DC voltage sensor 0-25v for Arduino

It is a basic cable for connection of Qwiic elements featuresd with two JST 1mm connectors. The Qwiic cables are color coded and the connector is polarized making it easy and quick to connect the components. The cable is 100mm long

1 Channel Relay Module DC 5V 10A Low/High Trigger for Arduino features:
- Channel: 1 (protected with Optocoupler)
- Supply voltage: 5V
- Output Current: 10A
- Relay activation current: 15mA ~ 20mA
- Insulation: Yes
- Trigger signal type jumper (low / high)
- LED indicator
- Dimensions: 30x 54mm
- Has a jumper that allows to choose type of trigger signal (low / high)
- This module can be controlled directly by the microcontroller (Arduino, 8051, AVR, PIC, DSP, ARM, ARM, MSP430, TTL)

This module is a three-way switch (COM, NO and NC) that uses the intensity of the ambient light to directly control the output load. Its adjustment potentiometer allows you to change the sensitivity and set the threshold for starting the relay. The relay is energized when it is darker than the threshold.
The optical isolation relay effectively protects the chip and ensures better performance.
This module is used for light detection, brightness detection , control of lamps and automatic equipment. Characteristic: - Channels: 1
- Supply voltage: 12VDC
- Output load capacity: 250V 10A AC / 30V 10A DC
- Relay activation current: & gt; 100mA
- Insulation: Yes
- Indicator LED: Green and Red
- PCB size: 5x2.6 cm / 1.96x1.02 "

Edup Mini Dongle WiFi USB For pcDuino 3 Nano Raspberry Pi features:
- Interface type: USB
- Supports IEEE 802.11e draft 802.11n
- Supports USB 2.0, compatible with USB 1.1 and 1.2
- Support systems:
- Win2k / XP / Vista / Win7 / Win8.1 / Win10 / Mac / Linux
- Operating distance: 91 meters indoors, 275 meters in open space
- Transfer rate: 150Mbps (downlink) and 150Mbps (uplink)
- Works with old Wireless-G and Wireless-B networks
- WEP and WPA encryption - 64-bit / 128-bit WEP (Wired Equivalent Privacy), TKIP, AES 2,400GHz ISM
- Frequency range: 2.4 to 2.4835 GHz
- Operating channels: 13 - Support network protocol: CSMA / CA with acknowledgment
- Transmission mode: DSSS

WT32-SC01 development board with Esp32 from Espressif. 3.5 inch 480 x 320 TFT LCD touch screen, 4MB SPI Flash and 8MB PSRAM.

This cable is an essential element of the Qwiic ecosystem - it enables connection between the protoboard and any device with a Qwiic connector. With all the benefits of Qwiic at hand - no soldering required, easy 1-second hookup on click and dismantling. The cable is 150mm long. Wires are color coded according to scheme:

The 2.5mm female jack connector is a connector to provide power to computers, LED TVs, routers, etc ...
This 2.5mm female jack connector adapter soldered on a PCB board, is ideal for use in our projects.
It has connection points where we can easily solder some pins to connect it directly to a breadboard, or solder a cable over those same connection points.
Adapter 2.5mm female power jack with PCB features:
- Connector type: 2.5mm female jack ,
- Color: black,
- Nominal voltage: 12v DC,
- Maximum current: 0.5A DC,
- Insulation resistance: ‰ ¥ 100MΩ,
- Operating temperature: -25ºC to + 85ºC,
- Number of output pins: 3
- Pitch between output pins: 2.54mm.

 Master Slave Bluetooth Modul for Arduino iOS Android. The HM10 supports Bluetooth 4.0 (low energy) and therefore has a relatively low power consumption.

LED of red color.
The color option allows you to adjust the LEDs to your liking to sew clothes or anything else you can dream of.
Lilypad is a wearable E-textile technology developed to have large connection pads to attach to clothing. Lilypad LED Red features:
- Operating voltage: 3 - 5 VDC
- Very bright
- Density of the PCB: 0.8 mm
- LED color: red
- Size: 5.5x12.5 mm
- 1 LED included