Arduino Modules

NodeMcu module based on ESP8266 controller and programming in Lua language.
NodeMcu is equipped with 10 GPIO, PWM, I2C, 1-wire and ADC.
ESP8266-12E is an improved version of ESP8266-12.
It works as a standard WiFi 802.11 b / g / n 2.4 GHz.
USB communication - the CH340 chip. Characteristics of ESP 12E:
- Supply voltage: 3.3V (LOGICAL LEVELS: 3.3V)
- Supported protocols: 802.11 b / g / n
- Network support: 2.4 GHz
- Band: 2400 (MHz)
- Wi-Fi Direct (P2p), Soft Access Point
- TCP Stack / Integrated IP
- PLLs, Regulators and Integrated Power Management Units
- Output Power: 0.15 (W); + 19.5dBm in 802.11b mode

DS3231 Precision RTC Real Time Clock Module AVR ARM features:
- Can be used in projects of Arduino, Raspberry Pi, PIC, AVR
- Function compatible with the DS 3231
- Power supply voltage: +2.3 V to +5.5 V
- Temperature range: -40 ° C to + 85 ° C
- Low energy consumption
- Full clock calendar functions that include seconds, minutes, hours, date, month and year and valid until leap year compensation
- Two alarm calendar
- Interface: I2C

The piezoelectric buzzer has a simple structure in which a ceramic piezoelectric disk is affixed to a vibrating plate. An alternative voltage applied to this element will cause a contraction or diametrical expansion of the element. This feature is used to fold a vibrating plate, which generates sounds. 2x Passive Buzzer 5V features:

- Input voltage: 3V to 12V
- Diameter: 12mm
- Height: 7.5mm
- Pin spacing: 6.5mm
- Impedance: 16 Ohm
- Working frequency: 2 to 5 KHz
- Quantity: 1 unit

- This module includes PA preamplifier and LNA (Low-noise amplifier)
- Comes with the SMA antenna for 2.4GHz (2dB)
- Outdoor - transmission up to 250kbps and a distance of up to 1 kilometer
- Works at 2.4GHz frequencies (free frequency) and is ideal for telemetry projects, robots, peripherals control, video game control applications, remote temperature sensors, pressure, alarms, etc ... NRF24L01 + Wireless Antenna Transceiver 2.4 GHz 1Km PA LNA features:
* Based on chip NRF24L01 +
* Free band: 2.4GHz ISM
* Speed: 250kbps, 1Mbps, 2Mbps
* Work current
- Reception: 45 mA
- Transmission: 115 mA (4.2uA -sleep mode)
* Receiving sensitivity:
-104dB 250kbps
- 95dB 1Mbps
- 92dB 2Mbps
* SPI interface

Camera module for Arduino, Raspberry Pi 2 and Pi 3, B and B +. VGA camera 640x480 OV7670 B 0.3MPx 30fps Cmos features:
> - Input voltage 2.5V-3V
- Operating power 60mW / 15fps VGA YUV
- Resolution VGA 640x480 pixels (30fps)
- Maximum frame rate 30fps VGA
- Flicker 50Hz / 60Hz automatic detection
- Lens size 1/6 "
- Angle of view 25 °
- Sensitivity 1.3V / (lux- seg)
- SCCB (Serial Camera Control Bus) interface
- Output format · 8 Bits
- YUV / YCbCr 4: 2: 2
- RGB 565/555/444
- GRB 4: 2: 2
- RAW RGB data
- High sensitivity Light operation
- Automatic adjustment
- Color level saturation - Edge enhancement
- Noise level

It can be used to control the microprocessor of the Arduino AVR PIC system and others, or as a digital potentiometer rotating the rotary encoder can be counted in positive and negative, depending on the direction of rotation; with the button of the rotary encoder can be reset to its initial state, which starts counting from 0.

