L293D Quadruple Half-H Drivers STM L293D Quadruple Half-H Drivers STM features:-Continue 0.6A half-h driver STM Arduino Code T0014 Backorder Price €1.53
Resistor 1K Ohm 5% 0,25W 1/4W Resistor 1K Ohm 5% 0,25W 1/4W features:-1 unit - 1K Ohm-Type: Carbon film-Tolerance: ±5%-Power: 0.25W-Dimensions: 2x7mm Code D0076 Available Price €0.07
Infrared LED Flame Sensor 5mm module Led module infrared sensor for ArduinoDetector of the source of fire or flame, can detect a flame or wavelength 760 nm-1100 nmParticularly sensitive to the flame spectrum.This optical flame sensor is a device that detects the existence of combustion by the light emitted by it. Infrared LED Flame Sensor 5mm module features:- 4 Pins Output: - A0: analog output - D0: digital output - GND: ground connection - VCC: 5V module power- Range of light, Distance of 80 cm.- Angle detection of about 60 degrees,- This light can be detected by an optical sensor,- Can be captured by digital inputs and analog inputs of Arduino. Code S0133 Available Price €1.15
Wheels 30mm PP 360° Rotation for Cylindrical Use White plastic wheel with silver tone metal support.It allows a 360° rotation, provides a good resistance to rolling, wheel silently and without problems. Wheels 30mm PP 360° Rotation for Cylindrical Use features: - Main material: Polypropylene (PP), steel- Main color: White, silver tone- Total size: Total height: 45mm / 1.8 "- Wheel size: 30 x 13mm / 1.2 "x 0.5" (P * A)- Hole diameter for mounting: 4mm / 0.16 "- Space between holes: 28 x 22mm / 1.1 "x 0.9" (L * P)- Size of the top plate: 38 x 32mm / 1.5 "x 1.3" (L * P) Code H0128 Available Price €1.40
ESP8266 5V WiFi Relay Module AP Remote Control + STA You can easily control any device over the Internet through your phone, computer, etc. The module can handle 5 users at the same time, it can work in two modes: STA (client) and AP (access point). In AP mode, the module is connected via WIFI directly to your phone or computer (in open field can be up to 300 meters). In STA mode, the relay module is connected to the access point (router) that supplies the network. Wi-Fi in the room where the relays are located. In this case, the range mainly depends on the power of the access point antennas (routers). You should not turn off after the configuration is completed, as some of the parameters of the WIFI module cannot be saved when power is cut off. Code W0067 Available Price €7.84
Double Joystick Module 2 Axis XY PS2 Ideal for your arduino projects, but can also be used with other microcontrollers. Double Joystick Module 2 Axis XY PS2 features: - Two axes (XY) - Return to the center - Central push button - Connections: + 5Vcc / GND / VRx / VRy / SW - Dimensions: 4 x 2.6 x 3.2cm Code M0010 Available Regular price €2.07 -€0.31 Price €1.76
L9110 Fan Motor Propeller Module 5V The module for DIY Arduino hobbyMotor driver L9110 for Arduino, Smart Car, RoboticsSmall magnet electric motor for direct current (DC) L9110 Fan Motor Propeller Module 5V features: - Operating voltage: 5V- PCB dimension: 3.5 x 2.6cm- Double red propeller- Blade length 75mm- Weight: 6 g- Quantity: 1x DC motor 1x double helix Code M0132 Available Regular price €2.44 -€0.50 Price €1.94
BMP280 Temperature Barometric Pressure Sensor Module/SPI This module includes the BMP280 component that converts atmospheric pressure, temperature and humidity with high precision into a digital signal.The equipment uses the two I2C and SPI interfaces. The very good measurements made by the BMP280 allows the module to be used as an altimeter.Its 5-pin straight connector allows easy connection to other electronic boards. BMP280 Temperature Barometric Pressure Sensor Module/SPI features: - Interfaces: -I2C (up to 3.4 MHz) -SPI (up to 10 MHz)- Supply voltage: 1.8-5VDC- Module operating range: - Temperature: -40ºC to + 85ºC0-100% - Pressure: 300-1100 hPa- Resolution of the measures: - Temperature: 0.01ºC Code M0134 Available Regular price €4.12 -€1.00 Price €3.12
