List of products by brand Sparkfun

This little board is great for any type of prototyping - enables troubleshooting and debugging of any board with voltage from 0 to 5.5V. The  board interprets the commands and sends them further via a proper protocol (ranging from UART through I2C up to HDD44780 LCD). The Pirate lets analyze as well the data sent back from the device to the computer terminal effectively allowing to decipher potential errors. The bootloader installed on the board enables the quick and easy update of firmware and changing the functionality of the board.

This board features PIC24FJ64 and FT232RL USB-to-serial chip enabling swift communication over the mini-B USB port. On the other end of the board 2x5 pin header is placed with detailed descriptions of each pin.

The Circuit Scribe conductive ink pen, with its simple design, is perfect for this, allowing you to draw circuits instead of soldering or connecting them to a test board.  

This SparkFun CO2, humidity and temperature sensor incorporates Sensirion's new generation of SCD40 photoacoustic CO2 sensors for highly accurate environmental readings. The sensor is capable of detecting concentrations from 0 to 40000 ppm with high precision above 400-2000 ppm ±(50 ppm+5%). The SCD40 has an integrated CMos® temperature and humidity sensor for greater precision.

25ft (7.62m) reel of black Flexible Jumper Wire for electronics prototyping, soldering wire or any project where you need flexible wire. 22AWG (approx. 0.34mm2) cross-section.

25ft (7.62m) reel of red Flexible Jumper Wire for electronics prototyping, soldering wire or any project where you need flexible wire. 22AWG (approx. 0.34mm2) cross-section.

25ft (7.62m) reels of 6-colour Strandedjumper wire for electronics prototyping and breadboarding. 22AWG cross section (approx. 0.34mm2)

25ft (7.62m) reel of white patch cable for electronics prototyping and breadboarding. 22AWG (approx. 0.34mm2) cross section.

25ft (7.62m) reel of red patch cable for electronics prototyping and breadboarding. 22AWG (approx. 0.34mm2) cross section.

Pressure sensor sometimes called strain gauge. Load cell for measuring weights up to 50kg. The transducer measures the strain of the metal structure and converts it into a few mV.

This Cable Shield provides a 3.5mm connector where you can connect a three-electrode sensor cable, allowing you to test and use the MyoWare 2.0 muscle sensor without actually connecting it to your person.

This Shield provides a 3.5mm connector where you can connect a three-electrode sensor cable, allowing you to test and use the MyoWare muscle sensor without actually connecting it to your person.

This is the MyoWare Muscle Sensor Development Kit, an Arduino-powered electromyography (EMG) sensor kit that gives you the MyoWare, each MyoWare Shield and everything you need to connect them all together.

MyoWare Power Shield is designed to use two standard CR2032 coin cell batteries to power the MyoWare muscle sensor. These will be connected in parallel for extended capacity at a nominal 3.0V.

Simple breadboard for your MyoWare Muscle Sensor. You can use the provided area of the shield to solder in any custom circuit you can think of. This shield provides 8 x 15 solderable through holes on a standard 0.1" grid.

This is your simple three conductor sensor cable with electrode pad wires. These cables measure 24" long and feature a 3.5mm audio jack on one end with snap type receptacles for biomedical sensor pads.

It is the freshest serial LCD from SparkFun. Similarly to other SparkFun LCD screens it is put on single board with a microcontroller, however in contrast to the other screens in our offer (SP027 and SP028) it is based on PIC16F88 rather than ATmega328.

This little PCB piece is a great independent display addition to any project. Why independent? Well, it features an ATmega328P AVR on its back, making it a pretty much an UNO with a screen rather than a screen itself.

We have the same screen with a reverse color version, i.e. RGB on black with a reference of SP028

This little PCB piece is a great independent display addition to any project. Why independent? Well, it features an ATmega328P AVR on its back, making it a pretty much an UNO with a screen rather than a screen itself.

We have the same screen with a reverse color version, i.e. black on RGB with a reference of SP028

SparkFun Hamburger speaker is a high quality speaker in a small form and with even smaller price. You wouldn't believe you can get a quality product for less than 7€, right? Well, we couldn't believe that as well, but SparkFun makes that possible.

The SparkFun Weather Meter Kit is a set of basic mechanical and electronic components to build a weather station. With the SparkFun Arduino IoT Weather Station kit in sight, you can create your own weather station. The kit allows monitoring via the Arduino Cloud, an IoT platform.