Welding Acid AG 35ml Welding Acid AG 35ml features:Prepared transparent liquid, acidic, corrosive.Prepares and facilitates welding on nickel-plated surfaces.Apply a small amount of the preparation on the element to be welded, and then wash it with water. CAUTION:Dangerous preparation, contains up to 35% phosphoric acid. In case of contact with skin or eyes, wash with plenty of water and consult a doctor. Keep closed and out of reach of children. It causes burns. Risk of serious eye damage. Code Q0056 Available Price €2.69
Relay Module DC 5V 10A 2 Channel Low/High Trigger Relay Module DC 5V 10A 2 Channel Low/High Trigger features:- Channels: 2 (independent protected with Optocouplers)- Supply voltage: 5V- Output Current: 10A- Relay activation current: 15mA ~ 20mA- Insulation: Yes- Trigger signal type jumper (low / high)- LED indicator: For each channel- Dimensions: 40x 50mm- It has a jumper that allows to choose type of trigger signal (low / high)- This module can be controlled directly by the microcontroller (Arduino, 8051, AVR, PIC, DSP, ARM, ARM, MSP430, TTL) Code RL002 Available Price €3.15
Potentiometer B5K Linear 5K OHM kΩ Characteristic: - Tolerance: +/- 20% - Power: 0.125W Code K0066 Available Price €0.99
Analogue to Digital Converter PCF8591T The PCF8591 is a low-power 8-bit single-chip, single-chip, 8-bit data acquisition device with four analog inputs, an analog output, and an I2C serial bus interface.Three address legs A0, A1 and A2 are used to program the hardware address, allowing the use of up to eight devices connected to the I2C bus without additional hardware.Address, control and data to and from the device are transferred in series through the two-way bidirectional I2C bus. Analogue to Digital Converter PCF8591T features: - Main chip: PCF85911- Operating voltage supply: 2.5 - 6 V- Low standby current- Serial input / output through the I2C bus- 3 hardware address pins A0, A1, A2- Sampling speed given by the I2C bus speed Code C0018 Available Price €2.50
Micro SD Card Reader/Recorder The micro SD card reader module is a simple solution for transferring data to and from a standard micro SD card.The pinout is directly compatible with Arduino, but it can also be used with other microcontrollers.Ideal for projects with ARDUINO, PIC, AVR, STM32.Micro SD Card Reader/Recorder features:- Supply voltage: 4.5V- 5.5V- Adjustable 3.3V built-in regulator for SPI pins- Consumption <200mA- Interface: SPI- Dimensions: 24mmx 42mm x 12mmSupports microSD cards (up to 2G) and micro SDHC (up to 32G) Code M0006 Available Price €2.49
Traffic light LED red yellow green 5V display module Arduino Red, yellow and green LED traffic light mini kit ideal for educational and beginner Arduino projects. Code M0231 Available Price €2.55
15x Electrolytic Capacitor 1uF 50V 105º C PIC for Arduino 15x Electrolytic Capacitor 1uF 50V 105º C PIC Arduino features:-Type: Electrolytic Capacitor-Assembly: intern-Value: 1uF-Maximum tension: 50V-Maximum temperature: 105º C-Dimensions: 5x11mm-Quantity: 15 units Code D0036 Available Price €0.09
Flux Welding Paste 20g Characteristic: - Solder paste according to DIN EN 29454-1 1.1.2.C. - Flux paste based on activity rosin medium. - Easy to weld: copper, silver, zinc and nickel plated. Flux residues after soldering do not cause corrosion of non-ferrous metals and can remain in the joints . Operating temperature up to 350 C. Code Q0025 Available Price €1.89
Magnifying LED Lamp Lens 4 Inch Magnifying LED Lamp Lens 4 Inch features: - Diopter: 3D + 12D- Lens size: 4 inch- Lens material: glass- Light source: 15pcs LED- Standard mount: table base Code H0144 Available Regular price €30.00 -5% Price €28.50