The bluetooth HC-05 module is one of the best options for projects where you need wireless communications.
The transceiver module (transmission / reception) allows bluetooth wireless connections as master or slave, works transparently as if making a wired RS-232 TTL serial connection. Arduino Wireless Module HC-05 HC05 Bluetooth features:
- CSR BC417 Chipset
- Power: 3.3.
- Bluetooth version V2.0 + EDR
- Frequency: 2.4GHz ISM band
- Modulation: GFSK
- Approximate range: 10m
- Security: Authentication and encryption
- Speed- & gt; Asynchronous: 2.1Mbps (Max) / 160 kbps; Synchronous: 1Mbps / 1Mbps
- Supports AT commands for configuration through a serial port
temperature: -20 ºC to +75 ºC

Module for Arduino, Raspberry Pi 2 and Pi 3, B and B +.
The display module 4-digit LED with TM1637.
The unit can be controlled with just two DIO and CLK control lines.
TM1637 4-Digit Digital Display Module features:

- 3V-5V supply voltage
- Current consumption 250 mA
- 7-segment display 4 digits common anode
- Digit size: 0.36 inches
- Dimensions: 42x24x11mm

Ideal for projects with ARDUINO you can use it with PIC, AVR, STM32.
Provides seconds, minutes, time and date, calendar up to the year 2100.
DS1302 Real Time Clock RTC Module AVR ARM PIC features:
- Chip: DS1302
- Power supply: 2V-5V
- Operating current: <2mA
- Dimensions: 44 x23 x 8mm
- Battery not included in this sale
- Connect the RTC to your Arduino
VCC -> Arduino + 3.3V
GND -> Arduino Gnd
CLK -> (SCLK_PIN)
DAT -> (IO_PIN)
RST -> (CE_PIN)

Camera module for Arduino, Raspberry Pi 2 and Pi 3, B and B +.
AL422B Video buffer consists of 3M-bits of DRAM, and it is configured as 393.216 x 8 bit FIFO (First In First Out). The interface is very easy to use because all operations are controlled by the internal DRAM memory controller. VGA Camera 640x480 FIFO AL422 Buffer OV7670 30fps features:
- Input voltage: 2.5V-3V
- Controller: AL422B FIFO buffer
- Operating power: 60mW / 15fps VGA YUV
- VGA resolution: 640x480 pixels (30fps),
- Maximum frame rate: 30fps VGA
- Flicker: 50Hz / 60Hz auto detection
- Lens size: 1/6 "
- Angle of view: 25 ° - Sensitivity: 1.3V / (lux- sec)
- SCCB (Serial Camera Control Bus) interface
- Output format: 8 Bits
- YUV />

Transceiver 1km SI4432 433MHz Wireless Transmitter Telemetry features:
- Transceiver based on the SI4432 Silicon Labs chip
- Ultrathin ultra small (16.5 × 17 mm)
- Good harmonics: easy for FCC / CE certification
- Penetration capacity (measured through 8 floors)
- Frequency range: 433.92MHz
- Sensitivity down to -121 dBm
- Maximum output power: 20dBm
- Data transfer rate: 0.123-256 kbps
- FSK, GFSK and OOK modulation
- Power supply: 1.8-3.6 V
- Ultra low power shutdown mode
- Digital indication of received signal strength (RSSI)
- Time to wake up
- Bidirectional antenna switch control and automatic adjustment
- Configurable packet structure
- Preamble detection

Transceiver based on the SI4432 Silicon Labs chip
Industry standard model
Capacitive components manufactured by Murata with 10ppm high precision glass
Outdoors - a distance of up to 1.5 km 1.5km radius SI4432 433MHz RF Telemetry features:
- Supply voltage: 1.8 ~ 3.6VDC
(Note: a voltage higher than 3.6 V will cause permanent damage to the module)
- Communication level: 0.7VDC ~ 3.6V (VCC refers to the module supply voltage)
- Working frequency: 425M ~ 525MHz (via software setting, the module uses 30M glass)
- Measured distance: 1500m (clear and open, maximum power, height 1.5m, air speed 1k)
- Transmission power: up to 20dBm (about 100mW)
- Air rate: 0.123k ~ 256Kbps (software adjustable, low airspeed recommended)

Shield Ethernet for Arduino boards and compatible based on the Wiznet W5100 chip.
Provides an easy way to connect your module to the local network now internet.
Compatible with the official Arduino Ethernet library.
With this shield you can build a web server.
It can be used as a server or as a client.
It has support for a microSD that can be used to store files for distribution on the network. Ethernet Shield W5100 Web Server features:
- Controller: Wiznet W5100
- Supports protocols TCP and UDP
- Supports up to 4 simultaneous connections
- Compatible with all Arduino versions: UNO, mega 1280/2560
- Dimensions: 74 x 54 x 25mm

