Development boards

This is a LattePanda (DFR0444) with 2GB RAM and 32GB EMMC memory. The minicomputer is equipped with a 1.92 GHz Intel Cherry Trail Z8350 Quad Core processor. In addition, it has WiFi, Bluetooth 4.0, 2x USB 2.0, 1x USB 3.0, microSD slot, Ethernet port and an additional ATmega32u4 microcontroller with 20 GPIO pins known from Arduino. This version comes with Windows 10 installed, but does not include a Windows 10 activation key.

The SparkFun micro:Climate kit is a complete weather station kit that builds on the weather:bit carrier board with weather and soil moisture sensors, all powered by the micro:bit. board.

FinestraMiner is a highly efficient Helium compatible hotspot that provides wireless network coverage to the Helium network, also called People's Network, the world's largest and fastest growing LoRaWAN network. It allows thousands of IoT devices to connect to this single hotspot using Long-Fi technology, with long-range coverage up to 16 kilometres away.

The Helium network is a decentralised wireless network that allows devices anywhere in the world to connect to the Internet wirelessly.

The accelerometer sensor is an add-on for your RedBot that provides shock and motion detection. The sensor works by measuring acceleration forces on the x, y and z axes. By measuring the amount of acceleration (or lack thereof), your robot can better understand its movements.

Adafruit's Feather meets Raspberry Pi's new RP2040 chip, offering this board with great features. This Feather features the RP2040 and all the niceties you know and love from Feather. It comes fully assembled and tested, with the UF2 USB bootloader. It also comes with a header, so you can solder it and connect it to a solderless test board. 

SparkFun XBee Explorer Dongle enables the communication between your computer and any XBee device, as in case of any XBee device, without any cables!

The module is compatible with Series 1, Series 2.5 and standard Pro version with voltage regulator functioning with the current up to 500 mA.

This BeagleBone® Green Gateway development board is a powerful single board computer (SBC). It is based on Seeed Studio's open source hardware and integrates the functions of Wi-Fi + Bluetooth (BLE) + Ethernet +2 Grove connectors, plus a NEON floating point accelerator and 3D graphics. All in one compact board!

SparkFun XBee Explorer Dongle enables the communication between your computer and any XBee device, as in case of any XBee device, without any cables!

The module is compatible with Series 1, Series 2.5 and standard Pro version with voltage regulator functioning with the current up to 500 mA.

BeagleBone Black Industrial  (102110423)  is designed as a single board industrial computer (SBC). It uses the BeagleBone Black open source hardware design and supports temperatures from -40ºC up to 85ºC.

This small GPS breakout is yet another Qwiic module from SparkFun as per usual based on I2C - meaning that you can keep your serial port free for other applications. The board features XA1110 GPS module from GTOP and MediaTek MT3333 chipset already loaded with SparkFun firmware enabling clean and easy use of both ports. 

Rock Pi 4 model SE 4GB - single board computer with a high-performance hex-core Rockchip RK3399-T processor. It is equipped with 4GB of LPDDR4 RAM, WiFi and Bluetooth 5.0, a Gigabit Ethernet port with PoE, an HDMI port and 2 USB 3.0 and 2 USB 2.0 ports, as well as a 3.5 mm jack plug. The board has 2 x 20-pin GPIO cables and DSI and CSI connectors for display and camera connections. Rock pi 4 SE is the perfect alternative to the Raspberry Pi

This little board is simply a I2C board to Qwiic converter. It pretty much enables any device with I2C connectors to work with Qwiic system. It has two Qwiic ports - both of them served with the same I2C bus. You simply stick the board on your I2C board and get additional two Qwiic ports. It is as easy as it sounds

This Seeeduino XIAO is the smallest Arduino compatible plate of the Seeeduino family. It is an Arduino microcontroller, integrated with the SAMD21 microchip. Despite its tiny size, it has enough interfaces for many applications.

The Qwiic HAT is an absolute basic of Qwiic system for Raspberry. It enables a quick and efficient connection of an sensor to your Raspberry over I2C bus (GND, 3.3 V, SDA and SCL). As Qwiic enables daisy chaining of components, you can pretty much install as many sensors on the Qwiic HAT as you want. On top of that it fits perfectly Pi Tin enclosure from SparkFun enabling connection while in case.

