5x Hexagonal Separator M3 10mm Male-Female Brass 5x Hexagonal Separator M3 10mm Male-Female Brass features: -Metric thread M3-Male-Female Separator 10mm-Quantity: 5 units Code H0047 Available Price €0.32
Vertical Slide Switch 3P2T 50V 0.5A 6 DIP pins and 2 positions DPDT. This switch is widely used to control the operation of many small electronic power projects, including volume and other controls for audio video, dimmer controls for lights.It is also a great component for DIY. Vertical Slide Switch 3P2T 50V 0.5A features: - Type: 3P2T- Contact resistance: 30 MΩ max.- Insulation resistance: 100 MΩ- Maximum operating voltage: 50V- Maximum operating current: 0.5A- Can support 500 VAC for 1 minute- Step between pins: 2.54mm / 0.1 "- Pin size: 4.5x0.5x15 / 0.77 "x0.19"- Type of current: DC- Pins to be welded- Switch action: 2 ON / OFF positions- Shape of interrupter: rectangular- Size: 16x6.5x15 / 0.2 "x0.02" Code K0188 Available Price €0.40
Resistor 2,2K Ohm 5% 0,25W 1/4W Resistor 2,2K Ohm 5% 0,25W 1/4W features:-2.2K Ohm-Type: Carbon film-Tolerance: ±5%-Power: 0.25W-Dimensions: 2x7mm Code D0015 Available Price €0.07
Digital Touch Sensor B21 The module is based on a touch sensitive IC capacitive touch switch module (TTP223B). In the normal state, the module produces Low power consumption. When a finger touches the corresponding position, the module output is high, if not touched for 12 seconds, it switches to low power mode. Digital Touch Sensor B21 features: - Low power consumption - Input voltage: 2 - 5.5VDC - Can replace the traditional touch of a button - Four M2 screws diameter 2.2 mm that position the holes for easy installation - 3-pin control interface: 1- GND 2- VCC 3- Control signal (output pin) - Power indicators: Bright green LED when the sensor is on Code M0130 Available Price €1.23
Car Robot Tire Wheel Smart Car Car Robot Tire Wheel Smart Car features:- Dimensions of the wheel: - Diameter: 65mm - Width: 26 mm- Quantity: 1 unit Code R0009 Available Regular price €1.57 -€0.41 Price €1.16
NodeMcu V3 Lua ESP8266 ESP12E CH340 WiFi Wireless Module Development Board NodeMcu module based on ESP8266 controller and programming in Lua language. NodeMcu is equipped with 10 GPIO, PWM, I2C, 1-wire and ADC. ESP8266-12E is an improved version of ESP8266-12. It works as a standard WiFi 802.11 b / g / n 2.4 GHz. USB communication - the CH340 chip. Characteristics of ESP 12E: - Supply voltage: 3.3V (LOGICAL LEVELS: 3.3V) - Supported protocols: 802.11 b / g / n - Network support: 2.4 GHz - Band: 2400 (MHz) - Wi-Fi Direct (P2p), Soft Access Point - TCP Stack / Integrated IP - PLLs, Regulators and Integrated Power Management Units - Output Power: 0.15 (W); + 19.5dBm in 802.11b mode Code W0013 ✗ Out-of-Stock Price €3.71
2x PCF8574P I/O Extension Board 8574 NXP - The PCF8574P is an 8-bit remote I / O expander for the I2C bus with 16-pin DIP packet interrupt. - Provides general-purpose remote I / O expansion via a two-wire, two-way I2C bus (Serial Clock (SCL), Serial Data (SDA)). - Devices consist of eight quasi-directional ports , 100KHz I2C bus interface, three hardware address inputs and interrupt output operating between 2.5V and 6V. - Quasi-bidirectional port can be independently assigned as one input to monitor interrupt status or keyboards or as an output to activate indicating devices like LEDs. - System Master can read from the input port or write to the output port through a single register. Code T0010 Available Price €0.95
40x Female-Female Cable 20cm 40x Female-Female Cable 20cm features: -Length: 20cm -Quantity: 40 wires -Dupont female connectors on both ends -Compatible with 2.54mm male connectors -High quality and good working condition -Easy to install and use Code K0004 Available Price €2.06
PAM8610 2X10W Dual Channel Amplifier The amplifier with high efficiency, in case of 12 V power supply can output 10 W + 10 W power. Code M0209 Available Price €2.93
