Prototype Breadboard Protoboard 840 points for Arduino

Potentiometer B1K Linear features:
-1k OHM kΩ - linear potentiometer 1k Arduino
-Tolerance: +/- 20%
- Power: 0.125W

Camera module for Arduino, Raspberry Pi 2 and Pi 3, B and B +. VGA camera 640x480 OV7670 B 0.3MPx 30fps Cmos features:
> - Input voltage 2.5V-3V
- Operating power 60mW / 15fps VGA YUV
- Resolution VGA 640x480 pixels (30fps)
- Maximum frame rate 30fps VGA
- Flicker 50Hz / 60Hz automatic detection
- Lens size 1/6 "
- Angle of view 25 °
- Sensitivity 1.3V / (lux- seg)
- SCCB (Serial Camera Control Bus) interface
- Output format · 8 Bits
- YUV / YCbCr 4: 2: 2
- RGB 565/555/444
- GRB 4: 2: 2
- RAW RGB data
- High sensitivity Light operation
- Automatic adjustment
- Color level saturation - Edge enhancement
- Noise level

IIC/I2C adapter PCF8574 LCD 1602 1604 2004 Interface features:
- Based on the PCF8574A chip
- Power: 5V
- Supports I2C Protocol
- A potentiometer for regulate contrast
- Dimensions: 19x42mm PCF8574 - & gt; the default address 0x20
PCF8574A - & gt; the default address 0x3F - You can change anyone between 0x20 and 0x27 depending on whether or not you have soldered pins A0 A1 A2 - With this module the communication between the Arduino and the LCD It is only made through two outputs, SDA and SCL
- Up to 8 LCD screens can be connected to the same I2C bus choosing a different address - Ideal for projects with ARDUINO and Raspberry Pi platforms - You can use it with PIC, AVR, STM32

Version compatible with Arduino Nano V3.0
It has an ATMega328P chip running at 16Mhz with bootloader loaded factory.
Characteristic:
- Microcontroller: ATmega328
- Operating Voltage (logic level): 5V
- Input Voltage (recommended): 7-12V
- Digital I / O Pins: 14 (6 PWM outputs)
- Analog Inputs: 8 (A0-A7)
- DC Current per I / O pin 40 mA
- Flash memory: 32 KB (2 KB used by the bootloader)
- SRAM: 2 KB
- EEPROM: 1 KB
- Frequency Clock: 16 MHz
- USB Communication - CH340
- Dimensions: 18 mm x 44 mm

Digital Voltmeter Red 0-200V DC 0.56 features:
- No battery needed
- Measurement range: 0-200 Vdc
- Supply voltage: 4.5-30 Vdc - Screen: 0.56 € Red Led
- Color: Black
- Includes reverse polarity protection
- Operating current:

Red, yellow and green LED traffic light mini kit ideal for educational and beginner Arduino projects.

This product is a 1 digit screen composed of 7 red LED segments with excellent brightness and features:.
It works with very low current consumption.
The segments of this screen are connected with a common anode point.
LED Display 1-Digit 7-Segment Red Common Anode features:
- Supply voltage of the segments: 3 VDC
- LED color of the segments: red
- Digit length: 14.2mm
- Digit width: 8.1mm
- Pin numbers: 10
- Diameter of pins: 0.51mm
- Step between pins: 2.54mm
- Consumption current per segment: 30mA
- Maximum admissible current per segment: 70mA
- Direct current by segment (pulse operation): 30mA
- Digit numbers: 1
- Segment numbers by digit: 7
- Operating temperature: -25°C - + 85°C

Filament of PLA HD material, perfect for basic and fast projects that do not need excessive durability, for 3D printers. The diameter of the filament is 1.75mm. The package contains 1kg of banana coloured filament