This Seeeduino XIAO is the smallest Arduino compatible plate of the Seeeduino family. It is an Arduino microcontroller, integrated with the SAMD21 microchip. Despite its tiny size, it has enough interfaces for many applications.

This tiny little board features two chips from Maxim Integrated: MAX32664 and MAX30101. The 30101 Oximetry module  is the sensor on board responding for both oximetry and heart rate sesnsing. The MAX32664 is equipped with a Cortex M4 handling algorithimc calculations, digital filtering and automatic gain control. The board comes with I2C and SparkFun has provided to it Qwiic connectors for ease of use.

NVIDIA® Jetson Nano ™ Developer Kit is a small computer with powerful capabilities that allows you to run multiple neural networks in parallel for applications such as image classification, segmentation, speech processing and object detection. All this in an easy-to-use platform that runs on just 5 watts. Thanks to this board, the power of modern Artificial Intelligence is now available to Makers, students and embedded developers everywhere. Discover the power of AI and robotics with the powerful 4GB NVIDIA Jetson Nano Developer Kit. Now educators, students, and any enthusiast can easily perform AI projects quickly and efficiently using their GPU-accelerated NVIDIA software.

This little PCB piece is a great independent display addition to any project. Why independent? Well, it features an ATmega328P AVR on its back, making it a pretty much an UNO with a screen rather than a screen itself.

We have the same screen with a reverse color version, i.e. RGB on black with a reference of SP028

ODYSSEY - X86J4105800 Mini PC Win10 Mas expandible (Linux y Arduino Core) con 8GB RAM. ODYSSEY le permite crear aplicaciones de Edge Computing con una CPU potente e interfaces de comunicación enriquecidas. Basado en Intel Celeron J4105, es una CPU de cuatro núcleos a 1.5GHz que se dispara hasta 2.5GHz. También hay un ATSAMD21 Core integrado, un ARM Cortex-M0 + MCU que le permite programar Arduino en la plataforma x86. Versión no activada sin eMMC. También obtenga el estuche re_computer, que no solo es compatible con ODYSSEY - X86J4105 sino también con todos los SBC populares.

This little PCB piece is a great independent display addition to any project. Why independent? Well, it features an ATmega328P AVR on its back, making it a pretty much an UNO with a screen rather than a screen itself.

We have the same screen with a reverse color version, i.e. black on RGB with a reference of SP028

The re_computer box is specially designed for the re_computer system, but is fully compatible with all popular single board computers (SBC). Its stackable structure allows for endless possibilities, and it also comes with a removable acrylic cover on top.

The design has been prepared and left the screw holes for the installation of the most commercial boards, including the new ODYSSEY - X86J4105, Raspberry Pi, BeagleBone and Jetson Nano.

The Spartan Edge Accelerator Board is an FPGA board developed by Xilinx Spartan in the form of a Shield for the Arduino UNO board. In addition, the integrated ESP32 chip also provides WiFi and Bluetooth functionality.

This FTDI breakout is a super small board with a standard FT232RL USB to serial IC circuit. The pinout fits FTDI cable making it compatible with any Arduino or Arduino compatible 5V boards.

Orange Pi Lite is a super small computer This version includes a camera connector. It uses the Allwinner H3 SoC with Quad-core Cortex-A7, and has 512MB/1GB DDR3 SDRAM. It can run Android 4.4,Ubuntu,Debian image. Orange Pi Lite offers a range of different ports, including HDMI output, 40pin headers,USB 2.0, CSI camera port, TF card slot, etc. It is powered through DC.

This FTDI breakout is a super small board with a standard FT232RL USB to serial IC circuit. The pinout fits FTDI cable making it compatible with any Arduino or Arduino compatible 5V boards.

DIY Mobile Phone Kit - This  stylish little educational device is an open source mobile phone that you can build yourself. It is compatible with all mobile networks, and its purpose is to motivate people to explore, learn and create something new in a fun and interesting way. Age:+11  

Ever needed a microphone for your project. This tiny little board will fulfill all your needs - it is not only mobile, but as well easy to connect. A low power, efficient, omnidirectional AMP401 microphone has an analog output. It works great for near and long range uses and is particularly suitable for a mobile projects given its extremely low energy consumption. You can use it in a range of applications - we can see it used in smartphones, cameras or electronic nannies.

