Vertical Slide Switch 2P2T 50V 0.5A

DC Step Down Converter 3.3V 2A 3.4-6V features:
- Voltage drop module
- Input voltage: 3.4-6V
- Output voltage: 3.3V
- Current output: adjustable, max 2A
- Operating temperature: -40 to + 85 ºC
- Operating frequency: 1.5MHz
- Efficiency conversion: up to 95%
- Short circuit protection: Yes (limited current 8A)
- Protection over temperature: the output switches off automatically
- Size: 12 x 15 mm
- Full charge output ripple: Vpp <50 mV
- Output accuracy: ± 0.1V
- Current IQ without load: 0.2mA
- Stop current (EN) <10uA

Version compatible with Arduino Nano V3.0
It has an ATMega328P chip running at 16Mhz with bootloader loaded factory.
Characteristic:
- Microcontroller: ATmega328
- Operating Voltage (logic level): 5V
- Input Voltage (recommended): 7-12V
- Digital I / O Pins: 14 (6 PWM outputs)
- Analog Inputs: 8 (A0-A7)
- DC Current per I / O pin 40 mA
- Flash memory: 32 KB (2 KB used by the bootloader)
- SRAM: 2 KB
- EEPROM: 1 KB
- Frequency Clock: 16 MHz
- USB Communication - CH340
- Dimensions: 18 mm x 44 mm

It can be used to work with AVR, ARM, PIC microcontrollers, Arduino modules and to work with self-designed prototypes. Prototype Board Transparent 400 points features:
- Linkable with other plates
- Base with adhesive
- 400 contacts without welding (300 contacts for components and 100 contacts for power rails )
- Transparent ABS
- Measurements 82x 55x 8 mm

Mini protoboard designed to develop simple test projects for the arduino without requiring component soldering.

Mini ESP8266 ESP12E CH340 WiFi Development
NodeMcu module based on ESP8266 controller and programming in Lua language
NodeMcu it is equipped with 10 GPIO, PWM, I2C, 1-wire and ADC
It works as a standard WiFi 802.11 b / g / n 2.4 GHz
Wemos D1 Mini ESP8266 ESP12E CH340 WiFi Wireless Development features:

- Compatible with Arduino, programming with the Arduino IDE
- Power supply voltage: 5V
- LOGICAL LEVELS: 3.3V
- 11 input / output pins
- 1 ADC (input: 0-3.3V)
- Supported protocols: 802.11 b / g / n
- Network support: 2.4 GHz - Band: 2400 (MHz)
- Wi-Fi Direct (P2p), Soft Access Point
- Integrated TCP / IP stack
- PLL, regulators and power management units Integrated

Relay Module DC 5V 10A 2 Channel Low/High Trigger features:
- Channels: 2 (independent protected with Optocouplers)
- Supply voltage: 5V
- Output Current: 10A
- Relay activation current: 15mA ~ 20mA
- Insulation: Yes
- Trigger signal type jumper (low / high)
- LED indicator: For each channel
- Dimensions: 40x 50mm
- It has a jumper that allows to choose type of trigger signal (low / high)
- This module can be controlled directly by the microcontroller (Arduino, 8051, AVR, PIC, DSP, ARM, ARM, MSP430, TTL)

Arduino has decided to further develop its catchy Nano project in the direction of more power. Nano Every is the simplest of the new series as it doesn´t include any sensors nor connectivity solution, however still significantly more powerful than standard Nano (50% more program memory and 2 times more RAM). Above characteristics make it perfect for projects of small devices with more advanced functionalities, such as audio processing or robotics.

Vertical variable PCB resistance from 10KΩ Linear.