A compact, low-power Bottom Effect System Transceiver.
Transceiver based on the SI4463 Silicon Labs chip.
Industry standard model.
In full power operating conditions, open the communication distance up to 2000 km.
Much more than the SI4432.
Si4463 is a high performance 433 MHz transceiver. and low current consumption of the EZRadioPRO series, which includes a complete transmitter and receiver.
Higher sensitivity -126dBm.
The maximum output power of + 20dBm, support (G) FSK, 4 (G) FSK, (G) MSK, OOK and ASK modulation.
The data rate in the range of 100bps ~ 1Mbps.
Operating voltage of 1.8V ~ 3.6V.
FCC approval / IC. 2km radius SI4463 433MHz RF Arduino Telemetry features:
- Supply voltage: 1.8 ~ 3.6VDC

Characteristic: - Operating voltage: 3-6V
- Max flow: 80-120 l / h
- Maximum pumping height: 40-110cm
- Continuous working time of 500 hours
- Cable length: 20cm
- Inside outlet diameter: 5 mm
- Outside outlet diameter: 7.5 mm - Dimensions: 45mm x 23mm x 30mm

SIM808 GPRS GSM GPS Bluetooth SIM Quadband features:
- SIM card SIM808 GPRS GSM GPS Bluetooth SIM
- Supply voltage range: 3.4-4.4V
- Four bands GSM 850/900/1800 / 1900MHz
- GPRS multi-slot class 12/10
- GPRS mobile station class B
- According to GSM phase 2/2 +
- Class 4 (2 W at 850/900 MHz)
- Class 1 (1W at 1800 / 1900MHz)
- Control by AT commands (3GPP TS 27.007.27.005 and enhanced AT Commands from SIM Com)
- Operating temperature: -40 to + 85 ° C
- PCB dimension: 38x38mm
- GPS sensitivity
- Tracking: -165dBm Cold start Sensitivity
- Cold start: -147dBm
- Time to first solution
- Cold start: 30 s
- Start to warm up: 28s
- Already hot: 1s - Accuracy

TPA3118 1X60W PBTL Channel Only Amplifier features:
- Chip: TPA3118
- Power supply: DC 8V ~ 24V
- Channel type: Single channel
- Output power: 1 x 60 W.
- Matching output: 4 ~ 8 Ohm
- Mono PBTL mode
- Size (LxWxH): 46 x 35 x 13 mm

Shield Li-Po Battery for WeMos D1 Mini ESP826 features:
Connect the lithium battery to this shield to supply power for the entire D1 mini system.
When the battery is depleted, it is not necessary disconnect the battery, just use the usb port to charge directly. - Charging voltage: max: 10V, recommend: 5V
- Charging current: max: 1A
- Voltage lithium battery: 3.3-4.2V
- Boost power supply: 5V (max: 1 A)
- LED color: red for charging, green for fully charged
- Ports:
* Micro USB - Charging port (normal 5V)
* Connect to the lithium battery (normal 3.3-4.2V)
* J1 - setting the maximum charging current, 0.5 A or 1A

This module can be controlled directly by the microcontroller (Arduino, 8051, AVR, PIC, DSP, ARM, ARM, MSP430, TTL, PLC output).
16 Channel Relay Module 12V 10A AVR features:
- Channels: 16 (independent protected with Optocouplers)
- Supply voltage: 12V
- Output Current: 10A
- Relay activation current: 3mA
- Insulation: Yes
- Low shot: 0-2V
- LED indicator: For each channel
- Dimensions: 18x 9x 2cm

SIM800L GPRS GSM SIM Board Quadband features:
Package includes:
- SIM800L module,
- 2x pin headers,
- Spring antenna,
- 3G PCB antenna - 15cm cable.
- Supported SIM format: Micro SIM.

