PLA Filamento 1.75mm 0.85kg Graphite color grafito Premium Bobina para Impresora 3D Code I0405 Backorder Price €14.45
10x Tactile Tact Push Button Switch 6x6x8mm 10x Tactile Tact Push Button Switch 6x6x8mm features:- Tactile Push Tact Switch mini electronic Arduino pushbutton- Measures: 6x6x8mm- Quantity: 10 units Code K0076 Available Price €0.12
Adjustable Module Buck Converter DC 3A 1,6-26V MP1584 Step-Up Down Adjustable Module Buck Converter DC 3A 1,6-26V MP1584 Step-Up Down features:- Based on the MP1584EN regulator- Output Voltage: 1.6V - 26V DC (adjustable)- Input Voltage: 4.5V - 28V DC- Max. Output Current: 3A (with heat sink)- Frequency: 1MHz- Conversion Efficiency (1A): 94%- Short circuit protection- Protection against overheating- Operating temperature: -40ºC to + 85ºC- Measures 22 x 17 x 4 mm Code A0007 Available Price €1.61
Matrix Membrane Keyboard 4x4 Modulo High-quality membrane keyboard, with 16-key matrix, ultra-thin, less than 1mm thick, with adhesive system on the reverse side. Ideal for your Arduino projects, but can also be used with other microcontrollers. Matrix Membrane Keyboard 4x4 Modulo features: - Rating circuit, Max: DC 35V 100 mA - Cable length: 85 mm - Dupont 8 pin connector - Specific insulation: 100 M Ohm, 100V - Useful life: + 1 million uses - Contact parting: Code M0025 Available Price €1.48
HC-SR04 Ultrasonic Sensor Distance Measuring Module It is very easy to make it work with an Arduino, PIC or any other microcontroller. In its output pin we will be able to measure the PWM pulse width depending on the distance of the obstacle. HC-SR04 Ultrasonic Sensor Distance Measuring Module features: - Supply voltage: 5V (4.5V- 6V) - Consumption: 30 mA typical, (35 mA max) - Interface: VCC , GND, Signal - Range: 2 cm to 3 meters - Angle 15º - LED indicator of measurement in progress - Frequency: 40 kHz for 200 µs - Size: 30mm x 20mm - Quantity: 1 unit Useful links for Arduino / Raspberry programming and projects with boards Arduino / Raspberry: Automatic robot operation with obstacle detection /> Code S0007 Available Price €1.48
40x Female-Female Cable 20cm 40x Female-Female Cable 20cm features: -Length: 20cm -Quantity: 40 wires -Dupont female connectors on both ends -Compatible with 2.54mm male connectors -High quality and good working condition -Easy to install and use Code K0004 Available Price €2.06
TCRT5000 Module 3.5cm IR infrared sensor The optical (reflective) module sensor with LM393 comparator, which detects obstacles with high accuracy. The ideal detector for obstacle detection for the installation of intelligent robots.TCRT5000: reflective optical sensor that has a compact construction where the light emitter and receiver are placed in the same direction to detect the presence of an object using infrared reflection on the object. The transmitter is an infrared LED and the receiver is a phototransistor. The sensor allows the detection of an object at a distance of up to 3.5 cm from the white paper and 1 cm from the person's finger. Code S0138 Last items in stock Price €1.40
Rechargeable battery XTAR 18650 2200mAh Li-ion Rechargeable battery XTAR 18650 2200mAh Li-ion features: - With PCB protection circuit that protects the battery against overcharges and over discharges, increasing battery life - Quantity: 1 unit - Authentic Protection Battery Code PP019 Last items in stock Price €7.43
RFID PN532 NFC Module NFC module for Educational STEAM Kit. Near field communication (NFC) is a set of standards for smartphones and similar devices to establish radio communication with each other by touching them together or bringing them into close proximity, usually no more than a few centimeters. Compatible with almost any microcontroller, Arduino, PIC, AVR. It can be used in Access Control projects and Alarm projects. RFID PN532 NFC Module features: - Based on the NXP PN532 chip, it can be used for non-contact communication of 13.56M.- Greater effective communication distance of 3 cm. Code W0092 Last items in stock Price €9.83
NFC RFID Keychain Tag 13.56 MHz NFC RFID Keychain Tag 13.56 MHz features: - 32 bit unique code - Protocol: ISO14443 - Compatible with NFC Mifare 1k - Memory: 1kB EEPROM - Operating frequency: 13.56MHZ - Communication speed: 106Kboud - Reading distance: 2.5-10CM - Reading time: 1-2MS - Working temperature: -20ºC to 85ºC - Number of uses 100,000 times - Data retention: 10 years - Material: ABS - Dimensions 40.5 x 32 x 4.2 mm Code M0030 Available Price €0.82
