Voice Recording and Reproduction Module ISD1820
  • Voice Recording and Reproduction Module ISD1820
  • Voice Recording and Reproduction Module ISD1820
  • Voice Recording and Reproduction Module ISD1820

Voice Recording and Reproduction Module ISD1820

M0157

This module works under the characteristics of the integrated ISD1820 and allows you to make recordings of multiple messages or the reproduction thereof, it performs a non-volatile storage. Voice Recording and Reproduction Module ISD1820 features:
- Working voltage: 2.4 - 5.5 VDC
- Model: I073103
- Voice Recorder Chip ISD1820
- Automatic ignition mode dwon
cording duration: 8-20 seconds
- Manual or Automatic Control with an MCU
- With internal audio amplifier, this board can drive 8 ohm 0.5W speaker directly
- Includes a microphone on board to record directly
- The sampling frequency and duration can be different if a single module resistance is changed
- High quality, restored natural voice, can be used as a speaker module

OEM
Add to wish list

Voice Recording and Reproduction Module ISD1820 description


This module works under the characteristics of the integrated ISD1820 and allows you to make recordings of multiple messages or the reproduction thereof, it performs a non-volatile storage.

Voice Recording and Reproduction Module ISD1820 features:


- Working voltage: 2.4 - 5.5 VDC
- Model: I073103
- Voice Recorder Chip ISD1820
- Automatic ignition mode dwon
- Recording duration: 8-20 seconds
- Manual or Automatic Control with an MCU
- With internal audio amplifier, this board can drive 8 ohm 0.5W speaker directly
- Includes a microphone on board to record directly
- The sampling frequency and duration can be different if a single module resistance is changed
- High quality, restored natural voice, can be used as a speaker module
- Reproduction loop
- All main pins carry an output connection, allows to operate with microcontroller
- Color blue
- Size: 37x54 mm

Pinout

 

 

 

NumberDescriptions
1 PLAYE - Playback, Edge-activated:When a HIGH-going transition is detected on continues until an End-of-Message (EOM) marker is encountered or the end of the memory space is reached. Upon completion of the playback cycle, the device automatically power down into standby mode Take PLAY LOW during a playback cycle will not terminate the current cycle. This pin has an internal pull-down device. Holding this pin HIGH will increase standby current consumption.
2 REC - The REC input is an active-HIGH record signal.The device records whenever REC is HIGH. This pin must remain HIGH for the duration of the recording. REC takes precedence over either playback(PLAYL or PLAYE) signal. If REC is pulled HIGH during a playback cycle, the playback immediately ceases and recording begins. A record cycles is completed when REC is pulled LOW. An End-of-Message(EOM) marker is internally recorded, enabling a subsequent playback cycle to terminate appropriately. The device automatically power down to standby mode when REC goes LOW. This pin has an internal pull-down device. Holding this pin HIGH will increase standby current consumption.
3 Speaker Outputs - The SP+ and SP- pins provide direct drive for loudspeakers with impedances as low as 8Ω. A single output may be used, but for direct-drive loud-speakers, the two opposite-polarity outputs provide an improvement in output power of up to four times over a single-ended connection will require an AC-coupling capacitor between the SP pin and the speaker. The SP+ pin and the SP- pin are internally connected through a 50KΩ resistance.When not in playback mode, they are floating.
4 MIC - Microphone Input, the microphone input transfers its signals to the on-chip preamplifier. An on-chip Automatic Gain Control (AGC) circuit controls the gain of the preamplifier. An external microphone should be AC coupled this pin via a series capacitor. The capacitor value, together with an internal 10KΩ resistance on this pin, determines the low-frequency cutoff for the 1800 passband.
5 REPLAY - loop play the record.
6 FT - Feed Through: This mode allows use of the speaker drivers for external signals. The signal between the MIC and MIC_REF pins will pass through the AGC, the filter and the speaker drivers to the speaker output SP+ and SP-. The input FT controls the feed through mode. TO operate this mode, the control pins REC, PLAYE and PLAYL are held LOW at Vss. The pin FT is held HIGH to Vcc. For normal operation of record, play and power down, the FT pin is held at Vss. The FT pin has a weak pull-down to Vss.
7 ISD1820 - IC chip
8 Lead Out IO - VCC LED NC FT GND / VCC REC PLAYE PLAYL GND
9 P2 - default short connection ROSC to 100kΩ resistance, that's means record duration is 10s
10 PLAYL - Playback, Level-activated, when this input pin level transits for LOW to HIGH, a playback cycle is initiated. Playback continues until PLAY is pulled LOW or an End-of-Message (EOM) marker is detected, or the end of the memory space is reached. The device automatically powers down to standby mode upon completion of the playback cycle. This pin has an internal pull-down device. Holding this pin HIGH will increase standby current consumption.

Customers who bought this product also bought

SD Card Module Reader

The SD card reader module is a simple solution for transferring data to and from a standard SD card.
The pinout is directly compatible with Arduino, but it can also be used with other microcontrollers.
SD Card Module Reader features:
- Supply voltage: 3.3V or 5V 
- Interface: SPI 3.3V
- Dimensions: 30mm x 50mm x 12mm

M0023

Price €0.99

Arduino compatible Attiny85 Digispark board

Digispark is a development board based on the ATTINY85 microcontroller from ATMEL born in a successful campaign on Kickstarter.
Similar to the Arduino line , It is one of the smallest boards on the market.
Programmable directly from USB with the same Arduino tools. It has a built-in Micronucleus bootloader and can be replaced by similar ones such as the Trinket bootloader. Adafruit or others.
You can use many of the same Arduino libraries and you have your own on the digispark wiki. Arduino compatible Attiny85 Digispark board features:
- USB power supply
- External power supply (7v-35v DC 12v maximum recommended)
- 5V DC 500mA regulator on board
- Programmable with the Arduino IDE
- Loaded with Micronucleus bootloader

B0002

Price €4.90

Voltage Regulator LDO 3.3V DC SOT223 SMD LM1117 TS1117BCW-3.3

Manufacturer: Taiwan Semiconductor 5x Voltage Regulator LDO 3.3V DC SOT223 SMD LM1117 TS1117BCW-3.3 features:
- Type Output: fixed
- Voltage Output: 3.3 V
- Output Current: 800mA
- Max input voltage: 12V
- Operating temperature: -20C to + 85ºC
- Encapsulated: SOT223
- Dropout Voltage Vdo: 1.3V (1A)
- Quantity: 5 units

T0001

Price €0.75
€6.95
Save €1.96 €4.99

4,12 tax excl.

Tax included 1
16 items
Regular price €6.95 Price €4.99

Order until 4pm we will send today
30 days return