Arduino Modules

Wired Bone Conductor Transducer - 8 Ohm 1 Watt
This amazing speaker does not have a movable cone like most From the speakers you've seen, instead, a small metal rod is wrapped with the voice coil.
When the current is driven through the coil, the magnetic field makes a piece of metal expands and contracts, if pressed against a flat surface or cavity makes it a speaker! Often these size transducers are pressed against the jaw or ear bone to turn the skull into a speaker socket.
The effect is a perfect quality sound that comes from your head and no one else can hear it. You can also press it against your elbow bone and stick a finger in your ear to listen to the audio transmitted through your arm!

MAX98306 3.7W Stereo Amplifier - Class D Stereo Audio Amplifier 8 Ohm.

- Bluetooth 4.0 AT-09 BLE Master / Slave module with 6-pin connection base
- This module is very similar to HM-10 module
- Bluetooth protocol: Bluetooth V4.0 BLE specification
- Ultra-low power consumption, in 90uA standby mode
Wireless Module AT-09 Bluetooth 4.0 CC2541 IOS BLE features:

- Chipset based on CC2541
- Bluetooth Class 2
- Industrial level Bluetooth module SPP
- Flash 256Kb
- Integrated chip antenna
- Power supply: + 3.3 VDC 50 mA
- Working temperature: -5 C to + 60 C
- Operating frequency: 2.4 GHz ISM Band
- Modulation method: GFSK (Gaussian Frequency Shift keying)

This module has three modes (control, music and bluetooth). The audio files can be saved on the U disk and on the TF card.
Its remote control allows you to control the audio output (volume down or up, music change, mode change). Bluetooth Decoder Module Amplifier Audio Receiver USB TF features:
- Interfaces:
       - 5V micro USB supply
       - USB audio
       - U disk
       - LED
       - TF card
       - IR remote
       - AD key interface to connect external circuits
       - Bluetooth decoder
       - 3.5mm stereo output
       - Left and right 3W channels handling speaker
       - 2 3W amplifiers
- Supply voltage: 3.7-5VDC
- Signal / noise ratio (SNR): 90 dB

This module is a three way switch ( COM, NO and NC ) that uses the intensity of the ambient light to control directly the load at the output. Its adjustment potentiometer allows changing the sensitivity and setting the start threshold of the relay. The relay is energized when it is darker than the threshold.

This module is used to extend the Raspberry's 40 GPIO pins to another set of 2x20 male pins and 8 parallel pins accessible on the terminal blocks in the that test leads are pushed. The electronic board offers great reliability with the Raspberry and is very easy to connect thanks to its existing suitable accessories but not included.
The module offers a set of mini jumpers to configure the GPIO.

This external wireless antenna module CC1101 is suitable for Funduino and Arduino projects.
The CC1101 module of 1.2K baud consists of a domestic R & Lotes unit to improve the effective communication distance.
This is a significant improvement over the CC1100 module.
It allows to adjust the speed of the bits for different uses, thus allowing a higher transmission speed.
Supports 2-FSK, GFSK and msk modulations. It also has a high sensitivity (1.2kbps @>

This module specially designed for Arduino will allow you to generate a light of any color (RGB) quickly and accurately.
The SMD LED Module RGB, consisting of an LED capable of creating any color using RGB, has a PWM voltage input with three pins.
These are capable of shining in a wide range of colors thanks to the mixture of the three primary colors (red , green and blue). These types of diodes are called RGB and are made up of three red, green and blue diodes in the same package.
Thanks to the variation of the intensity of these three diodes, we can create a composition of colors. With this led you can handle more than 16.5 million colors.

This module specially designed for Arduino will allow you to generate a light of any color (RGB) quickly and accurately.
The LED Bulb Module RGB, consisting of an LED capable of creating any color using RGB, has a PWM voltage input with three pins. These are capable of shining in a wide range of colors thanks to the mixture of the three colors. primary (red, green and blue).
These types of diodes are called RGB and are made up of three red, green and blue diodes in the same package.
Thanks to the variation of the intensity of these three diodes, we can create a composition of colors. With this led you can handle more than 16.5 million colors.