W1209 DC 12V Thermostat + Transparent Box Temperature Controller W1209 DC 12V Thermostat + Transparent Box Temperature Controller features: - Model: W1209 - Supply voltage: DC 12V - Temperature control mode: ON / OFF - Temperature range: -50-110 ° C - Resolution: 0.1 ° C range -9.9 ~ 99.9 ° C, above is 1 ° C - Measure accuracy: 0.1 ° C - Refresh rate: 0.5s - Temperature protection 0-110 ° C - Static current: ‰ ¤ 35mA, working current ‰ ¤ 65mA - Output power: 10A relay - Probe sensor: NTC (10K 0.5%) Waterproof Sensor - Environmental requirements: -10 ~ 60 ° c Humidity 20% -85% - Dimensions: 48 x 40mm Code M0106 Available Regular price €5.32 -€0.07 Price €5.25
Module Relay 5V Light sensor LDR photoresistor This module is a three way switch ( COM, NO and NC ) that uses the intensity of the ambient light to control directly the load at the output. Its adjustment potentiometer allows changing the sensitivity and setting the start threshold of the relay. The relay is energized when it is darker than the threshold. Code RL016 Available Price €1.98
Micro SD Card Reader/Recorder The micro SD card reader module is a simple solution for transferring data to and from a standard micro SD card.The pinout is directly compatible with Arduino, but it can also be used with other microcontrollers.Ideal for projects with ARDUINO, PIC, AVR, STM32.Micro SD Card Reader/Recorder features:- Supply voltage: 4.5V- 5.5V- Adjustable 3.3V built-in regulator for SPI pins- Consumption <200mA- Interface: SPI- Dimensions: 24mmx 42mm x 12mmSupports microSD cards (up to 2G) and micro SDHC (up to 32G) Code M0006 Available Price €2.06
Lilypad Button Board This support is a lilypad button to sew clothing or anything else you can dream of.Lilypad is a wearable E-textile technology developed to have large connection pads to attach to clothing. Lilypad Button Board features: - Density of the PCB: 0.8 mm- Size: 8x16 mm- 1 LED included Code M0142 Available Regular price €0.82 -€0.20 Price €0.62
Sonoff DUALR3 Lite - Wireless Smart Switch SONOFF DUALR3 is a WiFi based 2-gang switch that can independently connect and control two connected devices or lights - this simply means that 1 SONOFF DUALR3 control switch is equivalent to 2 Sonoff basic switches! Code WS046 ✗ Out-of-Stock Price €10.74
16-bit I2C ADS1115 module, 4-channel ADC with professional gain amplifier PGA The ADS1115 is an external 16-bit ADC + a built-in programmable gain amplifier (or PGA), which can be very useful for certain Arduino and ESP8266 projects. This is ideal when more resolution or more analogue pins are required. You get better accuracy, as well as relieving the processor of this burden. Code M0226 Available Price €4.92
TM1637 4-Digit Digital Display Module Module for Arduino, Raspberry Pi 2 and Pi 3, B and B +. The display module 4-digit LED with TM1637. The unit can be controlled with just two DIO and CLK control lines. TM1637 4-Digit Digital Display Module features: - 3V-5V supply voltage - Current consumption 250 mA - 7-segment display 4 digits common anode - Digit size: 0.36 inches - Dimensions: 42x24x11mm Code M0104 Available Price €1.78
Expansion Module I/O XBEE This XBEE module contains everything you need to create your projects, including socket to mount an XBee device, VDC power pins, GND, terminal block to power a servo motor, reset button and much more. The new expansion IO Shield V7.1 offers several advantages and these are its characteristics.Compatible with the new Arduino Due. Code M0150 Available Price €7.02
Capacitive Fingerprint Scanner - UART (AD-013) - OBSOLETE This fingeprint scanner from ADH-Tech combines a highly precise fingerprint sensor module with an onboard MCU and UART interface enabling trivially very connection to any project. The scanner independently reads and analyses the fingerprint thanks to an MCU algorithm that can send a converted digital signal to a peripheral serial interface for a data read. The onboard MCU algorithm enables operations such as for example a fingerprint enroll. Code SP036
PAM8610 2X10W Dual Channel Amplifier The amplifier with high efficiency, in case of 12 V power supply can output 10 W + 10 W power. Code M0209 Available Price €2.93