Relay SPDT JQC-3FF 5VDC-1ZS Relay 5VDC SPDT 5VDC JQC-3FF for industrial applications, automation and process control and consumer electronics. Relay SPDT JQC-3FF 5VDC-1ZS features: - Coil voltage: 5 VDC,- Coil power: 360 mW,- Switching capability: - 10A @ 277 VAC - 12A @ 125 VAC- Operating time: between 5ms and 10ms,- Plastic sealed and flux proofed types available,- Environmental friendly product (RoHS compliant),- Working temperature: -40ºC to 70ºC,- Outline dimensions: 19.0 x 15.2 x 15.5 mm. Code RL020 Available Price €0.81
433MHz RF Wireless Receiver + Transmitter Transmitter and receiver kit for radio control and data transmission, compatible with Arduino. 433MHz RF Wireless Receiver + Transmitter features: Specifications of the emitter module: - Power supply: 3V ~ 12V - Working intensity: max = 40mA (at 12V), min = 9mA (at 3V) - AM ASK / OOK modulation - SAW filter - Working frequency: 315MHz-433.92MHz - Transmission power: 25mW (315MHz at 12V) - Range: 20 to 200 meters (different voltages can give different results) - Transfer speed: 4 kB / S - Dimensions: 19x 19x 7mm Receiver module specifications: - Power supply: 5.0VDC + 0.5V - Work intensity: 5.5mA (at 5.0VDC) - Work frequency: 315MHz-433.92MHz - Receiver sensitivity: -100dBm Code W0010 Available Price €0.90
Solid State Relay SSR-25 DA 12A DC-AC Output 24V-380VAC The DC-AC 12A solid state relay has a 3-32VDC input and a 24-380VAC output. It has a maximum load capacity of 12A. It has a long operating life and high reliability, a compact size. This relay switches very quickly. Solid State Relay SSR-25 DA 12A DC-AC Output 24V-380VAC Code RL018 Available Price €6.60
SD Card Module Reader The SD card reader module is a simple solution for transferring data to and from a standard SD card.The pinout is directly compatible with Arduino, but it can also be used with other microcontrollers.SD Card Module Reader features:- Supply voltage: 3.3V or 5V - Interface: SPI 3.3V- Dimensions: 30mm x 50mm x 12mm Code M0023 Available Price €0.82
Development Board Ra-02 LoRa SX1278 Ra-02 Module (433MHz) Long range NodeMcu module based on ESP8266 controller and programming in Lua language NodeMcu is equipped with 10 GPIO, PWM, I2C, 1-wire and ADC ESP8266-12E is an improved version of ESP8266-12 It works as a standard WiFi 802.11 b / g / n 2.4 GHz USB Communication - CP2102 Chip Characteristic: ESP 12E ESP8266 ESP12E NodeMcu Lua Wireless Development Board CP2102 WiFi features: - Supply voltage: 3.3V (LOGICAL LEVELS: 3.3V) - Supported protocols: 802.11 b / g / n - Network support: 2.4 GHz - Band: 2400 (MHz) - Wi-Fi Direct (P2p), Soft Access Point - Integrated TCP / IP stack - PLL, regulators and integrated power management units - Output power: 0 , 15 (W); + 19.5dBm in 802.11b mode Code W0108 Available Price €7.43
2km radius SI4463 433MHz RF Telemetry Arduino compatible A compact, low-power Bottom Effect System Transceiver. Transceiver based on the SI4463 Silicon Labs chip. Industry standard model. In full power operating conditions, open the communication distance up to 2000 km. Much more than the SI4432. Si4463 is a high performance 433 MHz transceiver. and low current consumption of the EZRadioPRO series, which includes a complete transmitter and receiver. Higher sensitivity -126dBm. The maximum output power of + 20dBm, support (G) FSK, 4 (G) FSK, (G) MSK, OOK and ASK modulation. The data rate in the range of 100bps ~ 1Mbps. Operating voltage of 1.8V ~ 3.6V. FCC approval / IC. 2km radius SI4463 433MHz RF Arduino Telemetry features: - Supply voltage: 1.8 ~ 3.6VDC Code W0077 Available Price €5.98
