Nokia Graphic LCD 84x48 5110 3310 SPI White The display is compatible with the PCD8544 controller. Ideal for projects with ARDUINO. You can use it with PIC, AVR, STM32 . Characteristic: - LCD screen, 48x84 pixels - Vcc supply 2.7-3.3V - Voltage LED backlight 2.7-3.2V - Compatible PCD8544 controller - SPI interface - PCB dimensions (mm): 45x45 - Includes solder pins - The screen may have small stripes Code P0003 Available Price €2.95
HC-SR501 Motion Detector Module Passive Infrared PIR Sensor Arduino compatible IR motion detector with a detection range of 7 meters and an operating angle of 120º. An electric pyro sensor , which can detect infrared radiation levels - detect a change in the average IR levels of your detection zone. Ideal for projects with ARDUINO, PIC, AVR, STM32. HC-SR501 Motion Detector Module Passive Infrared PIR Sensor features: - Infrared sensor with control circuit - Adjustable sensitivity and time - Operating voltage: 4.5V- 20V - Consumption in Idle state: Code S0003 Available Price €1.79
Motor 28BYJ-48 5V Stepper The 28BYJ-48 has everything you need to start using stepper motors in your project. A stepper motor converts digital impulses into small movement steps. in one direction Characteristic: - Motor model: 28BYJ-48 - Motor phases: 4 - Operating voltage: 5V - Frequency: 100 Hz - Operating current: 200mA - Max Power: 20W - Winding resistance: 70 ohm - Angle per step: 5,625º - Steps per lap: 64 - Torque: 0.3 Kgr / cm - Speed: 1900 rpm - Operating temperature: -45ºC to + 125ºC - Motor cable length: 19cm - Motor block diameter: 28mm - Motor dimensions: 42mm x 32mm x 30mm Code R0044 Available Price €2.29
Resistor 1K Ohm 5% 0,25W 1/4W Resistor 1K Ohm 5% 0,25W 1/4W features:-1K Ohm-Type: Carbon film-Tolerance: ±5%-Power: 0.25W-Dimensions: 2x7mm Code D0013 Available Price €0.08
Sensor Module Moisture Earth Water Soil The module has two outputs: analog A0 and digital D0 Digital output D0 - signal 0 appears or 1 depending on the threshold setting The threshold is set with the potentiometer The sensor can be used for example: Automatic watering for potted plants With this module you will be able to measure the humidity of the soil, so that you will be able to control the humidity level of the soil of your plants Characteristic: Operation: 3.3V -5V - Sensitivity adjustable by potentiometer - Dual output mode: analog and digital - Red LED - power indicator - Green LED - indicator digital switching output - PCB measurements: 3 x 1.5 cm - Probe measurements: 6 x 3 cm Code S0021 Available Price €1.95
140x Jumper Wire Kit 140x Jumper Wire Kit features: -Quantity: 140 pieces of different lengths and colors in small box compartments-Box measures: 170x55x15mm Code K0011 Available Price €2.90
5x Electrolytic Capacitor 1000uF 35V 105ºC PIC for Arduino 5x Electrolytic Capacitor 1000uF 35V 105ºC PIC Arduino features:-Type: Electrolytic Capacitor-Assembly: intern-Value: 1000uF-Maximum tension: 35V-Maximum temperature 105º C-Dimensions: 13x21mm-Quantity: 5 units Code D0048 Available Price €0.39
Batch of 600 Units 1/4W Resistors Various values Ohm Ω Batch of 600 Units 1/4W Resistors Various values Ohm Ω features: - Each lot contains (30 x 20 units): 10Ω, 22Ω, 47Ω, 100Ω, 150Ω, 200Ω, 220Ω, 270Ω, 330Ω, 470Ω, 510Ω, 680Ω, 1KΩ, 2KΩ, 2.2KΩ, 3.3KΩ, 4.7KΩ, 5.1KΩ, 6.8KΩ, 10KΩ, 20KΩ, 47KΩ, 51KΩ, 68KΩ, 100KΩ , 220KΩ, 300KΩ, 470KΩ, 680KΩ, 1M - Tolerance: ± 5% - Power: 0.25W Code D0070 Available Price €3.95
