PCB Heated Bed MK3 Alu 3mm 12V 24V Reprap 3D Printer PCB Heated Bed MK3 Alu 3mm 12V 24V Reprap 3D Printer features: - Similar to MK2, can also be used with 12 volts or 24 volts - Measurements: 214 x 214 mm - 1 layer of 35μm (1 oz base) of copper Code I0091 Backorder Price €12.99
Magnifying LED Lamp Lens 5 Inch Magnifying LED Lamp Lens 5 Inch features: - 80 Leds, diopter 5D- Lens size: 5 inch- Lens material: glass- Light source: 80 pcs LED- Standard mount: table clamp Code H0143 Available Regular price €60.00 -5% Price €57.00
Transparent Box for W1209 DIY Transparent Box for W1209 DIY features: For W1209 Thermostat DC 12V temperature controller Code M0107 Available Price €2.69
W1209 12V DC Thermostat Digital Temperature Controller Switch W1209 12V DC Thermostat Digital Temperature Controller Switch features: - Model: W1209 - Supply voltage: DC 12V - Temperature control mode: ON / OFF - Temperature range: -50 -110 ° C - Resolution: 0.1 ° C range -9.9 ~ 99.9 ° C, above is 1 ° C - Measurement accuracy: 0.1 ° C - Refresh rate: 0.5 s - Temperature protection 0-110 ° C - Static current: ‰ ¤ 35mA, working current ‰ ¤ 65mA - Power of output: 10A relay - Sensor probe: NTC waterproof sensor (10K 0.5%) - Environmental requirements: -10 ~ 60 ° C Humidity 20% -85% - Dimensions: 48 x 40 mm Code M0102 Available Price €3.79
Fan 12V 2x 3D Printer Cables Fan 12V 2x 3D Printer Cables features: - Voltage: 12V - Consumption: 65mA - Speed: 3800rpm -5600rpm - Noise level: 25dB ± 10% - Screw diameter: 4.5mm - Service Life Time: 35000 hours - Operating temperature: -10 ° C to 65 ° C - Cable length: 11cm - Dimensions: 40mm x 40mm x 10mm Code I0026 Available Price €1.89
Ceramic alignment tool CD-20 The zirconium ceramic tip of the CD-200/201 combines the wear resistance of a metal tip with the non-conductive and non-inductive properties of the plastic.Ceramic alignment tool CD-20 features:- Length: 11.5 cm,- Screwdriver tip: flat,- Tip length: 2mm.- Suitable for: potentiometers, watchmaking, electronics components. Code H0150 Available Price €2.29
Extruder Kit MK8 Bowden Aluminium 1.75mm 3D Printer Creality Ender Extruder MK8 Bowden for Creality 3D Ender 3, CR-7, CR-8, CR-10, CR-10S, CR-10 S4 y CR-10 S5. Includes: MK8 extruder complete push system. Square part dimensions: 42x42mm. Part dimensions - handle L: 56x28mm Code I0183 Backorder Price €14.95
3x Silicone Thermal Conductive Paste 0.5g Heatsink 3D 3x Silicone Thermal Conductive Paste 0.5g Heatsink 3D features:It facilitates the transfer of heat between the electronic components and the radiator.It's necessary for the correct operation of any type of temperature sensors.Is characterized by a very good chemical resistance for oxidation, water solutions of acids, alkalis and salts, sulfur dioxide and ammonia. It has a very wide range of working temperatures.-Density at 20°C: 2.58 G/cm3-Points: 350°C-Freezing point: -50°C-Coefficient of refraction: 1.405,- Specific temperature at 50°C: 0.243 Cal/g K-Co-efficient global heat transfer at 0-150°C: 0.88 W/m K-Constant dielectric at 100 Hz: 4.7 (± 0.1)-Cross resistance: 5x10 to power 14 Ohm x cm Code Q0080 Available Price €0.95
LED Diode COB 10W Orange SMD COB LEDs are built as a matrix of LEDs, that is, a concentration of LEDs in a silicone coated tablet.The advantages of LED COB:- A luminous performance of up to 120 lumens / watt (twice as much as LED SMD)- The light intensity is greater without needing to concentrate so much the beam of light- Greater durability- Angle of opening up to 160ºC- Multidirectional lightMount LED diode on a good heatsink, add some fan, this is necessary because you have to "remove" the heat from the surface of the plate so that the LEDs last longer to place a little bit of thermal silicone in each of the placement centers the diodes.The thermal paste increases the thermal transfer between the diode and the metal plate used as a circuit. Code P0034 Available Price €2.83