Blue LED.
The color option allows you to adjust the LEDs to your liking to sew clothes or anything else you can dream of.
Lilypad is a wearable E-textile technology developed to have large connection pads to attach to clothing. Lilypad LED Blue features:
- Operating voltage: 3 - 5 VDC
- Very bright
- Density of the PCB: 0.8 mm
- LED color: blue
- Size: 5.5x12.5 mm
- 1 LED included

LED of red color.
The color option allows you to adjust the LEDs to your liking to sew clothes or anything else you can dream of.
Lilypad is a wearable E-textile technology developed to have large connection pads to attach to clothing. Lilypad LED Red features:
- Operating voltage: 3 - 5 VDC
- Very bright
- Density of the PCB: 0.8 mm
- LED color: red
- Size: 5.5x12.5 mm
- 1 LED included

LED green.
The color option allows you to adjust the LEDs to your liking to sew clothes or anything else you can dream of.
Lilypad is a wearable E-textile technology developed to have large connection pads to attach to clothing. Lilypad LED Green features:
- Operating voltage: 3 - 5 VDC
- Very bright
- Density of the PCB: 0.8 mm
- LED color: green
- Size: 5.5x12.5 mm
- 1 LED included

This support is a lilypad button to sew clothing or anything else you can dream of.
Lilypad is a wearable E-textile technology developed to have large connection pads to attach to clothing. Lilypad Button Board features:
- Density of the PCB: 0.8 mm
- Size: 8x16 mm
- 1 LED included

This module is a small source of energy, this board was designed to be as small and as indiscreet as possible.
Putting a battery type AAA and operating the power switch, will have a supply of 5 V to power a lilypad circuit.
Use up to 200ma, it is protected against short circuits. This card has AAA battery clips but can use a 1.2V to 5V input, the module increases the voltage up to 5V.
Lithium polymer batteries are an alternative to rechargeable batteries.
Lilypad is a wearable E-textile technology developed to have large connection pads to attach to clothing. Lilypad Power Supply 5V Step Up with AAA Batteries features:
- Type of batteries connectable: AAA
- Input voltage (of the batteries): from 1.5V to 5V
- Output voltage: 5V

This is a simple slide switch for LilyPad. Use it as a simple On / Off switch, or to control LEDs, buzzers, sensors, etc.
The switches in each panel have a capacity of 4V to 300 mA, but will operate at 5V with a current reduction.
Lilypad is a wearable E-textile technology developed to have large connection pads to attach to clothing. Lilypad Slide Switch Board 2 Positions Interruptor features:
- Switch two positions: On (ON) / Off (OFF)
- Density of the PCB: 0.8 mm
- Size: 7.75x18.1 mm

Blink any color you need! Use the Tri-Color LED board as a simple indicator, or by pressing the red, green and blue channels, you can create any color. Very bright output.
This is a common anode design: to turn on a channel, you simply need to ground one of the R / G / B pins to illuminate that channel.
Lilypad is a wearable E-textile technology developed to have large connection pads to attach to clothing. Lilypad Tri-Color LED RGB features:
- Operating voltage: 3 - 5 VDC
- Design of common anode
- Density of the PCB: 0.8 mm
- Outside diameter: 20 mm

The buzzer plate for Lilypad is used for the development and application of configurations that require a buzzer to indicate, for example, warnings, warnings or as part of the correct operation of your device.
Lilypad is a wearable E-textile technology developed to have large connection pads to attach to clothing. Lilypad Buzzer features:
- Operating voltage: 5 VDC
- Design of common anode
- PCB density: 0.5 mm
- Density of the buzzer: 20 mm
- Outside diameter: 20 mm

The pixel board is equipped with a WS2812 that is actually RGB LED with a WS2811 built into the LED.
Several of these individual sessions can be chained together to form a screen or an addressable string.
Each LilyPad is creatively designed to have large connecting pads so that they can be sewn on clothes. Pixel Board WS2812 for Lilypad features:
- Use the WS2812S chip
- RGB color lights
- Each LED can be controlled individually
- You only need one control line and two power cables
- Arduino libraries and routines available
- Density of the PCB: 0.8 mm
- Size: 20x3 mm

The good thing about LiPower is the ability to use rechargeable lithium polymer batteries.
These batteries are smaller, flatter and last much longer than an AAA battery.
Connect a single-cell LiPo battery, turn on the power switch and you will have a 5V supply to power your LilyPad network. It can deliver the current up to 150mA. Protected against the short circuit.
This board has a JST connector, which will be connected to single cell LiPo batteries terminated in JST.
It also has terminals for charging the LiPo battery with LiPo chargers. Each LilyPad was creatively designed to have large connection pads that allow them to sew on clothes.