XDS100V2 Emulator DSP/ARM CCS4/5/6 XP/ WIN7/8/10 00IC USB2.0 Supports TI DSP/Core The Spectrum Digital XDS100v2 is the second generation of the XDS100 family of debug probes (emulators) for IT processors.The XDS100 family presents the lowest cost of the entire XDS family of debug probes while supporting the traditional JTAG standard (IEEE1149.1).In addition, all XDS debug probes support Core and System Trace on all ARM and DSP processors that have an Embedded Trace Buffer (ETB). The Spectrum Digital XDS100v2 connects to the target board via a 14-pin TI connector and to the computer via high-speed USB 2.0 (480 Mbps).It also requires a license of Code Composer Studio „¢ IDE running on the computer.Support for Code Composer Studio V4 (Does not support Code Composer Studio V3.3). XDS100V2 Emulator DSP/ARM CCS4/5/6 XP/ WIN7/8/> Code B0041 Backorder Price €48.95
Camera IMX219-160 8MP 160° FOV - Compatible with NVIDIA Jetson Nano/ Xavier NX It is an 8-megapixel camera with a 160-degree field of view, equipped with a chip Sony IMX219. The camera is designed for NVIDIA Jetson Nano and NVIDIA Jetson Xavier NX development kits. Code SS046 Last items in stock Price €35.99
Metal Case for NanoPi NEO Plus2 Includes Antenna Metal Case for NanoPi NEO Plus2 Includes Antenna features: - Learning charter for development Code B0048 ✗ Out-of-Stock Price €16.50
Spartan Edge Accelerator Board - FPGA Shield for Arduino UNO with ESP32 The Spartan Edge Accelerator Board is an FPGA board developed by Xilinx Spartan in the form of a Shield for the Arduino UNO board. In addition, the integrated ESP32 chip also provides WiFi and Bluetooth functionality. Code SS012 Backorder Price €67.90
BeagleBone® Green Wireless SBC Seeed Studio Development Board (TI AM335x WiFi+BT) This BeagleBone® development board is a powerful single board computer (SBC) Open source hardware design. Seeed Studio BeagleBone® Green Wireless Development Board(TI AM335x WiFi+BT) Code SS030 Last items in stock Price €99.95
BeagleBone® Green SBC Seeed Studio Development Board (AM335x Ethernet) BeagleBone Green (102010027) is a powerful single board computer (SBC). The main change is the replacement of the HDMI interface with 2 Grove connectors. Grove is a great invention by Seeed, it is a standardised modular connector prototyping system that allows for solder- and cable-free applications. It uses the open source hardware design BeagleBone. Code SS045 Last items in stock Price €67.95
DSP Learning Board ZQ28335 DSP28335 Microprocessor TMS320F28335 This product is a ZQ28335 development chart for learning including a TMS320F28335 processor with very broad features:. DSP Learning Board ZQ28335 DSP28335 Microprocessor TMS320F28335 features: - Main processor TMS320F28335 32-bit digital high-speed floating point processor, the maximum working frequency is 150 MHz- Memory on the chip: FLASH: 256Kx16 bit; SRAM: 34Kx16bit; Boot ROM: 8Kx16bit; OTP ROM: 1Kx16bit- Peripherals on the chip: ePWM (improved PWM version): 12 tracks; HRPWM (high resolution PWM): 6 tracks; EQEP (enhanced version orthogonal coding pulse unit): 2 channels; ADC: 2X8 channels, 12 bits, 80 ns conversion time, 0 ~ 3V range Code B0043 ✗ Out-of-Stock Price €90.75
Jetson Nano Developer Kit (4GB) by NVIDIA NVIDIA® Jetson Nano ™ Developer Kit is a small computer with powerful capabilities that allows you to run multiple neural networks in parallel for applications such as image classification, segmentation, speech processing and object detection. All this in an easy-to-use platform that runs on just 5 watts. Thanks to this board, the power of modern Artificial Intelligence is now available to Makers, students and embedded developers everywhere. Discover the power of AI and robotics with the powerful 4GB NVIDIA Jetson Nano Developer Kit. Now educators, students, and any enthusiast can easily perform AI projects quickly and efficiently using their GPU-accelerated NVIDIA software. Code RA095 Last items in stock Regular price €239.99 -€21.00 Price €218.99