LED Diode COB 10W 6000K White SMD COB LEDs are built as a matrix of LEDs, that is, a concentration of LEDs in a silicone coated tablet. The advantages of LED COB: - a light output of up to 120 lumens / watt (twice as much as LED SMD)- the light intensity is greater without the need to concentrate the beam of light- greater durability- opening angle of up to 160ºC- multidirectional light Mount LED diode on a good heatsink, add some fan, this is necessary because you have to "remove" the heat from the surface of the plate so that the LEDs last longer to place a little bit of thermal silicone in each of the placement centers. the diodes.The thermal paste increases the thermal transfer between the diode and the metal plate used as a circuit. Code P0145 Available Price €1.32
RGB LED Smart Strip WS2812B Black 5m 30LED/m IP65 WS2812B are LEDs that have built-in logic, making it possible to vary the color of each LED individually. WS2812B includes a integrated inside each LED, which allows each pixel to be accessed individually. For this reason, these types of LEDs are called individually indexable. They are based on the 5050 LED. RGB LED Strip WS2812B Black 5m 30LED/m IP65 features: - 30 individually indexable LEDs - - 24-bit color control (8-bit PWM per channel) - 16.8 million colored by LEDs - One-wire communication - Power: 5 V - Width: 11 mm - Thickness: 2.6 mm - Length: 5 meter - Consumption: 1.8A (all white) - Water resistant - With 3M adhesive - Input and output terminals (data and power) Code P0105 Backorder Price €39.95
LED 1W Green SMD Mount LED Diode on a good heatsink, a metal plate, add a fan, this is necessary because you have to "remove" the heat from the surface of the board so that the LEDs last longer to place a little bit of thermal silicone in each of the diode's placement centers. The thermal paste increases the thermal transfer between the diode and the metal plate used as a circuit. Important to keep in mind the diodes generate a lot of light intensity and very concentrated. Avoid looking directly at them once they are turned on and wear protective glasses when working with them. Characteristic: - 30mil chip - Voltage: 3.0-3.2V - Current: 300mA - Luminous flux: 70-80LM - Ã beam angle: 120 degrees - Color emission: green Code P0046 Available Price €0.98
LED Diode 1W Warm White SMD 130LM Mount LED Diode on a good heatsink, a metal plate, add some fan, this is necessary because you have to " remove "the heat from the surface of the plate so that the LEDs last longer to place a little bit of thermal silicone in each of the centers of placement of the diodes. The thermal paste increases the thermal transfer between the diode and the metal plate used as a circuit. Important to keep in mind the diodes generate a lot of light intensity and very concentrated. Avoid looking directly at them once they are turned on and wear protective glasses when working with them. Characteristic: - Chip 28x47mil - Voltage: 2.85-3.85V - Current: 350mA - Luminous flux: 120-130LM - Beam angle: 130 degrees Code P0151 Available Price €0.98
LED 3W Blue SMD Mount LED Diode on a good heatsink, a metal plate, add a fan, this is necessary because you have to "remove" the heat from the surface of the board so that the LEDs last longer to place a little bit of thermal silicone in each of the diode's placement centers. The thermal paste increases the thermal transfer between the diode and the metal plate used as a circuit. Important to keep in mind the diodes generate a lot of light intensity and very concentrated. Avoid looking directly at them once they are turned on and wear protective glasses when working with them. Characteristic: - Chip 28x47mil - Voltage: 3.1-4.1V - Current: 700mA - Luminous flux: 39-55LM - Ã beam angle: 120 degrees - Color emission: blue Code P0152 Available Price €1.59
WS2812B RGB LED Strip White 1m 30 LED/M IP65 WS2812B RGB LED Strip White 1m 30 LED/M IP65 features: - IP65 RGB Addressable Smart Arduino - RGB LED WS2812B S2812B are LEDs that have integrated logic, so it is possible to vary the color of each LED individually S2812B includes a built-in inside each LED, which allows each pixel to be accessed individually - For this reason, these types of LEDs are called individually indexable - They are based on the 5050 LED - 30 individually indexable LED diodes - 24-bit color control (8-bit PWM per channel) - 16.8 million colors by LED - One-wire communication - Power: 5 V idth: 11 mm - Thickness: 2.6 mm - Length: 1 meter - Consumption: 1.8A (all white) ater resistant Code P0103 Last items in stock Price €9.75