Wio Terminal: ATSAMD51 Core development board with Realtek RTL8720DN BLE 5.0 & Wi-Fi 2.4G / 5G. Arduino and MicroPython compatible, Wio Terminal is an ATSAMD51-based microcontroller with wireless connectivity compatible with Realtek RTL8720DN. Its CPU speed runs at 120MHz (Boost up to 200MHz). The Realtek RTL8720DN chip supports Bluetooth and Wi-Fi, providing the backbone for IoT projects. The Wio terminal itself is equipped with a 2.4 ”LCD screen, integrated IMU (LIS3DHTR), microphone, buzzer, microSD card slot, light sensor and infrared emitter (IR 940 nm).

The SparkFun ESP32 thing is an upgrade to boards based on the popular ESP8266. What the 32 version has to offer on top? Well one of the largest upgrades is support for Bluetooth communications and nearly 30 I/O pins. Makes it pretty perfect for any IoT solution, right?

ESP8266 Thing Dev board from Sparkfun is a reliable, strong solution for IoT projects. The ESP8266 is a well-known WiFi controller from the boards such as NodeMcu and or WeMos. This board increases the reliability to maximum though. This version comes with headers.

ESP8266 Thing Dev board from Sparkfun is a reliable, strong solution for IoT projects. The ESP8266 is a well-known WiFi controller from the boards such as NodeMcu and or WeMos. This board increases the reliability to maximum though. This version comes without headers.

The SparkFun WiFi ESP8266 Shield is a shield for Arduino R3 R3 board enabling internet connection. ESP8266 as you all know is a solid fundament for any IoT project an in this version it can be simply and easily put on your board. It is a great middle ground between the sole module and the development board such NodeMcu or WeMos. So if you need a relatively cheap and super reliable way to internet for your Arduino project - this is the shield for you! ESP8266 shield WiFi comes with an AT-command firmware, hence can be controlled by any UART. It works great with any Arduino R· layout. The shield doesn´t have the headers on.

Digispark is a development board based on the ATTINY85 microcontroller from ATMEL born in a successful campaign on Kickstarter.
Similar to the Arduino line , It is one of the smallest boards on the market.
Programmable directly from USB with the same Arduino tools. It has a built-in Micronucleus bootloader and can be replaced by similar ones such as the Trinket bootloader. Adafruit or others.
You can use many of the same Arduino libraries and you have your own on the digispark wiki. Arduino compatible Attiny85 Digispark board features:
- USB power supply
- External power supply (7v-35v DC 12v maximum recommended)
- 5V DC 500mA regulator on board
- Programmable with the Arduino IDE
- Loaded with Micronucleus bootloader

Sensor used for measuring of the object acceleration in 3 axis in the range of either ±2g, ±4g or ±8g. It is powered with 1.95V to 3.6V. What sets this module apart is its user-friendliness, compatible size and low power consumption. It comes with QWIIC connectors

Digispark is a development board based on the ATTINY85 microcontroller from ATMEL born in a successful campaign on Kickstarter.
Similar to the Arduino line , It is one of the smallest boards on the market.
Programmable directly from USB with the same Arduino tools. It has a built-in Micronucleus bootloader and can be replaced by similar ones such as the Trinket bootloader. Adafruit or others.
You can use many of the same Arduino libraries and have your own on the digispark wiki. Attiny85 Digispark USB Development Board features:
-USB power supply
-External power supply (7v-35v DC 12v maximum recommended)
-5V DC 500mA regulator on board
-Programmable with the Arduino IDE
-Loaded with Micronucleus bootloader

Sensor used for measuring of the object acceleration in 3 axis in the range of either ±2g, ±4g or ±8g. It is powered with 1.95V to 3.6V. What sets this module apart is its user-friendliness, compatible size and low power consumption. it comes with headers attached

It is a version without headers of a popular BOB-09868 from SparkFun.

In our offer, we have a versuib with headers (SP0001) and with QWIC system (SP0005).