The Bluetooth HC-06 module is one of the best options for projects where you need wireless communications. Arduino Wireless Module HC-06 HC06 features:
- CSR BC417 Chipset
- Power: 3.3V
- Bluetooth version V2.0 + EDR
- Frequency: 2.4GHz band ISM
- Modulation: GFSK
- Range approx. 10m
- Security: Authentication and encryption.
- Speed- & gt; Asynchronous: 2.1Mbps (Max) / 160 kbps; Synchronous: 1Mbps / 1Mbps
- Supports AT commands for configuration through a serial port
- Working temperature: -20 ºC to +75 ºC - Working current - pairing: 80 mA
- Transmission: 8mA
- Size: 28 x 12mm

2 Channel Relay Module 5V 10A for Arduino features:
- 5V relay module with 2 optocoupled channels
- This module can be controlled directly by the microcontroller (Arduino, 8051, AVR, PIC, DSP, ARM, ARM, MSP430, TTL)
- Channels: 2 (independent protected with Optocouplers)
- Supply voltage: 5V
- Output Current: 10A
- Relay activation current: 15mA ~ 20mA
- Insulation: Yes
- LED indicator: For each channel
- Dimensions: 40x 50mm

It is compatible with almost any microcontroller, Arduino, PIC, AVR.
It can be used in Access Control projects and Alarm projects. RFID Module with Card and Pendant features:
- Supports Quick CRYPTO1 and MIFARE
- Operating current: 13-26mA at 3.3V
- Standby current: 10-13mA to 3.3V
- Sleep-mode current: <80μA
- Maximum current: 30mA
- Frequency of operation: 13.56Mhz
- Reading distance: 0 to 60mm
- Communication protocol: SPI
- Maximum SPI speed: 10Mbit / s
- Maximum data rate: 10Mbit / s
- Operating temperature: -20 to 80ºC
- Humidity of operation: 5% -95%

The network module communicates with the Arduino type board through the SPI protocol ideal for projects with ARDUINO, PIC, AVR, STM32. ENC28J60 Ethernet LAN Network Module for Arduino AVR LPC STM3 features:
- Chip ENC28J60 Microchip
- Module: 10Base-T
- 3.3V power
- SPI interface
- 25Mhz speed
- LED status LED
- Hanrun network transformer
- Network Interface board HR911105A
- Operating temperature: -40ºC to + 85ºC
- Dimensions: 55x 35x 16 mm

WIFI transceiver based on the ESP8266 controller.
It has a microcontroller and 2 GPIO pins to be able to operate autonomously without the need for an external microcontroller. Characteristic: - Voltage of power: 3.3V
- Supported protocols: 802.11 b / g / n
- Network support: 2.4 GHz
- Band: 2400 (MHz)
- Wi-Fi Direct (P2p), Soft Access Point
- Integrated TCP / IP stack
- PLL, regulators and integrated power management units
- Output power: 0.15 (W); + 19.5dBm in 802.11b mode
- Consumption in low power mode:

5V Relay Module with 8 opto-coupled channels.
This module can be directly controlled by the microcontroller ( Arduino, 8051, AVR, PIC, DSP, ARM, ARM, MSP430, TTL).
8 Channel Arduino 5V 10A Relay Module features:

- Channels: 8 (independent protected with Optocouplers)
- Supply Voltage: 5V
- Output Current: 10A
- Relay activation current: 15mA ~ 20mA
- Isolation: Yes
- LED indicator: For each channel
- Dimensions: 54x 135mm

Led Matrix 8x8 MAX7219 Soldier features:
- MAX7219 controller module with 8x8 led matrix + cables
- 8X8 LED matrix controlled by MAX7219 chip
- Led 3mm red color
- SPI communication
- Voltage: 4.7 - 5.3V DC
- Interfaces to manage multiple modules in cascade
- Matrix dimensions: 32mm x 32mm x 8mm
- PCB dimensions: 32mm x 50mm

TDA2030A 1X18W Audio Amplifier features:
- Chip: TDA2030A
- Power supply: DC 6V ~ 12V
- Channel type: Single channel - Output power: 1 x 18 W
- Output output: 4 ~ 8 Ohm
- Mono mode
- Size (LxWxH): 31.6 x 23.5 mm

NFC RFID Keychain Tag 13.56 MHz features:
- 32 bit unique code
- Protocol: ISO14443
- Compatible with NFC Mifare 1k
- Memory: 1kB EEPROM
- Operating frequency: 13.56MHZ
- Communication speed: 106Kboud
- Reading distance: 2.5-10CM
- Reading time: 1-2MS
- Working temperature: -20ºC to 85ºC
- Number of uses 100,000 times
- Data retention: 10 years
- Material: ABS
- Dimensions 40.5 x 32 x 4.2 mm

NFC RFID Tag Card 13.56 MHz can be used in Access Control projects and Alarm, Arduino, Raspberry PI, PIC, AVR projects.