Aluminum Heat Sink 15x2cm LED 1W-3W Aluminum Heat Sink 15cm 2cm LED 1W 3W features:Aluminum heatsink for LED 1W-3W, Length: 15cm, Width: 2.0cm, Height: 0.6cm. Code P0051 Available Price €2.79
LED diode 1W White SMD 130LM Mount LED Diode on a good heatsink, a metal plate, add some fan, this is necessary because you have to " remove "the heat from the surface of the plate so that the LEDs last longer to place a little bit of thermal silicone in each of the centers of placement of the diodes. The thermal paste increases the thermal transfer between the diode and the metal plate used as a circuit. Important to keep in mind the diodes generate a lot of light intensity and very concentrated. Avoid looking directly at them once they are turned on and wear protective glasses when working with them. Characteristic: - Chip 28x47mil - Voltage: 3.0-3.2V - Current: 300mA - Luminous flux: 120-130LM - Beam angle: 130 degrees Code P0043 Available Price €0.98
LED Power Diode COB 10W 3000K White SMD COB LEDs are built as a matrix of LEDs, that is, a concentration of LEDs in a silicone coated tablet. The advantages of LED COB: - A light output of up to 120 lumens / watt (twice as much as LED SMD)- The light intensity is greater without concentrating the beam of light- Greater durability- Angle of opening up to 160ºC- Multidirectional light Mount LED diode on a good heatsink, add some fan, this is necessary because you have to "remove" the heat from the surface of the board so that the LEDs last longer.Place a little thermal silicone in each of the diode placement centers. Code P0148 Available Price €2.11
LED Diode COB 10W Orange SMD COB LEDs are built as a matrix of LEDs, that is, a concentration of LEDs in a silicone coated tablet.The advantages of LED COB:- A luminous performance of up to 120 lumens / watt (twice as much as LED SMD)- The light intensity is greater without needing to concentrate so much the beam of light- Greater durability- Angle of opening up to 160ºC- Multidirectional lightMount LED diode on a good heatsink, add some fan, this is necessary because you have to "remove" the heat from the surface of the plate so that the LEDs last longer to place a little bit of thermal silicone in each of the placement centers the diodes.The thermal paste increases the thermal transfer between the diode and the metal plate used as a circuit. Code P0034 Available Price €2.83
LED Diode COB 10W 6000K White SMD COB LEDs are built as a matrix of LEDs, that is, a concentration of LEDs in a silicone coated tablet. The advantages of LED COB: - a light output of up to 120 lumens / watt (twice as much as LED SMD)- the light intensity is greater without the need to concentrate the beam of light- greater durability- opening angle of up to 160ºC- multidirectional light Mount LED diode on a good heatsink, add some fan, this is necessary because you have to "remove" the heat from the surface of the plate so that the LEDs last longer to place a little bit of thermal silicone in each of the placement centers. the diodes.The thermal paste increases the thermal transfer between the diode and the metal plate used as a circuit. Code P0145 Available Price €1.32
RGB LED Smart Strip WS2812B Black 5m 30LED/m IP65 WS2812B are LEDs that have built-in logic, making it possible to vary the color of each LED individually. WS2812B includes a integrated inside each LED, which allows each pixel to be accessed individually. For this reason, these types of LEDs are called individually indexable. They are based on the 5050 LED. RGB LED Strip WS2812B Black 5m 30LED/m IP65 features: - 30 individually indexable LEDs - - 24-bit color control (8-bit PWM per channel) - 16.8 million colored by LEDs - One-wire communication - Power: 5 V - Width: 11 mm - Thickness: 2.6 mm - Length: 5 meter - Consumption: 1.8A (all white) - Water resistant - With 3M adhesive - Input and output terminals (data and power) Code P0105 Backorder Price €39.95