This product is a ZQ28335 development chart for learning including a TMS320F28335 processor with very broad features:. DSP Learning Board ZQ28335 DSP28335 Microprocessor TMS320F28335 features:
- Main processor TMS320F28335 32-bit digital high-speed floating point processor, the maximum working frequency is 150 MHz
- Memory on the chip: FLASH: 256Kx16 bit; SRAM: 34Kx16bit; Boot ROM: 8Kx16bit; OTP ROM: 1Kx16bit
- Peripherals on the chip: ePWM (improved PWM version): 12 tracks; HRPWM (high resolution PWM): 6 tracks; EQEP (enhanced version orthogonal coding pulse unit): 2 channels; ADC: 2X8 channels, 12 bits, 80 ns conversion time, 0 ~ 3V range

This board features and extremely low power LIS331HH accelerometer. The unit is a MEMS three axis linear accelerometer with a I2C- SPI serial interface enabling use with embedded applications. The range of measurement includes three options +-6g/+-12g/+-24g and enables datalogging with output rates fro 0.5 Hz to 1kHz. Check this and plenty of other accelerometers in our offering of both Sparkfun and other producers

This product is an SXD28335_QFP learning chart for development including a TMS320F28335 processor with very broad features:. DSP Learning Board C2000 DSP28335 Processor Texas Instruments TMS320F28335 features:
Letter SXD28335_QFP - Description of material: - Main processor TMS320F28335 32-bit digital high-speed floating point processor, the maximum working frequency is 150 MHz
- Memory on the chip: FLASH: 256Kx16 bit; SRAM: 34Kx16bit; Boot ROM: 8Kx16bit; OTP ROM: 1Kx16bit,
- Peripherals on the chip: ePWM (improved PWM version): 12 tracks; HRPWM (high resolution PWM): 6 tracks; EQEP (enhanced version orthogonal coding pulse unit): 2 channels; ADC: 2X8 channels, 12 bits, 80 ns conversion time, 0 ~ 3V range

This accelometer is powered with 1.8 to 3.6V and consumes only up to 320 uA of current. The circuit fits on the small 18mm on 18mm board and is fully compatible with Arudino

The Spectrum Digital XDS100v2 is the second generation of the XDS100 family of debug probes (emulators) for IT processors.
The XDS100 family presents the lowest cost of the entire XDS family of debug probes while supporting the traditional JTAG standard (IEEE1149.1).
In addition, all XDS debug probes support Core and System Trace on all ARM and DSP processors that have an Embedded Trace Buffer (ETB). The Spectrum Digital XDS100v2 connects to the target board via a 14-pin TI connector and to the computer via high-speed USB 2.0 (480 Mbps).
It also requires a license of Code Composer Studio „¢ IDE running on the computer.
Support for Code Composer Studio V4 (Does not support Code Composer Studio V3.3). XDS100V2 Emulator DSP/ARM CCS4/5/6 XP/ WIN7/8/>

Sensor used for measuring of the object acceleration in 3 axis in the range of either ±2g, ±4g or ±8g. It is powered with 1.95V to 3.6V. What sets this module apart is its user-friendliness, compatible size and low power consumption. it comes with headers attached

The SparkFun weather meter kit is a set of basic mechanical components for building a weather station. This kit represents the three basic elements of weather measurement: wind speed, wind direction and precipitation. Whether you are a farmer, a professional meteorologist or a weather enthusiast, building your own weather station can be a truly rewarding project. However, when it comes to measuring the weather, you need some pretty specialised sensors.

CPU Model: Allwinner H5
Number of Cores: 64-bit Quad-Core
Frequency:4* Cortex-A53 1.5GHz Memroy RAM: 1GB DDR3 Storage eMMC: 8GB
MicroSD Slot: MicroSD*1 for external storage up to 128GB Connectivity Ethernet: Gbps Ethernet, RTL8211E-VB-CG chip
WiFi: 802.11b/g/n
Bluetooth: 4.0 dual mode
Antenna: IPX Connector*1 Audio Input/Output: 2.0mm pitch 5 pin-header USB USB 2.0*1: USB 2.0 Host Type A
USB pin header*2
MicroUSB*1: Power input(5V/2A) Pin-header GPIO 1: 24Pin, 2.54mm pitch double-row pin-header containing UART, SPI, I2C and IO GPIO 2:
12Pin, 2.54mm pitch pin-header containing USB, IR receiver,I2S and IO Serial Debug Port: 2.54mm pitch 4pin-header Button Power Key*1
Reset Key*1
MASKROM(BOOT) Key*1

The SparkFun Weather Meter Kit is a set of basic mechanical and electronic components to build a weather station. With the SparkFun Arduino IoT Weather Station kit in sight, you can create your own weather station. The kit allows monitoring via the Arduino Cloud, an IoT platform.