RFID PN532 NFC Module with Card and Pendant NFC module for Educational STEAM Kit. Near field communication (NFC) is a set of standards for smartphones and similar devices to establish radio communication with each other by touching them together or bringing them into close proximity, usually no more than a few centimeters. Compatible with almost any microcontroller, Arduino, PIC, AVR. It can be used in Access Control projects and Alarm projects. RFID PN532 NFC Module with Card and Pendant features: - Support i2C, SPI, High Speed UART - Support RFID reading and writing - Support P2P communication with peers - Support NFC with phone - Work in NFC Mode or RFID reader/writer Mode - RFID reader/writer supports: - 1k, 4k, Ultralight, and DesFire cards ISO/> Code W0091 Available Price €8.26
RFID Module with Card and Pendant It is compatible with almost any microcontroller, Arduino, PIC, AVR.It can be used in Access Control projects and Alarm projects. RFID Module with Card and Pendant features: - Supports Quick CRYPTO1 and MIFARE- Operating current: 13-26mA at 3.3V- Standby current: 10-13mA to 3.3V- Sleep-mode current: <80μA- Maximum current: 30mA- Frequency of operation: 13.56Mhz- Reading distance: 0 to 60mm- Communication protocol: SPI- Maximum SPI speed: 10Mbit / s- Maximum data rate: 10Mbit / s- Operating temperature: -20 to 80ºC- Humidity of operation: 5% -95% Code M0015 Available Price €2.31
NFC Card Type 2 NTAG215 RFID Dual Label 13.56 MHz NFC Card Type 2 NTAG215 RFID Dual Label 13.56 MHz features: - Standard: NFC Forum Type2 Tag Ntag215 - Protocol: ISO14443A - Memory: 540B (504B) EEPROM - Operating frequency: 13.56MHZ - Reading distance: 0-10CM - Communication speed: 106Kboud - Working temperature: -20ºC to 70ºC - Number of uses 100,000 times - Data retention: 10 years - Material: PVC - Dimensions 86 x 54 x 0.84 mm Code M0052 Available Price €1.64
NFC RFID Tag Card 13.56 MHz NFC RFID Tag Card 13.56 MHz can be used in Access Control projects and Alarm, Arduino, Raspberry PI, PIC, AVR projects. Code M0033 Available Price €0.82
RFID PN532 NFC Module NFC module for Educational STEAM Kit. Near field communication (NFC) is a set of standards for smartphones and similar devices to establish radio communication with each other by touching them together or bringing them into close proximity, usually no more than a few centimeters. Compatible with almost any microcontroller, Arduino, PIC, AVR. It can be used in Access Control projects and Alarm projects. RFID PN532 NFC Module features: - Based on the NXP PN532 chip, it can be used for non-contact communication of 13.56M.- Greater effective communication distance of 3 cm. Code W0092 Last items in stock Price €9.83
NFC RFID Keychain Tag 13.56 MHz NFC RFID Keychain Tag 13.56 MHz features: - 32 bit unique code - Protocol: ISO14443 - Compatible with NFC Mifare 1k - Memory: 1kB EEPROM - Operating frequency: 13.56MHZ - Communication speed: 106Kboud - Reading distance: 2.5-10CM - Reading time: 1-2MS - Working temperature: -20ºC to 85ºC - Number of uses 100,000 times - Data retention: 10 years - Material: ABS - Dimensions 40.5 x 32 x 4.2 mm Code M0030 Available Price €0.82
RFID PN532 NFC Module with Card and Pendant NFC module for Educational STEAM Kit. Near field communication (NFC) is a set of standards for smartphones and similar devices to establish radio communication with each other by touching them together or bringing them into close proximity, usually no more than a few centimeters. Compatible with almost any microcontroller, Arduino, PIC, AVR. It can be used in Access Control projects and Alarm projects. RFID PN532 NFC Module with Card and Pendant features: - Support i2C, SPI, High Speed UART - Support RFID reading and writing - Support P2P communication with peers - Support NFC with phone - Work in NFC Mode or RFID reader/writer Mode - RFID reader/writer supports: - 1k, 4k, Ultralight, and DesFire cards ISO/> Code W0091 Available Price €8.26
RFID Module with Card and Pendant It is compatible with almost any microcontroller, Arduino, PIC, AVR.It can be used in Access Control projects and Alarm projects. RFID Module with Card and Pendant features: - Supports Quick CRYPTO1 and MIFARE- Operating current: 13-26mA at 3.3V- Standby current: 10-13mA to 3.3V- Sleep-mode current: <80μA- Maximum current: 30mA- Frequency of operation: 13.56Mhz- Reading distance: 0 to 60mm- Communication protocol: SPI- Maximum SPI speed: 10Mbit / s- Maximum data rate: 10Mbit / s- Operating temperature: -20 to 80ºC- Humidity of operation: 5% -95% Code M0015 Available Price €2.31
NFC Card Type 2 NTAG215 RFID Dual Label 13.56 MHz NFC Card Type 2 NTAG215 RFID Dual Label 13.56 MHz features: - Standard: NFC Forum Type2 Tag Ntag215 - Protocol: ISO14443A - Memory: 540B (504B) EEPROM - Operating frequency: 13.56MHZ - Reading distance: 0-10CM - Communication speed: 106Kboud - Working temperature: -20ºC to 70ºC - Number of uses 100,000 times - Data retention: 10 years - Material: PVC - Dimensions 86 x 54 x 0.84 mm Code M0052 Available Price €1.64
NFC RFID Tag Card 13.56 MHz NFC RFID Tag Card 13.56 MHz can be used in Access Control projects and Alarm, Arduino, Raspberry PI, PIC, AVR projects. Code M0033 Available Price €0.82