Touch Board - Development board for Electric Paint - Bare Conductive This development board is specially designed to work with the Bare conductive Electric Paint, which makes it possible to convert touch into sound, light or any action you want. With its 12 capacitive electrodes you can create a multitude of innovative projects and scenes, combining them with the Electric Paint. It has an MP3 decoder and a MIDI synthesizer, as well as a 3.5 mm audio connector and support for micoSD cards (includes 128 MB microSD). It is based on the Arduino Leonardo and uses the ATmega32U4, which works at 16MHz and 5V. Do projects on touch and interactive proximity detection in a different and simple way thanks to this Touch Board. Code RA119 ✗ Out-of-Stock Regular price €84.90 -€2.00 Price €82.90
Adafruit Feather RP2040 Adafruit's Feather meets Raspberry Pi's new RP2040 chip, offering this board with great features. This Feather features the RP2040 and all the niceties you know and love from Feather. It comes fully assembled and tested, with the UF2 USB bootloader. It also comes with a header, so you can solder it and connect it to a solderless test board. Code AD001 Available Price €11.90
USB GPS Receiver with 2m Extension Cable (Compatible with Raspberry Pi/ LattePanda/ Jetson Nano) It is a low-power, high-sensitivity Ublox chip-based GPS receiver module that can receive 56-channel satellite signal. Compared with traditional GPS receivers, it offers much more accurate and faster positioning performance with stronger signals. Integrated with a built-in receiver antenna, this product adopts high-precision positioning chip and industrial grade manufacturing process. Code RA160 Last items in stock Price €17.95
Touch Board - Development board for Electric Paint - Bare Conductive This development board is specially designed to work with the Bare conductive Electric Paint, which makes it possible to convert touch into sound, light or any action you want. With its 12 capacitive electrodes you can create a multitude of innovative projects and scenes, combining them with the Electric Paint. It has an MP3 decoder and a MIDI synthesizer, as well as a 3.5 mm audio connector and support for micoSD cards (includes 128 MB microSD). It is based on the Arduino Leonardo and uses the ATmega32U4, which works at 16MHz and 5V. Do projects on touch and interactive proximity detection in a different and simple way thanks to this Touch Board. Code RA119 ✗ Out-of-Stock Regular price €84.90 -€2.00 Price €82.90
XDS100V2 Emulator DSP/ARM CCS4/5/6 XP/ WIN7/8/10 00IC USB2.0 Supports TI DSP/Core The Spectrum Digital XDS100v2 is the second generation of the XDS100 family of debug probes (emulators) for IT processors.The XDS100 family presents the lowest cost of the entire XDS family of debug probes while supporting the traditional JTAG standard (IEEE1149.1).In addition, all XDS debug probes support Core and System Trace on all ARM and DSP processors that have an Embedded Trace Buffer (ETB). The Spectrum Digital XDS100v2 connects to the target board via a 14-pin TI connector and to the computer via high-speed USB 2.0 (480 Mbps).It also requires a license of Code Composer Studio „¢ IDE running on the computer.Support for Code Composer Studio V4 (Does not support Code Composer Studio V3.3). XDS100V2 Emulator DSP/ARM CCS4/5/6 XP/ WIN7/8/> Code B0041 Backorder Price €48.95
NVIDIA Jetson Orin™ Nano 8GB - reComputer J3011-Edge AI Device reComputer J3011-Edge AI device with NVIDIA Jetson Orin™ Nano 8GB module, 4xUSB 3.2, WiFi/BT, M.2 Key E and Key M slot, aluminium case, Jetpack system pre-installed with NVIDIA JetPack™ on 128GB NVMe SSD. Code RA180 Backorder Price €849.00