Characteristic: - Quiescent current: 50 mA (without load)
- Efficiency: 90%
- Nominal output power max.: 2 x 100W
- Frequency response: 20Hz to 20KHz
- Operating voltage: DC20V to DC34V
- Recommended supply voltage: DC32V
- Speaker parameters: 6 Ohm , 8 Ohm
- PCB board size: 87 × 72 mm
- Package includes cable

HC-06 Bluetooth transceiver module with base.
The bluetooth module HC-06 is one of the best options for projects, in which you need wireless communications.
The transceiver module allows bluetooth wireless connections as a slave, ready to listen for connection requests.
Bluetooth Transceiver Module HC-06 Wireless features:
- Chipset CSR BC417
- 3.5V - 5V power
- Bluetooth version V2.0 + EDR
- Frequency: 2.4GHz ISM band
- Modulation: GFSK
- Reach approx. 10m
- Security: Authentication and encryption.
- Speed-> Asynchronous: 2.1Mbps (Max) / 160 kbps; Synchronous: 1Mbps / 1Mbps
- Supports AT commands for configuration through a serial port
- Working temperature: -20ºC to + 75ºC
- Working current - pairing: 80 mA

USB DC 5V Bluetooth Audio features:
- You can connect it with your smartphone
- Power: DC 5V micro USB
- Speaker: 4 ~ 8 Ohm - Audio Jack: 3.5mm
- SD card: support MP3 / WMA / WAV / FLAC format
- The transmission distance could be up to 10m
- Size: 50 x 40 mm

- WIFI module based on the ESP8266 controller
- ESP8266-12F is an improved version of ESP8266-12E
- It works as a standard WiFi 802.11 b / g / n 2.4 GHz. It is equipped with 22 outputs (pitch 2 mm) of which 11 are GPIO, ADC 1 and SPI. A LED and a PCB antenna have been incorporated
ESP-12F ESP8266 12F WiFi Board Module features:
- Supply voltage: 3.3V (LOGICAL LEVELS: 3.3V)
- Supported protocols: 802.11 b / g / n
- Network support: 2.4 GHz
- Band: 2400 (MHz)
- Wi-Fi Direct (P2p), Soft Access Point
- Integrated TCP / IP Stack.
- PLL, regulators and integrated energy management units
- Output power: 0.15 (W); + 19.5dBm in 802.11b mode
- Consumption in low energy mode: <10 uA
- Integrated 32-bit processor

PAM8403 2x3W Digital Amplifier Channel Stereo features:
- Up to 3W in each channel
- Chip: PAM8403
- Power supply: 5V
- Power: 2 outputs of 3 watts each
- Measures: 21x18 mm
- Suitable impedance speakers: 4 Ohm

- HC-05 Bluetooth transceiver module with base
- The bluetooth module HC-05 is one of the best options for projects where you need wireless communications.
- The transceiver module (transmission / reception) allows bluetooth wireless connections like master or slave, works in a transparent way as if we made a RS-232 TTL serial connection with cable.
Bluetooth Transceiver Module HC-05 Wireless features:
- Chipset CSR BC417
- 3.6 to 6 Vdc power supply
- Bluetooth version V2.0 + EDR
- Frequency: 2.4GHz ISM band
- Modulation: GFSK
- Reach approx. 10m
- Security: Authentication and encryption.
- Speed-> Asynchronous: 2.1Mbps (Max) / 160 kbps; Synchronous: 1Mbps / 1Mbps

Edup Mini Dongle WiFi USB For pcDuino 3 Nano Raspberry Pi features:
- Interface type: USB
- Supports IEEE 802.11e draft 802.11n
- Supports USB 2.0, compatible with USB 1.1 and 1.2
- Support systems:
- Win2k / XP / Vista / Win7 / Win8.1 / Win10 / Mac / Linux
- Operating distance: 91 meters indoors, 275 meters in open space
- Transfer rate: 150Mbps (downlink) and 150Mbps (uplink)
- Works with old Wireless-G and Wireless-B networks
- WEP and WPA encryption - 64-bit / 128-bit WEP (Wired Equivalent Privacy), TKIP, AES 2,400GHz ISM
- Frequency range: 2.4 to 2.4835 GHz
- Operating channels: 13 - Support network protocol: CSMA / CA with acknowledgment
- Transmission mode: DSSS