Mobile
NodeMcu module based on ESP8266 controller and programming in Lua language. NodeMcu is equipped with 10 GPIO, PWM, I2C, 1-wire and ADC. ESP8266-12E is an improved version of ESP8266-12. It works as a standard WiFi 802.11 b / g / n 2.4 GHz. USB communication - the CP2102 chip. Characteristic of ESP 12E: - Supply voltage: 3.3V (LOGICAL LEVELS: 3.3V), - Supported protocols: 802.11 b / g / n, - Network support: 2.4 GHz, - Band: 2400 (MHz), - Wi-Fi Direct (P2p), Soft Access Point, - TCP Stack / Integrated IP, - PLLs, Regulators and Integrated Power Management Units, - Output Power: 0.15 (W); + 19.5dBm in 802.11b mode,
NodeMcu module based on ESP8266 controller and programming in Lua language. NodeMcu is equipped with 10 GPIO, PWM, I2C, 1-wire and ADC.
ESP8266-12E is an improved version of ESP8266-12. It works as a standard WiFi 802.11 b / g / n 2.4 GHz. USB communication - the CP2102 chip. p>
Characteristic of ESP 12E: - Supply voltage: 3.3V (LOGICAL LEVELS: 3.3V), - Supported protocols: 802.11 b / g / n, - Network support: 2.4 GHz, - Band: 2400 (MHz), - Wi-Fi Direct (P2p), Soft Access Point, - TCP Stack / Integrated IP, - PLLs, Regulators and Integrated Power Management Units, - Output Power: 0.15 (W); + 19.5dBm in 802.11b mode, - Consumption in low power mode: <10 uA, - Integrated 32-bit processor, - Supports WPA / WPA2, - Supports Lua, AT, - Supports three operating modes: AP, STA, STA + AP, - Communication interface type: SPI, Serial, UART (115200 bps), - Size: 24mm x 16mm.
The distinguishing features: of the ESP-12E module:
- Digital I / O Pins: 11 x GPIO, - ADC input (Analog Digital Converter), - SPI interface.
NodeMcu module based on ESP8266 controller and programming in Lua language NodeMcu is equipped with 10 GPIO, PWM, I2C, 1-wire and ADC ESP8266-12E is an improved version of ESP8266-12 It works as a standard WiFi 802.11 b / g / n 2.4 GHz USB Communication - CP2102 Chip Characteristic: ESP 12E ESP8266 ESP12E NodeMcu Lua Wireless Development Board CP2102 WiFi features: - Supply voltage: 3.3V (LOGICAL LEVELS: 3.3V) - Supported protocols: 802.11 b / g / n - Network support: 2.4 GHz - Band: 2400 (MHz) - Wi-Fi Direct (P2p), Soft Access Point - Integrated TCP / IP stack - PLL, regulators and integrated power management units - Output power: 0 , 15 (W); + 19.5dBm in 802.11b mode
Allows control: - Up to 2 bidirectional current motors- Or 1 stepper motor Shield is compatible with NodeMcu ESP8266 CP2102 WIFI Development Board ESP8266 WiFi Motor Drive L293D Expansion Shield Board ESP12E NodeMcu features: - Minimum operating voltage: 4.5 V- Maximum operating voltage: 36 V- Maximum current: ± 1.2 A- Logic voltage: - 2.3V <= HIV <= VIN (high) - 0.3V <= VIL <= 1.5V (low)- Controller L293D- Measures: 58x42 mm ESP12 port control kit: - D1, D3 - motorA- D2, D4 - motorB
6,98 tax excl.
Available