W1209 DC 12V Thermostat + Transparent Box Temperature Controller W1209 DC 12V Thermostat + Transparent Box Temperature Controller features: - Model: W1209 - Supply voltage: DC 12V - Temperature control mode: ON / OFF - Temperature range: -50-110 ° C - Resolution: 0.1 ° C range -9.9 ~ 99.9 ° C, above is 1 ° C - Measure accuracy: 0.1 ° C - Refresh rate: 0.5s - Temperature protection 0-110 ° C - Static current: ‰ ¤ 35mA, working current ‰ ¤ 65mA - Output power: 10A relay - Probe sensor: NTC (10K 0.5%) Waterproof Sensor - Environmental requirements: -10 ~ 60 ° c Humidity 20% -85% - Dimensions: 48 x 40mm Code M0106 Available Regular price €5.32 -€0.07 Price €5.25
Module Relay 5V Light sensor LDR photoresistor This module is a three way switch ( COM, NO and NC ) that uses the intensity of the ambient light to control directly the load at the output. Its adjustment potentiometer allows changing the sensitivity and setting the start threshold of the relay. The relay is energized when it is darker than the threshold. Code RL016 Available Price €1.98
Micro SD Card Reader/Recorder The micro SD card reader module is a simple solution for transferring data to and from a standard micro SD card.The pinout is directly compatible with Arduino, but it can also be used with other microcontrollers.Ideal for projects with ARDUINO, PIC, AVR, STM32.Micro SD Card Reader/Recorder features:- Supply voltage: 4.5V- 5.5V- Adjustable 3.3V built-in regulator for SPI pins- Consumption <200mA- Interface: SPI- Dimensions: 24mmx 42mm x 12mmSupports microSD cards (up to 2G) and micro SDHC (up to 32G) Code M0006 Available Price €2.06
Lilypad Button Board This support is a lilypad button to sew clothing or anything else you can dream of.Lilypad is a wearable E-textile technology developed to have large connection pads to attach to clothing. Lilypad Button Board features: - Density of the PCB: 0.8 mm- Size: 8x16 mm- 1 LED included Code M0142 Available Regular price €0.82 -€0.20 Price €0.62
Sonoff DUALR3 Lite - Wireless Smart Switch SONOFF DUALR3 is a WiFi based 2-gang switch that can independently connect and control two connected devices or lights - this simply means that 1 SONOFF DUALR3 control switch is equivalent to 2 Sonoff basic switches! Code WS046 ✗ Out-of-Stock Price €10.74
16-bit I2C ADS1115 module, 4-channel ADC with professional gain amplifier PGA The ADS1115 is an external 16-bit ADC + a built-in programmable gain amplifier (or PGA), which can be very useful for certain Arduino and ESP8266 projects. This is ideal when more resolution or more analogue pins are required. You get better accuracy, as well as relieving the processor of this burden. Code M0226 Available Price €4.92
TM1637 4-Digit Digital Display Module Module for Arduino, Raspberry Pi 2 and Pi 3, B and B +. The display module 4-digit LED with TM1637. The unit can be controlled with just two DIO and CLK control lines. TM1637 4-Digit Digital Display Module features: - 3V-5V supply voltage - Current consumption 250 mA - 7-segment display 4 digits common anode - Digit size: 0.36 inches - Dimensions: 42x24x11mm Code M0104 Available Price €1.78
Expansion Module I/O XBEE This XBEE module contains everything you need to create your projects, including socket to mount an XBee device, VDC power pins, GND, terminal block to power a servo motor, reset button and much more. The new expansion IO Shield V7.1 offers several advantages and these are its characteristics.Compatible with the new Arduino Due. Code M0150 Available Price €7.02
Capacitive Fingerprint Scanner - UART (AD-013) - OBSOLETE This fingeprint scanner from ADH-Tech combines a highly precise fingerprint sensor module with an onboard MCU and UART interface enabling trivially very connection to any project. The scanner independently reads and analyses the fingerprint thanks to an MCU algorithm that can send a converted digital signal to a peripheral serial interface for a data read. The onboard MCU algorithm enables operations such as for example a fingerprint enroll. Code SP036