This XBEE module contains everything you need to create your projects, including socket to mount an XBee device, VDC power pins, GND, terminal block to power a servo motor, reset button and much more. The new expansion IO Shield V7.1 offers several advantages and these are its characteristics.
Compatible with the new Arduino Due.

It is a mini GPS module including a NEO-6M chip and an EEPROM memory chip.
The SMA antenna port is On-board IPEX and cell phone button battery ensure robust positioning efficiency and fast satellite discovery speed.
Serial port provides simple initial knowledge to stay in touch with the most compatible Arduino-compatible MCU STM32. Characteristic: - Supply voltage: 3.3 - 5 VDC
- Operating current: 45 mA
- Communication speed: 9600 Bauds configurable from 4800 to 115200 Bauds
- Navigation update: 5 Hz max. (1 Hz default)
- Capture time: at the start 27s, in operation 1s
- Operating temperature: -40 ° C - + 85 ° C
- separate GPS antenna (not included ): 18x18 mm
- Size: 22x30x13 mm

It is a mini GPS module including a NEO-6M chip and an EEPROM memory chip.
The SMA antenna port is On-board IPEX and cell phone button battery ensure robust positioning efficiency and fast satellite discovery speed.
Serial port provides simple initial knowledge to stay in touch with the most compatible Arduino-compatible MCU STM32. Characteristic: - Supply voltage: 3.3 - 5 VDC
- Operating current: 45 mA
- Communication speed: 9600 Bauds configurable from 4800 to 115200 Bauds
- Navigation update: 5 Hz max. (1 Hz default)
- Capture time: at the beginning 27s, in operation 1s
- Operating temperature: -40 ° C - + 85 ° C
- separate GPS antenna 18x18 mm - Size: 22x30x13 mm

The DC-DC 25A solid state relay has a 3-32VDC input and a 6-60VDC output. It has a maximum load capacity of 25A.
It has a long operating life and high reliability, a compact size. This relay switches very quickly. Fotek SSR-25 DD 25A DC-DC Solid State Relay 5V-60VDC output 

The DC-AC 12A solid state relay has a 3-32VDC input and a 24-380VAC output. It has a maximum load capacity of 12A.
It has a long operating life and high reliability, a compact size. This relay switches very quickly. Solid State Relay SSR-25 DA 12A DC-AC Output 24V-380VAC 

This module is a three-way switch (COM, NO and NC) that uses the intensity of the ambient light to directly control the output load. Its adjustment potentiometer allows you to change the sensitivity and set the threshold for starting the relay. The relay is energized when it is darker than the threshold.
The optical isolation relay effectively protects the chip and ensures better performance.
This module is used for light detection, brightness detection , control of lamps and automatic equipment. Characteristic: - Channels: 1
- Supply voltage: 12VDC
- Output load capacity: 250V 10A AC / 30V 10A DC
- Relay activation current: & gt; 100mA
- Insulation: Yes
- Indicator LED: Green and Red
- PCB size: 5x2.6 cm / 1.96x1.02 "

This module works under the characteristics of the integrated ISD1820 and allows you to make recordings of multiple messages or the reproduction thereof, it performs a non-volatile storage. Voice Recording and Reproduction Module ISD1820 features:
- Working voltage: 2.4 - 5.5 VDC
- Model: I073103
- Voice Recorder Chip ISD1820
- Automatic ignition mode dwon
cording duration: 8-20 seconds
- Manual or Automatic Control with an MCU
- With internal audio amplifier, this board can drive 8 ohm 0.5W speaker directly
- Includes a microphone on board to record directly
- The sampling frequency and duration can be different if a single module resistance is changed
- High quality, restored natural voice, can be used as a speaker module

The multifunctional relay control module, FRM01, is designed for customers with different synchronization and control needs.
The FRM01 is controlled by the STM8S003F3P6 microcontroller and has 18 different functions.
Each function can be customized to meet customer needs in a variety of time and power control applications.
The FRM01 is equipped with a high-quality power relay, a high-power voltage transistor, red and blue LED indicators, an LED display on a double-sided PCB board.
The output of the board is driven by a high quality power relay capable of controlling the AC and DC loads. Timer Relay Module FRM01 features:
- Operating voltage: 12 VDC
- 4 buttons: SET, SWI, NUM +, NUM-
- Operating temperature: -20 °C - + 60 °C