NanoPi NEO Plus2 CPU Model: Allwinner H5 Number of Cores: 64-bit Quad-Core Frequency:4* Cortex-A53 1.5GHz Memroy RAM: 1GB DDR3 Storage eMMC: 8GB MicroSD Slot: MicroSD*1 for external storage up to 128GB Connectivity Ethernet: Gbps Ethernet, RTL8211E-VB-CG chip WiFi: 802.11b/g/n Bluetooth: 4.0 dual mode Antenna: IPX Connector*1 Audio Input/Output: 2.0mm pitch 5 pin-header USB USB 2.0*1: USB 2.0 Host Type A USB pin header*2 MicroUSB*1: Power input(5V/2A) Pin-header GPIO 1: 24Pin, 2.54mm pitch double-row pin-header containing UART, SPI, I2C and IO GPIO 2: 12Pin, 2.54mm pitch pin-header containing USB, IR receiver,I2S and IO Serial Debug Port: 2.54mm pitch 4pin-header Button Power Key*1 Reset Key*1 MASKROM(BOOT) Key*1 Code B0046 ✗ Out-of-Stock Price €52.90
Wio Terminal - ATSAMD51 - RTL8720DN WiFi Bluetooth - Seeedstudio Wio Terminal: ATSAMD51 Core development board with Realtek RTL8720DN BLE 5.0 & Wi-Fi 2.4G / 5G. Arduino and MicroPython compatible, Wio Terminal is an ATSAMD51-based microcontroller with wireless connectivity compatible with Realtek RTL8720DN. Its CPU speed runs at 120MHz (Boost up to 200MHz). The Realtek RTL8720DN chip supports Bluetooth and Wi-Fi, providing the backbone for IoT projects. The Wio terminal itself is equipped with a 2.4 ”LCD screen, integrated IMU (LIS3DHTR), microphone, buzzer, microSD card slot, light sensor and infrared emitter (IR 940 nm). Code SS010 Last items in stock Price €55.49
Jetson Nano Developer Kit (4GB) by NVIDIA NVIDIA® Jetson Nano ™ Developer Kit is a small computer with powerful capabilities that allows you to run multiple neural networks in parallel for applications such as image classification, segmentation, speech processing and object detection. All this in an easy-to-use platform that runs on just 5 watts. Thanks to this board, the power of modern Artificial Intelligence is now available to Makers, students and embedded developers everywhere. Discover the power of AI and robotics with the powerful 4GB NVIDIA Jetson Nano Developer Kit. Now educators, students, and any enthusiast can easily perform AI projects quickly and efficiently using their GPU-accelerated NVIDIA software. Code RA095 Last items in stock Regular price €239.99 -€21.00 Price €218.99
Orange Pi Lite 1GB DDR3 H3 Quad-Core 1.2 Ghz Wifi + antenna Orange Pi Lite is a super small computer This version includes a camera connector. It uses the Allwinner H3 SoC with Quad-core Cortex-A7, and has 512MB/1GB DDR3 SDRAM. It can run Android 4.4,Ubuntu,Debian image. Orange Pi Lite offers a range of different ports, including HDMI output, 40pin headers,USB 2.0, CSI camera port, TF card slot, etc. It is powered through DC. Code RA033 Last items in stock Price €45.90
DSP Learning Board C2000 DSP28335 Processor Texas Instruments TMS320F28335 This product is an SXD28335_QFP learning chart for development including a TMS320F28335 processor with very broad features:. DSP Learning Board C2000 DSP28335 Processor Texas Instruments TMS320F28335 features: Letter SXD28335_QFP - Description of material: - Main processor TMS320F28335 32-bit digital high-speed floating point processor, the maximum working frequency is 150 MHz- Memory on the chip: FLASH: 256Kx16 bit; SRAM: 34Kx16bit; Boot ROM: 8Kx16bit; OTP ROM: 1Kx16bit,- Peripherals on the chip: ePWM (improved PWM version): 12 tracks; HRPWM (high resolution PWM): 6 tracks; EQEP (enhanced version orthogonal coding pulse unit): 2 channels; ADC: 2X8 channels, 12 bits, 80 ns conversion time, 0 ~ 3V range Code B0042 Available Price €79.00
FinestraMiner Helium LoRaWAN Gateway Hotspot Miner FinestraMiner is a highly efficient Helium compatible hotspot that provides wireless network coverage to the Helium network, also called People's Network, the world's largest and fastest growing LoRaWAN network. It allows thousands of IoT devices to connect to this single hotspot using Long-Fi technology, with long-range coverage up to 16 kilometres away. The Helium network is a decentralised wireless network that allows devices anywhere in the world to connect to the Internet wirelessly. Code W0800 Available Price €675.00