Passive Buzzer 5V The piezoelectric buzzer has a simple structure in which a ceramic piezoelectric disk is affixed to a vibrating plate. An alternative voltage applied to this element will cause a contraction or diametrical expansion of the element. This feature is used to fold a vibrating plate, which generates sounds. 2x Passive Buzzer 5V features: - Input voltage: 3V to 12V - Diameter: 12mm - Height: 7.5mm - Pin spacing: 6.5mm - Impedance: 16 Ohm - Working frequency: 2 to 5 KHz - Quantity: 1 unit Code M0011 Available Price €0.32
WS2812 RGB 5050 Smart Addressable 5V Arduino compatible LED WS2811 WS2812 RGB 5050 Smart Addressable 5V Arduino LED WS2811 features: - WS2812 are LEDs that have built-in logic, making it possible to vary the color of each LED individually - WS2812 includes an integrated inside each LED, which allows access to each pixel individually. For this reason, these types of LEDs are individually indexable. - They are based on the 5050 LED - 24-bit color control (8-bit PWM per channel) - 16.8 millions of colors per LED - One-wire communication - Power: max. 5 Vdc - Current: 18.5mA - Input and output terminals (data and power) Code P0102 Available Price €1.40
CNC Shield + UNO R3 CH340 +4x A4988 Stepstick 3D Printer kit for Arduino CNC Shield + UNO R3 CH340 +4x A4988 Stepstick 3D Printer Arduino kit features: - Content:* 1x UNO R3 CH340 Compatible with Arduino* 1x CNC Shield V3* 4x A4988 Drivers* 4x Heatsinks for A4988* Jumpers Code I0010 Last items in stock Regular price €14.74 -€0.74 Price €14.00
PAM8403 2x3W Digital Amplifier Channel Stereo PAM8403 2x3W Digital Amplifier Channel Stereo features: - Up to 3W in each channel- Chip: PAM8403- Power supply: 5V- Power: 2 outputs of 3 watts each- Measures: 21x18 mm- Suitable impedance speakers: 4 Ohm Code M0027 Available Price €1.56
Relay SPDT JQC-3FF 5VDC-1ZS Relay 5VDC SPDT 5VDC JQC-3FF for industrial applications, automation and process control and consumer electronics. Relay SPDT JQC-3FF 5VDC-1ZS features: - Coil voltage: 5 VDC,- Coil power: 360 mW,- Switching capability: - 10A @ 277 VAC - 12A @ 125 VAC- Operating time: between 5ms and 10ms,- Plastic sealed and flux proofed types available,- Environmental friendly product (RoHS compliant),- Working temperature: -40ºC to 70ºC,- Outline dimensions: 19.0 x 15.2 x 15.5 mm. Code RL020 Available Price €0.81
433MHz RF Wireless Receiver + Transmitter Transmitter and receiver kit for radio control and data transmission, compatible with Arduino. 433MHz RF Wireless Receiver + Transmitter features: Specifications of the emitter module: - Power supply: 3V ~ 12V - Working intensity: max = 40mA (at 12V), min = 9mA (at 3V) - AM ASK / OOK modulation - SAW filter - Working frequency: 315MHz-433.92MHz - Transmission power: 25mW (315MHz at 12V) - Range: 20 to 200 meters (different voltages can give different results) - Transfer speed: 4 kB / S - Dimensions: 19x 19x 7mm Receiver module specifications: - Power supply: 5.0VDC + 0.5V - Work intensity: 5.5mA (at 5.0VDC) - Work frequency: 315MHz-433.92MHz - Receiver sensitivity: -100dBm Code W0010 Available Price €0.90
Solid State Relay SSR-25 DA 12A DC-AC Output 24V-380VAC The DC-AC 12A solid state relay has a 3-32VDC input and a 24-380VAC output. It has a maximum load capacity of 12A. It has a long operating life and high reliability, a compact size. This relay switches very quickly. Solid State Relay SSR-25 DA 12A DC-AC Output 24V-380VAC Code RL018 Available Price €6.60
