LED 1W Red SMD

Programmable LED module with flexible display, 256-pixel matrix light, individually addressable. WS2812B are LEDs that have integrated logic, so it is possible to vary the colour of each LED individually. WS2812B has a built-in integrated logic within each LED, which allows access to each pixel individually. For this reason these LEDs are called individually indexable. They are based on the 5050 LED.

COB LEDs are built as a matrix of LEDs, that is, a concentration of LEDs in a silicone coated tablet. The advantages of LED COB: - A light output of up to 120 lumens / watt (twice as much as LED SMD)
- The light intensity is greater without concentrating the beam of light
- Greater durability
- Angle of opening up to 160ºC
- Multidirectional light Mount LED diode on a good heatsink, add some fan, this is necessary because you have to "remove" the heat from the surface of the board so that the LEDs last longer.
Place a little thermal silicone in each of the diode placement centers.

Mount LED Diode on a good heatsink, a metal plate, add a fan, this is necessary because you have to "remove" the heat from the surface of the board so that the LEDs last longer to place a little bit of thermal silicone in each of the diode's placement centers.
The thermal paste increases the thermal transfer between the diode and the metal plate used as a circuit.
Important to keep in mind the diodes generate a lot of light intensity and very concentrated.
Avoid looking directly at them once they are turned on and wear protective glasses when working with them.

Characteristic:

- Voltage: 3.2-3.6V

- Current : 700mA

- Luminous flux: 5-8LM

- Beam angle: 140 degrees

- Colour emission: Ultraviolet

This chain has DC5V LEDs that have built-in logic, so it is possible to vary the colour of each LED individually.

WS2811 includes a built-in integrated inside each LED, which allows access to each pixel individually. Black background

Easy programming with Arduino, ESP32, ESP8266, etc. 

Mount LED Diode on a good heatsink, a metal plate, add a fan, this is necessary because you have to "remove" the heat from the surface of the board so that the LEDs last longer to place a little bit of thermal silicone in each of the diode's placement centers.
The thermal paste increases the thermal transfer between the diode and the metal plate used as a circuit.
Important to keep in mind the diodes generate a lot of light intensity and very concentrated.
Avoid looking directly at them once they are turned on and wear protective glasses when working with them. Characteristic: - Chip 28x47mil
- Voltage: 3.1-4.1V
- Current: 700mA
- Luminous flux: 39-55LM
- Ã beam angle: 120 degrees
- Color emission: blue

3x Power LED Aluminum Heat Sink 3W 5W features:
- Outside diameter: 36mm
- Height: 30mm
- Quantity: 3 units

5x Power LED Aluminum Heat Sink 1W 3W features:
- Outside diameter: 36mm
- Height: 15mm
- Quantity: 5 units

Mount LED Diode on a good heatsink, a metal plate, add a fan, this is necessary because you have to "remove" the heat from the surface of the board so that the LEDs last longer to place a little bit of thermal silicone in each of the diode's placement centers.
The thermal paste increases the thermal transfer between the diode and the metal plate used as a circuit.
Important to keep in mind the diodes generate a lot of light intensity and very concentrated.
Avoid looking directly at them once they are turned on and wear protective glasses when working with them. Characteristic: - Chip 28x47mil
- Voltage: 3.0-3.2V
- Current: 300mA
- Luminous flux: 20-30LM
- Ã beam angle: 120 degrees
- Color emission: blue

Aluminum Heat Sink 15cm 2cm LED 1W 3W features:
Aluminum heatsink for LED 1W-3W, Length: 15cm, Width: 2.0cm, Height: 0.6cm.

Mount LED Diode on a good heatsink, a metal plate, add a fan, this is necessary because you have to "remove" the heat from the surface of the board so that the LEDs last longer to place a little bit of thermal silicone in each of the diode's placement centers.
The thermal paste increases the thermal transfer between the diode and the metal plate used as a circuit.
Important to keep in mind the diodes generate a lot of light intensity and very concentrated.
Avoid looking directly at them once they are turned on and wear protective glasses when working with them. Characteristic: - 32mil Chip
- Voltage: 2.2-2.4V
- Current: 300mA
- Luminous flux: 40-50LM
- Ã Beam angle: 120 degrees
- Color emission: yellow / orange