It allows controlling up to 2 direct current motors or a bipolar stepper motor. It also allows to control a unipolar stepper motor configured as bipolar.
Ideal for projects with ARDUINO.
You can use it with PIC, AVR, STM32.
L298N Motor Drive Controller Board Module Dual H Bridge DC features:
- Minimum operating voltage: 5 V
- Maximum operating voltage: 35 V
- Maximum current: ± 2 A
- Logic voltage: 5V
- PWM signal inputs for speed control
- Outputs: for 2 DC motors or for a bipolar stepper motor
- Measures: 43x43x24 mm
Helpful Links:
Operation of the robot by Infrared / Operation of the robot by Bluetooth / Automatic operation with detection of obstacles

The 28BYJ-48 has everything you need to start using stepper motors in your project
A stepper motor converts digital impulses into small steps of movement in one direction The engine also comes with a ULN2003 engine controller card
Can control two DC motors or a bipolar stepper motor with a maximum amperage of up to 500 mA
Equipped with state indicator LEDs A, B, C, D 5V Stepper Motor 28BYJ-48 + ULN2003 Driver Boat features:
- Engine model: 28BYJ-48
- Phases engine: 4
- Operating voltage: 5V
- Frequency: 100 Hz
- Operating current: 200mA
- Max Power: 20W
- Winding resistance: 70 ohm
- Angle per step: 5,625º
- Steps per round: 64
- Torque: 0.3 Kgr / cm
- Speed: 1900 rpm

The optical module sensor (reflective) with comparator LM393, which detects obstacles with high precision.
The ideal obstacle detection detector for the installation of smart robots.
TCRT5000 - reflective optical sensor that has a compact construction where the light emitter and receiver are placed in the same direction to detect the presence of a object using infrared reflection on the object.
The working wavelength is 950nm.
The transmitter is infrared LED and the phototransistor receiver.
By using LM393 comparator the module has a binary output (D0) that is at level 1 (object is detected).
The sensor allows the detection of an object at a distance of up to 12 mm.

40x Male to male cables 10cm features:
- Length: 10cm
- Quantity: 40 cables
- Dupont male connectors on both ends
- Compatible with 2.54mm female connectors
- High quality and good working condition
- Easy to install and use

Buzzer alarm to convert electrical to acoustic signals in robotics devices and Arduino projects.
Buzzer 5V Active Buzzer 4 to 7V DC features:

- Input voltage: 4V to 7V
- Diameter: 12mm
- Height: 9.5mm
- Spacing Pins: 7.6mm
- Maximum Current:

Electronic Antistatic Wrist Bracelet ESD Blue features:
- Electronic Antistatic Bracelet, blue color
- Protection against electrostatic charges
- Adjustable bracelet with crocodile clip connector
- Material: The conductive elastic band is made of nylon and woven in stainless steel
- Extensible length up to 180 centimeters
- Weight: 25 gr.
- Quantity: 1 loose unit in plastic bag

Push button 6x6x4mm features:
-Touch Push Tact Switch mini electronic Arduino push button
-Measures: 6x6x4.3mm

40x Female Male 10cm features:
- Length: 10cm
- Quantity: 40 cables
- Compatible with 2.54mm male connectors
- High quality and good working conditions
- Easy to install and use

Characteristic:
-10k OHM kΩ - linear potentiometer 10k Arduino
-Tolerance: +/- 20%
- Power: 0.125W

Ideal to power your Arduino board through the power input.
Adapter Battery 9V 6F22 Jack Connector DC features:
- Cable 7cm long
- Battery connector 9V, 6F22
- Male connector DC 5.5 / 2.5

Photoresistance is a resistor whose resistance decreases as the intensity of the light that falls on it increases. 10x Photoresistor GL5539 LDR 50k - 100k features:
- Model: GL5539
- Spectral peak: 540nm
- Maximum DC voltage: 150V
- Maximum power: 100mW
- Resistance with light (10lux): 50-100KΩ
- Resistance with darkness (0lux): 5MΩ
- Response time: 20ms
- Operating temperature: -30ºC - 70ºC

Characteristic: -Length: 20cm
-Quantity: 40 cables
-Mono Dupont connectors on both ends
-Compatible with 2.54mm female connectors
-High quality and good working condition
-Easy to install and use

40x Cables Female-Male 20cm features:
-Length: 20cm
-Quantity: 40 cables
-Connectors have male and female header contacts at either end
-Compatible with female connectors 2,54mm
-High quality and good working conditions
-Easy to install and use

Resistor 150R Ohm 5% 0,25W 1/4W features:
-150R Ohm
-Type: Carbon film
-Tolerance: ±5%
-Power: 0.25W
-Dimensions: 2x7mm

Tower Pro Micro Servo 9g SG90 360 degree features:
- Operating voltage: 3.0-7.2V
- Speed (4.8V without load): 0.12sec / 60 degrees
- Strength: 1.2kg / 42.3oz (4.8V); 1.6 kg / 56.4oz (6.0V)
- Working temperature: -30 to +60 degrees C
- Cable length: approx. 23cm
- Includes photo accessories and screws
- Dimensions: 22x11.5x27mm

5x Push Switch Button B3F Omron Red Key 12mm features:

- 5x Push Buttons B3F Omron Key
- Maximum current: 50 mA
- Tension DC: 24V
- Operating force: 1.27N
- Switch terminals: weldable
- Contact: SPST-NO
- Contact resistance: 100M Ohm
- Type of action: Superficial
- Measures: 12x12x7.3mm

15x Electrolytic Capacitor 4,7uF 50V 105ºC PIC Arduino features:
-Type: Electrolytic Capacitor
-Assembly: intern
-Value: 4.7uF
-Maximum tension: 50V
-Maximum temperature: 105º C
-Dimensions: 5x11mm
-Quantity: 15 units

LCD display consists of a 16-character, 2-rows.
The display is compatible with the HD44780 controller
Ideal for projects with Arduino
You can use it with PIC, AVR, STM32 and many more controllers.

Push button 6x6x4mm features:
-Touch Push Tact Switch mini electronic Arduino push button
-Measures: 6x6x45mm
-Quantity: 1 unit

The 28BYJ-48 has everything you need to start using stepper motors in your project. A stepper motor converts digital impulses into small movement steps. in one direction Characteristic: - Motor model: 28BYJ-48
- Motor phases: 4
- Operating voltage: 5V
- Frequency: 100 Hz
- Operating current: 200mA
- Max Power: 20W
- Winding resistance: 70 ohm
- Angle per step: 5,625º
- Steps per lap: 64
- Torque: 0.3 Kgr / cm
- Speed: 1900 rpm
- Operating temperature: -45ºC to + 125ºC
- Motor cable length: 19cm
- Motor block diameter: 28mm
- Motor dimensions: 42mm x 32mm x 30mm