GPS Module GY-GPS6MV2 NEO6MV2 EEPROM with Antenna

USB Cable for Arduino Type A-B features:
- Length: 50cm
- Color: Blue

IR Remote Control + IR Infrared Receiver VS1838 features:
- The test distance is about 5-8 meters, but practical application depends on environmental factors (such as diaphragm, glass , obstructions or other material blockage) - The CHQ1838 / HX1838 receiver receives the 38kHz signal
- Vcc supply: 3.3V-5V
- IN digital output to connect to the port Arduino I / O
- Remote measurements 85x 40x 5mm
- Includes battery
Useful links for Arduino / Raspberry programming and projects with Arduino boards / Raspberry:
Send / Receive information via IR
- Wiring of the IR Remote control + Infrared IR Receiver VS1838 with the UNO module
- Light a 3mm red LED by Infrared

- Bootloader Pin Header Compatible 100% ARDUINO
- Pro Mini Atmega328P 5v 16Mhz
- Miniaturized compatible version of Arduino Pro Mini
- It has an Atmega328P chip running at 16Mhz with a factory-loaded bootloader. It does not include pins so we can only solder the pins that we need
Characteristic:
- ATmega328P 16MHz chip with external quartz crystal
- Auto-reset - micro switch
- Integrated 5V regulator
- FLASH 32kB memory
- SRAM 1kB memory
- EEPROM 1Kb memory
- Analog input A0-A7
- 8 PWM channels
- External interruption
- TWI / I2C, UART, SPI interfaces
- Power and status LEDs
- Dimensions: 18x33mm
- Weight: 30 grams
Useful links for Arduino />

- It has an Atmega328P chip running at 16Mhz with a factory loaded bootloader - The Uno R3 module has all the connectors than the Arduino Uno R3 and is compatible with all Arduino shields Arduino compatible UNO R3 board features:
- Includes USB Cable - ATmega328P 16MHz chip with external quartz crystal
- Microprocessor: ATmega328
- Operating voltage: 5V
- Input voltage (recommended): 7-12V
- Input voltage (limits): 6-20V
- Clock speed: 16 MHz
- Digital I / O Pins: 14
- Analog input pins: 6
- DC current per I / O Pin: 40 mA
- DC Current per Pin 3.3V: 50 mA
- Flash32 KB of which 0.5 KB are used by the bootloader - Atmega328
- SRAM 2 KB - Atmega328

NodeMcu module based on ESP8266 controller and programming in Lua language
NodeMcu is equipped with 10 GPIO, PWM, I2C, 1-wire and ADC
ESP8266-12E is an improved version of ESP8266-12
It works as a standard WiFi 802.11 b / g / n 2.4 GHz
USB Communication - CP2102 Chip
Characteristic:
ESP 12E ESP8266 ESP12E NodeMcu Lua Wireless Development Board CP2102 WiFi features:

- Supply voltage: 3.3V (LOGICAL LEVELS: 3.3V)
- Supported protocols: 802.11 b / g / n
- Network support: 2.4 GHz
- Band: 2400 (MHz) - Wi-Fi Direct (P2p), Soft Access Point
- Integrated TCP / IP stack
- PLL, regulators and integrated power management units
- Output power: 0 , 15 (W); + 19.5dBm in 802.11b mode

It can be used to control the microprocessor of the Arduino AVR PIC system and others, or as a digital potentiometer rotating the rotary encoder can be counted in positive and negative, depending on the direction of rotation; with the button of the rotary encoder can be reset to its initial state, which starts counting from 0.

1 Channel Relay Module DC 5V 10A Low/High Trigger for Arduino features:
- Channel: 1 (protected with Optocoupler)
- Supply voltage: 5V
- Output Current: 10A
- Relay activation current: 15mA ~ 20mA
- Insulation: Yes
- Trigger signal type jumper (low / high)
- LED indicator
- Dimensions: 30x 54mm
- Has a jumper that allows to choose type of trigger signal (low / high)
- This module can be controlled directly by the microcontroller (Arduino, 8051, AVR, PIC, DSP, ARM, ARM, MSP430, TTL)

Lot of 65 Male-Male jumper cables. Characteristic: -No soldering required
-You can easily modify or revise the circuits
-Quantity: 65 cables of different lengths and colors
-Cable lengths: 120mm, 150mm, 200mm, 240mm