗ Out-of-Stock Price €14.87
SD Card Module Reader The SD card reader module is a simple solution for transferring data to and from a standard SD card.The pinout is directly compatible with Arduino, but it can also be used with other microcontrollers.SD Card Module Reader features:- Supply voltage: 3.3V or 5V - Interface: SPI 3.3V- Dimensions: 30mm x 50mm x 12mm Code M0023 Available Price €0.82
ENC28J60 Ethernet LAN Network Module Mini AVR LPC STM3 The network module communicates with the Arduino type board through the SPI protocol ideal for projects with ARDUINO, PIC, AVR, STM32. ENC28J60 Ethernet LAN Network Module Mini AVR LPC STM3 features: - Chip ENC28J60 Microchip- Module: 10Base-T- 3.3V power- SPI interface- 25Mhz speed- LED status LED- Hanrun network transformer- Network Interface board HR911105A- Operating temperature: -40ºC to + 85ºC- Dimensions: 51 x 19 x 16 mm Code W0006 Available Price €8.18
4-Channel 5V 10A Relay Module Characteristic: - Channels: 4 (independent protected by Optocouplers) - Supply Voltage: 5V - Output Current: 10A - Relay activation current: 15mA ~ 20mA - Isolation: Yes - Indicator LED: For each channel - Dimensions: 54x 72mm - 5V Optocoupled 4-Channel Relay Module - This module can be directly controlled by the microcontroller (Arduino, 8051, AVR, PIC, DSP, ARM, ARM, MSP430, TTL) Useful links for Arduino / Raspberry programming and projects with Arduino / Raspberry boards: User manual for the remote control + 4-channel 315 MHz IC2262 receiver: - Relay Module Programming 5V 10A 4 Channel with remote control + 4 channel receiver Code RL007 Available Price €3.30
Qwiic cable kit The SparkFun Qwiic Cable Kit includes 10 cables of different lengths and styles that will connect your Qwiic boards to each other, to a development platform or to a breadboard. Each Qwiic cable is colour coded red, black, blue and yellow with 1mm JST termination. Code SP098 Available Price €9.88