Soldering Tip Cleaning Ball It allows removing the solder residues from the tips.It cleans better and does not cause temperature drops like with sponges.You do not need extra water to clean the tip.Easy and effective cleaning at the tip.Soldering Tip Cleaning Ball features:- Dimensions: diameter 50mm Code H0010 Available Price €1.29
Flux Gel 10ml Based on RMA Colophony Flux Gel 10ml Based on RMA Colophony features: - Flux gel, RMA condensed rosin for non-halide welding, non-corrosive, No Clean, Lead Free, Non-conductive- Shape: gel- Capacity: 10ml- Plastic Packaging- SMT mounting time up to 36 hours- Retains stickiness at 72 hours- Good welding capacity on surfaces: Ag, Cu, Au, Zn, Cd, SnPb- Flux Gel, Soldering Paste, Grease, BGA / SMD / SMT Assembly and repairs Security: - Do not inhale vapors from the bottle or those that come off when welding- Keep out of reach of children- Use in ventilated spaces- Do not eat. Highly flammable toxic (contains alcohols). Rarely irritating to skin contact. Wash with plenty of water Code Q0047 Available Price €6.75
Liquid Flux for Alcohol-Based Rosin Welding 15ml Liquid Flux for Alcohol-Based Rosin Welding 15ml features: - Flux liquid alcohol-based for electronic welding- Type of flux: rosin without halides, non-corrosive, No Clean, Lead Free, Non-conductive- Liquid form- Capacity: 15ml- Content of solid bodies 0 ... 5%- Viscosity (temp. 25 ° C) 794Mg / cm3- The flux cleans and prepares the surfaces and components to be welded, facilitates the adhesion and fluidity of the tin thanks to the other components- Cleans easily with alcohol- Can be used with any tin Code Q0020 Available Price €1.95
Soldering PCB Holder 200x140mm Adjustable 360 Degrees Soldering PCB Holder 200x140mm Adjustable 360 Degrees features: - Support for welding, repair- Adjustable support 360 degrees- Tool for mobile repair- Circuit Board Repair Moviles- High quality- Weight: 0.7kg- Dimensions: Approx. 300x165x125mm Code H0050 Available Price €12.95
Soldering Iron Holder Soldering Iron Holder features: - Comes supplied with a special replaceable sponge, for use in cleaning the tip- Suitable for use with most welders- Dimensions of base: 84 x 130 mm- Weight: 0.2kg Code H0095 Available Price €3.99
Mini Holder Soldering Iron Stand Mini Holder Soldering Iron Stand features: - Dimensions: 65x 42mm Code H0009 Available Price €1.29
Helping Magnifying Hand Tool It is a very ideal tool when the third hand is required.Helping Magnifying Hand Tool features:- Magnifying glass diameter 60mm- Weight: 0.5kg- Dimensions: approx. 15 (26) x 17 x 7cm Code H0011 Available Price €7.95
Liquid Flux Alcohol Base TK83 100ml Liquid Flux Alcohol Base TK83 100ml Flux liquid alcohol based for electronic welding. Type of flux: rosinNo Clean, Lead Free, Non-conductive. Ideally suited for manual tinning to restore solderability. Solids content 24%. max. soldering temperature 280ºC. Code Q0115 Backorder Price €4.49
SMD No Clean RF800 Liquid Soldering Flux 50ml Colophony Alcohol Base SMD No Clean RF800 Liquid Soldering Flux 50ml Colophony Alcohol Base features: Flux liquid alcohol-based for electronic welding.Type of flux: rosin without halides, non-corrosive, No Clean, Lead Free, Non-conductiveForm: liquidCapacity: 50mlContent of solid bodies: 0 ... 5%Viscosity (at 25 ° C): 794Mg / cm3 The flux cleans and prepares the surfaces and components to be welded, it facilitates the adherence and fluidity of the tin thanks to the rest of the components.It cleans easily with alcohol.It can be used with any tin. Security: - Do not inhale the vapors of the bottle or those that come off when welding.- Keep the boat tightly closed and far away from the children.- Use in ventilated spaces. Code Q0013 Available Price €3.79
Magnifying LED Lamp Lens 4 Inch Magnifying LED Lamp Lens 4 Inch features: - Diopter: 3D + 12D- Lens size: 4 inch- Lens material: glass- Light source: 15pcs LED- Standard mount: table base Code H0144 Available Regular price €30.00 -5% Price €28.50