LED 1W Green SMD Mount LED Diode on a good heatsink, a metal plate, add a fan, this is necessary because you have to "remove" the heat from the surface of the board so that the LEDs last longer to place a little bit of thermal silicone in each of the diode's placement centers. The thermal paste increases the thermal transfer between the diode and the metal plate used as a circuit. Important to keep in mind the diodes generate a lot of light intensity and very concentrated. Avoid looking directly at them once they are turned on and wear protective glasses when working with them. Characteristic: - 30mil chip - Voltage: 3.0-3.2V - Current: 300mA - Luminous flux: 70-80LM - Ã beam angle: 120 degrees - Color emission: green Code P0046 Available Price €0.98
LED Diode 1W Warm White SMD 130LM Mount LED Diode on a good heatsink, a metal plate, add some fan, this is necessary because you have to " remove "the heat from the surface of the plate so that the LEDs last longer to place a little bit of thermal silicone in each of the centers of placement of the diodes. The thermal paste increases the thermal transfer between the diode and the metal plate used as a circuit. Important to keep in mind the diodes generate a lot of light intensity and very concentrated. Avoid looking directly at them once they are turned on and wear protective glasses when working with them. Characteristic: - Chip 28x47mil - Voltage: 2.85-3.85V - Current: 350mA - Luminous flux: 120-130LM - Beam angle: 130 degrees Code P0151 Available Price €0.98
LED 3W Blue SMD Mount LED Diode on a good heatsink, a metal plate, add a fan, this is necessary because you have to "remove" the heat from the surface of the board so that the LEDs last longer to place a little bit of thermal silicone in each of the diode's placement centers. The thermal paste increases the thermal transfer between the diode and the metal plate used as a circuit. Important to keep in mind the diodes generate a lot of light intensity and very concentrated. Avoid looking directly at them once they are turned on and wear protective glasses when working with them. Characteristic: - Chip 28x47mil - Voltage: 3.1-4.1V - Current: 700mA - Luminous flux: 39-55LM - Ã beam angle: 120 degrees - Color emission: blue Code P0152 Available Price €1.59
WS2812B RGB LED Strip White 1m 30 LED/M IP65 WS2812B RGB LED Strip White 1m 30 LED/M IP65 features: - IP65 RGB Addressable Smart Arduino - RGB LED WS2812B S2812B are LEDs that have integrated logic, so it is possible to vary the color of each LED individually S2812B includes a built-in inside each LED, which allows each pixel to be accessed individually - For this reason, these types of LEDs are called individually indexable - They are based on the 5050 LED - 30 individually indexable LED diodes - 24-bit color control (8-bit PWM per channel) - 16.8 million colors by LED - One-wire communication - Power: 5 V idth: 11 mm - Thickness: 2.6 mm - Length: 1 meter - Consumption: 1.8A (all white) ater resistant Code P0103 Last items in stock Price €9.75
Aluminum Heat Sink 15x2cm LED 1W-3W Aluminum Heat Sink 15cm 2cm LED 1W 3W features:Aluminum heatsink for LED 1W-3W, Length: 15cm, Width: 2.0cm, Height: 0.6cm. Code P0051 Available Price €2.79
LED diode 1W White SMD 130LM Mount LED Diode on a good heatsink, a metal plate, add some fan, this is necessary because you have to " remove "the heat from the surface of the plate so that the LEDs last longer to place a little bit of thermal silicone in each of the centers of placement of the diodes. The thermal paste increases the thermal transfer between the diode and the metal plate used as a circuit. Important to keep in mind the diodes generate a lot of light intensity and very concentrated. Avoid looking directly at them once they are turned on and wear protective glasses when working with them. Characteristic: - Chip 28x47mil - Voltage: 3.0-3.2V - Current: 300mA - Luminous flux: 120-130LM - Beam angle: 130 degrees Code P0043 Available Price €0.98
LED Power Diode COB 10W 3000K White SMD COB LEDs are built as a matrix of LEDs, that is, a concentration of LEDs in a silicone coated tablet. The advantages of LED COB: - A light output of up to 120 lumens / watt (twice as much as LED SMD)- The light intensity is greater without concentrating the beam of light- Greater durability- Angle of opening up to 160ºC- Multidirectional light Mount LED diode on a good heatsink, add some fan, this is necessary because you have to "remove" the heat from the surface of the board so that the LEDs last longer.Place a little thermal silicone in each of the diode placement centers. Code P0148 Available Price €2.11