This module is a timed switch that allows you to program several types of applications such as lights. Time Switch Module 12V NE555 Monostable Switch Delayed features:

This product is a Bluetooth module BLE 4.0 UART without adapter, low energy with serial transceiver.
Logic level conversion circuit. No external level of 5V is needed to become a 3.3V level.
The power input port is protected against the anti-circuit, to avoid the inverted accidental power plug, which leads to the module burn
HM-10, Bluetooth module HM-11 series using IT chip CC2540 / 2541, configuration 256Kb space, support
In commands.
You can change the paper (master and slave mode) and the baud rate, the device name, the pairing of the password and other parameters, convenient and flexible. BLE 4.0 UART Bluetooth Low Energy Module without Adapter features:
- Version AT-09 CC2541 Arduino Android IOS BLE
- Serial transceiver

This module is an active buzzer for Arduino and emits different sounds at various frequencies.
It does not accept oscillation source, it only receives square waves for drive sound. 

This module is a passive buzzer, a low trigger level alarm for Arduino. It emits different sounds at various frequencies. The buzzer sounds when the I / O port input is low level. 

When the input port is low, the trio turns on. Then the doorbell comes on and a small red light comes on.
It can be used as the external module for many types of circuits, such as MCUs. Passive Buzzer 3-5V Low Level Trigger features:
- Operating voltage: 3.3-12 VDC
- Current consumption:

XY-V17B is a smart voice module, integrated IO segment trigger, control UART series, ONE_line control of a single serial bus, MP3 standard and other functions; Supports MP3, WAV format decoding, maximum storage capacity on 32G TF card, update audio files from TF memory card via USB data cable to connect computer.
Voice Module MP3 Player features:

- Support MP3, WAV decoder format.
- Support sample rate ( KHz): 8 / 11.025 / 12/16 / 22.05 / 24/32 / 44.1 / 48.
- 24-bit DAC output, support 90dB dynamic range, support 85dB signal-to-noise ratio.
- Fully compatible with FAT16 / FAT32 file system, 32G TF card with maximum support, 32G U disk support.

The adaptor for the well-known ESP-12 and ESP-12E module

Buzzer 5V Passive 5 to 12V DC features:
- Input voltage: 4V to 12V
- Diameter: 17mm
- Height: 7mm
- f = 4kHz +/- 500
- Pin Separation: 10mm
- Maximum Current:

This mini vibration motor runs on 5 VDC and can be used for Arduino and Raspberry projects. It is a direct current motor.
Mini vibration engine for Arduino and Raspberry Pi 5 VDC features:
- Voltage: 5 VDC,
- Current: 75mA,
- Rotation speed: 1100 (rpm),
- Efficiency: 80%,
- Dimensions: 10x27mm.

Can be used in Access Control projects and Alarm, Arduino, Raspberry PI, PIC, AVR projects 10x NFC RFID round card 13.56 MHz features:
- 32 bit unique code
- Protocol: ISO14443
- Compatible with Mifare S50 Classic
- Memory: 1kB EEPROM
- Operating frequency: 13.56MHz
- Communication speed: 106Kboud
- Reading distance: 2.5-10CM
- Reading time: 1-2MS
- Working temperature: -20 ºC to 85 ºC
- Number of uses 100,000 times
- Data retention: 5 years
- Material: PVC
- Dimensions: Ø 25 x 0.8 mm
- Quantity: 10 units of NFC 13.56MHz card

This Openlog serial data module is an open source logger that works with a serial connection Simple and supports Micro SD cards up to 64GB. It can store or record huge amounts of serial data and act as a black box. It includes an ATMega328P chip with a high frequency of 16 MHz. All recorded data will be stored on the Micro SD card.

The new SensorTag IoT kit invites you to realize your product idea connected to the cloud.
The new SensorTag now includes 10 low-power MEMS sensors in a small red package.
And it's expandable with DevPacks to make it easy to add your own sensors or actuators.
Connect to the cloud with low-power Bluetooth and Get your sensor data online in 3 minutes.
The SensorTag is ready to go right away with an iOS and Android app, no programming experience to get started.
The new SensorTag is based on The CC2650 Wireless MCU, which offers 75% less power consumption than previous Bluetooth low energy products.
This allows the SensorTag to run on batteries, and offers years of battery life with a single coin cell battery.