Soldering Tip Cleaning Ball It allows removing the solder residues from the tips.It cleans better and does not cause temperature drops like with sponges.You do not need extra water to clean the tip.Easy and effective cleaning at the tip.Soldering Tip Cleaning Ball features:- Dimensions: diameter 50mm Code H0010 Available Price €1.29
Flux Gel 10ml Based on RMA Colophony Flux Gel 10ml Based on RMA Colophony features: - Flux gel, RMA condensed rosin for non-halide welding, non-corrosive, No Clean, Lead Free, Non-conductive- Shape: gel- Capacity: 10ml- Plastic Packaging- SMT mounting time up to 36 hours- Retains stickiness at 72 hours- Good welding capacity on surfaces: Ag, Cu, Au, Zn, Cd, SnPb- Flux Gel, Soldering Paste, Grease, BGA / SMD / SMT Assembly and repairs Security: - Do not inhale vapors from the bottle or those that come off when welding- Keep out of reach of children- Use in ventilated spaces- Do not eat. Highly flammable toxic (contains alcohols). Rarely irritating to skin contact. Wash with plenty of water Code Q0047 Available Price €6.75
Liquid Flux for Alcohol-Based Rosin Welding 15ml Liquid Flux for Alcohol-Based Rosin Welding 15ml features: - Flux liquid alcohol-based for electronic welding- Type of flux: rosin without halides, non-corrosive, No Clean, Lead Free, Non-conductive- Liquid form- Capacity: 15ml- Content of solid bodies 0 ... 5%- Viscosity (temp. 25 ° C) 794Mg / cm3- The flux cleans and prepares the surfaces and components to be welded, facilitates the adhesion and fluidity of the tin thanks to the other components- Cleans easily with alcohol- Can be used with any tin Code Q0020 Available Price €1.95
Soldering PCB Holder 200x140mm Adjustable 360 Degrees Soldering PCB Holder 200x140mm Adjustable 360 Degrees features: - Support for welding, repair- Adjustable support 360 degrees- Tool for mobile repair- Circuit Board Repair Moviles- High quality- Weight: 0.7kg- Dimensions: Approx. 300x165x125mm Code H0050 Available Price €12.95
Soldering Iron Holder Soldering Iron Holder features: - Comes supplied with a special replaceable sponge, for use in cleaning the tip- Suitable for use with most welders- Dimensions of base: 84 x 130 mm- Weight: 0.2kg Code H0095 Available Price €3.99
Mini Holder Soldering Iron Stand Mini Holder Soldering Iron Stand features: - Dimensions: 65x 42mm Code H0009 Available Price €1.29
Helping Magnifying Hand Tool It is a very ideal tool when the third hand is required.Helping Magnifying Hand Tool features:- Magnifying glass diameter 60mm- Weight: 0.5kg- Dimensions: approx. 15 (26) x 17 x 7cm Code H0011 Available Price €7.95
Liquid Flux Alcohol Base TK83 100ml Liquid Flux Alcohol Base TK83 100ml Flux liquid alcohol based for electronic welding. Type of flux: rosinNo Clean, Lead Free, Non-conductive. Ideally suited for manual tinning to restore solderability. Solids content 24%. max. soldering temperature 280ºC. Code Q0115 Backorder Price €4.49
SMD No Clean RF800 Liquid Soldering Flux 50ml Colophony Alcohol Base SMD No Clean RF800 Liquid Soldering Flux 50ml Colophony Alcohol Base features: Flux liquid alcohol-based for electronic welding.Type of flux: rosin without halides, non-corrosive, No Clean, Lead Free, Non-conductiveForm: liquidCapacity: 50mlContent of solid bodies: 0 ... 5%Viscosity (at 25 ° C): 794Mg / cm3 The flux cleans and prepares the surfaces and components to be welded, it facilitates the adherence and fluidity of the tin thanks to the rest of the components.It cleans easily with alcohol.It can be used with any tin. Security: - Do not inhale the vapors of the bottle or those that come off when welding.- Keep the boat tightly closed and far away from the children.- Use in ventilated spaces. Code Q0013 Available Price €3.79