Soldering Iron Cleaner with Brass Ball Holder

Soldering Station 48W features:
- Heating element for soldering iron: 48W
- Temperature: 150 ° C - 480 ° C
- Power: 220-240Vac
- Temperature controlled soldering station 48W,
- Adjust the desired temperature of the soldering iron with the adjustment knob,
- The color-coded areas are similar to the following temperatures:
- Yellow approx. 150 „ƒ
- Orange approx.> 150 to 270 „ƒ
- Red approx.> 270 to 480 „ƒ
- Wait about 2-3 minutes until the solder tip reaches the set temperature.

Resistor 220 Ohm 5% 0,25W 1/4W features:
-220 Ohm
-Type: Carbon film
-Tolerance: ±5%
-Power: 0.25W
-Dimensions: 2x7mm

Servos Tester features:
- 3-Channel Tester
- For Electronica Arduino

Encapsulated with water resistant stainless steel with sensor dimensions 5,5 * 50mm, cable length 100 cm.
DS18B20 Submersible Probe Sensor Temperature features:
- Based on the DS18B20 chip
- Supply voltage: 3 ~ 5.5V
- Consumption <5mA
- Measuring Range: -55 °C to 125 °C
- Accuracy: +/- 0,5ºC
- Outputs: - GND black
      - Red Vcc
      - Yellow digital output
- Inocidable steel
- Cable length: 1m

USB Cable A to Micro USB B Arduino Leonardo, Due features:
- Color: Blue or black
- Length: 50cm

SMD No Clean RF800 Liquid Soldering Flux 50ml Colophony Alcohol Base features:
Flux liquid alcohol-based for electronic welding.
Type of flux: rosin without halides, non-corrosive, No Clean, Lead Free, Non-conductive
Form: liquid
Capacity: 50ml
Content of solid bodies: 0 ... 5%
Viscosity (at 25 ° C): 794Mg / cm3 The flux cleans and prepares the surfaces and components to be welded, it facilitates the adherence and fluidity of the tin thanks to the rest of the components.
It cleans easily with alcohol.
It can be used with any tin. Security: - Do not inhale the vapors of the bottle or those that come off when welding.
- Keep the boat tightly closed and far away from the children.
- Use in ventilated spaces.

High grade in the absorption of tin for professionals.
Copper mesh roll for desoldering electronic components.
Desoldering Wire 1mm 1.0 features:
- Material: Copper
- Length: 1.5m
- Width: 1.0mm
- Desoldering Braid Solder Remover Wick 1mm / 1.5m
- Pure copper braid construction
- Quick removal welding
- Excellent thermal for a faster and safer desoldering

Totally new and of high quality.
Dissipate the heat of the computer by refrigerating it effectively.
It is used to attach passive dissipaters to graphic memories and chip plates and LED diodes.
Make sure to put the components correctly, once it has dried it will not be able to detach. Adhesive Thermal Paste Glue 10g CPU features:
  - Color white
- Surface drying time [25 ° C, min]: 2- 8
- Hardness: 45 -75
- Tensile strenght (Mpa): 2.0
- Elongation (%): 100
- Thermal Conductivity W / mk:> 1,0
- Volume Resistance (c-in / W): <2.0 x 10 * 15
- Dielectric strength (KV / mm): 20
- Dielectric Constant: 3.0
- Dielectric loss factor (60Hz): 0.003
- Operating temperature (max): 200 ° C