This one is a classic! Hardkernel, company of the fathers of well-known ODROID microcomputers, has hit the sweet spot with this old-school GameBoy emulator. Design your own games and improve the existing ones with only Arduino IDE knowledge!

This development board is specially designed to work with the Bare conductive Electric Paint, which makes it possible to convert touch into sound, light or any action you want. With its 12 capacitive electrodes you can create a multitude of innovative projects and scenes, combining them with the Electric Paint. It has an MP3 decoder and a MIDI synthesizer, as well as a 3.5 mm audio connector and support for micoSD cards (includes 128 MB microSD). It is based on the Arduino Leonardo and uses the ATmega32U4, which works at 16MHz and 5V. 

Do projects on touch and interactive proximity detection in a different and simple way thanks to this Touch Board.

Antenna for NanoPi NEO Plus2 IPX Connector

NVIDIA Jetson Nano Module (B01), Production-Ready AI System On Module (SOM), 4GB 64-bit LPDDR4 with 16GB EMMC Flash.

The reComputer J101 carrier board  is an NVIDIA Jetson Nano compatible support board, rich in cost and interface. It includes HDMI2.0, 2x USB 2.0, 1x USB 3.0, micro SD card slot, 2 xCSI, M.2 key E WIFI / BT, GPIO, I2C, I2S, Fan, and other rich peripheral interfaces. It has almost the same functional design and exactly the same size as the NVIDIA® Jetson Nano™ B01 Developer Kit carrier card.

This BeagleBone® development board is a powerful single board computer (SBC) Open source hardware design.

Seeed Studio BeagleBone® Green Wireless Development Board(TI AM335x WiFi+BT)

It is a low-power, high-sensitivity Ublox chip-based GPS receiver module that can receive 56-channel satellite signal. Compared with traditional GPS receivers, it offers much more accurate and faster positioning performance with stronger signals. Integrated with a built-in receiver antenna, this product adopts high-precision positioning chip and industrial grade manufacturing process.

BeagleBone Green (102010027) is a powerful single board computer (SBC). The main change is the replacement of the HDMI interface with 2 Grove connectors. Grove is a great invention by Seeed, it is a standardised modular connector prototyping system that allows for solder- and cable-free applications. It uses the open source hardware design BeagleBone.

This Seeeduino XIAO is the smallest board in the Arduino-compatible Seeeduino family. It is an Arduino microcontroller, integrated with the ESP32-C3 RISC-V microchip. Despite its tiny size, it has enough interfaces for a multitude of applications. MCU board with Wi-Fi and Bluetooth 5.0, supported battery charging, energy efficiency and rich interface.

reComputer J4012-Edge AI Device with NVIDIA Jetson Orin™ NX 16GB module, 4xUSB 3.2, M.2 Key E & Key M Slot, Aluminum case, Pre-installed Jetpack System with NVIDIA JetPack™ on 128GB NVMe SSD

reComputer  J3011-Edge AI device with NVIDIA Jetson Orin™ Nano 8GB module, 4xUSB 3.2, WiFi/BT, M.2 Key E and Key M slot, aluminium case, Jetpack system pre-installed with NVIDIA JetPack™ on 128GB NVMe SSD.

It is an 8-megapixel camera with a 160-degree field of view, equipped with a chip Sony IMX219.  The camera is designed for NVIDIA Jetson Nano and NVIDIA Jetson Xavier NX development kits.

It's a tiny board, programmable from the Arduino IDE, that hides enormous potential. The Teensy 4.0 is equipped with a 32-bit ARM Cortex-M7 processor at a blazingly fast 600 MHz. The use of the NXP iMXRT1062 chip makes the Teensy 4.0 the fastest microcontroller on the market at launch. 

SparkFun Qwiic Shield for Teensy is a quick and easy way to prepare an expansion board equipped with Qwiic connectors . This shield is compatible with Teensy 4.0, Teensy 3.2 and Teensy LC boards. The board is equipped with an I2C bus connector (GND, 3.3 V, SDA and SCL) and four SparkFun Qwiic connectors