Soldering Acid AG 35ml

Silicone Thermal Conductive Paste 0.5g Heatsink 3D features:
It facilitates the transfer of heat between the electronic components and the radiator.
It's necessary for the correct operation of any type of temperature sensors.
Is characterized by a very good chemical resistance for oxidation, water solutions of acids, alkalis and salts, sulfur dioxide and ammonia. It has a very wide range of working temperatures.
-Density at 20°C: 2.58 G/cm3
-Points: 350°C
-Freezing point: -50°C
-Coefficient of refraction: 1.405,
- Specific temperature at 50°C: 0.243 Cal/g K
-Co-efficient global heat transfer at 0-150°C: 0.88 W/m K
-Constant dielectric at 100 Hz: 4.7 (± 0.1)
-Cross resistance: 5x10 to power 14 Ohm x cm

Potentiometer Cleaner - Spray 60ml features:
A special preparation for potentiometers, perfectly suited to remove any dirt deposited during the operation of the device, contains a special grease to reduce friction. It cleans waste contacts, also regenerates them.

Characteristic: - Solder paste according to DIN EN 29454-1 1.1.2.C.
- Flux paste based on activity rosin medium.
- Easy to weld: copper, silver, zinc and nickel plated. Flux residues after soldering do not cause corrosion of non-ferrous metals and can remain in the joints .
Operating temperature up to 350 C.

Anti-Adhesive No-Fat Dry Spray Based on PTFE 100ml. Dry, no-fat, anti-adhesive agent based on pure PTFE

AG Gold is a high quality thermal conductive paste. Due to its gold content, its thermal conductivity is 3 times higher than in the case of normal pasta.
This allows the processor to lower the processor temperature by approximately 6 degrees, even without changing the radiator. Pasta is the best alternative for overlockers.
Thermal conductivity:> 2.8 W / mK,

Flux Solder Paste in Tin Can 40g features:
- Welding paste according to DIN EN 29454-1 1.1.2.C
- Flux paste based on medium activity rosin
- Easy to solder: copper, silver plated, zinc and nickel Flux residues after welding do not cause corrosion of non-ferrous metals and may remain in the joints.
Operating temperature of up to 350 C.

Necessary for the protection of printed circuits.
PCB varnish of high quality for manufacturing, repair and maintenance.
Prevents the oxidation of printed circuit boards during intermediate storage. Insulating Varnish Spray 400ml features:
-A protective film, transparent.
-Protects soft metals for welding (eg copper, steel, lead, tin, brass) against corrosion, moisture, oxidation, dust, chemical contamination
-It maintains the welding, to carry out a subsequent welding it is not necessary to eliminate the
protective film
-PVB 16 is used, for example, in the storage of printed circuit boards and material that is going to be
soldier, such as welding terminals or conductors.
-Temperature of application: od -40 ° C + 60 ° C.

Epoxy resin is an encapsulating, two-component mixture. Cures at room temperature. Excellent electrical insulation and good adhesion to virtually all materials. Ideal for potting or filling gaps in heat-generating electronic components with metal enclosures or heat sinks. 

Graphite Grease- the product has excellent lubricating qualities and is provides an effective anticorrosive protection. The addition of graphite increases its resistance to burdens and the action of cold water. Application: car leaf springs etc.

The silicone paste provides insulation and protection against the weather. N Silicone Insulating Paste 3.5g features:
- The breaking voltage is ~ 30kV / mm.
- Preserves rubber, plastic
- A wide range of operating temperatures: -50 ° C to 200 ° C
- Very good resistance to chemical oxidation, aqueous solutions of acids, bases and sales, sulfur dioxide and ammonia. High quality - manufactured in EU