SD Card Module Reader The SD card reader module is a simple solution for transferring data to and from a standard SD card.The pinout is directly compatible with Arduino, but it can also be used with other microcontrollers.SD Card Module Reader features:- Supply voltage: 3.3V or 5V - Interface: SPI 3.3V- Dimensions: 30mm x 50mm x 12mm Code M0023 Available Price €0.82
Development Board Ra-02 LoRa SX1278 Ra-02 Module (433MHz) Long range NodeMcu module based on ESP8266 controller and programming in Lua language NodeMcu is equipped with 10 GPIO, PWM, I2C, 1-wire and ADC ESP8266-12E is an improved version of ESP8266-12 It works as a standard WiFi 802.11 b / g / n 2.4 GHz USB Communication - CP2102 Chip Characteristic: ESP 12E ESP8266 ESP12E NodeMcu Lua Wireless Development Board CP2102 WiFi features: - Supply voltage: 3.3V (LOGICAL LEVELS: 3.3V) - Supported protocols: 802.11 b / g / n - Network support: 2.4 GHz - Band: 2400 (MHz) - Wi-Fi Direct (P2p), Soft Access Point - Integrated TCP / IP stack - PLL, regulators and integrated power management units - Output power: 0 , 15 (W); + 19.5dBm in 802.11b mode Code W0108 Available Price €7.43
2km radius SI4463 433MHz RF Telemetry Arduino compatible A compact, low-power Bottom Effect System Transceiver. Transceiver based on the SI4463 Silicon Labs chip. Industry standard model. In full power operating conditions, open the communication distance up to 2000 km. Much more than the SI4432. Si4463 is a high performance 433 MHz transceiver. and low current consumption of the EZRadioPRO series, which includes a complete transmitter and receiver. Higher sensitivity -126dBm. The maximum output power of + 20dBm, support (G) FSK, 4 (G) FSK, (G) MSK, OOK and ASK modulation. The data rate in the range of 100bps ~ 1Mbps. Operating voltage of 1.8V ~ 3.6V. FCC approval / IC. 2km radius SI4463 433MHz RF Arduino Telemetry features: - Supply voltage: 1.8 ~ 3.6VDC Code W0077 Available Price €5.98
Passive Buzzer 5V The piezoelectric buzzer has a simple structure in which a ceramic piezoelectric disk is affixed to a vibrating plate. An alternative voltage applied to this element will cause a contraction or diametrical expansion of the element. This feature is used to fold a vibrating plate, which generates sounds. 2x Passive Buzzer 5V features: - Input voltage: 3V to 12V - Diameter: 12mm - Height: 7.5mm - Pin spacing: 6.5mm - Impedance: 16 Ohm - Working frequency: 2 to 5 KHz - Quantity: 1 unit Code M0011 Available Price €0.32
WS2812 RGB 5050 Smart Addressable 5V Arduino compatible LED WS2811 WS2812 RGB 5050 Smart Addressable 5V Arduino LED WS2811 features: - WS2812 are LEDs that have built-in logic, making it possible to vary the color of each LED individually - WS2812 includes an integrated inside each LED, which allows access to each pixel individually. For this reason, these types of LEDs are individually indexable. - They are based on the 5050 LED - 24-bit color control (8-bit PWM per channel) - 16.8 millions of colors per LED - One-wire communication - Power: max. 5 Vdc - Current: 18.5mA - Input and output terminals (data and power) Code P0102 Available Price €1.40
CNC Shield + UNO R3 CH340 +4x A4988 Stepstick 3D Printer kit for Arduino CNC Shield + UNO R3 CH340 +4x A4988 Stepstick 3D Printer Arduino kit features: - Content:* 1x UNO R3 CH340 Compatible with Arduino* 1x CNC Shield V3* 4x A4988 Drivers* 4x Heatsinks for A4988* Jumpers Code I0010 Last items in stock Regular price €14.74 -€0.74 Price €14.00
PAM8403 2x3W Digital Amplifier Channel Stereo PAM8403 2x3W Digital Amplifier Channel Stereo features: - Up to 3W in each channel- Chip: PAM8403- Power supply: 5V- Power: 2 outputs of 3 watts each- Measures: 21x18 mm- Suitable impedance speakers: 4 Ohm Code M0027 Available Price €1.56