Push button 6x6x4mm
  • Push button 6x6x4mm

Push button 6x6x4mm

K0079

Push button 6x6x4mm features:
-Touch Push Tact Switch mini electronic Arduino push button
-Measures: 6x6x4.3mm

OEM
Add to wish list
Spend 100€ to get a 3% discount for all your orders within the next 12 months and even higher discounts for higher spend. Click here to review loyalty program rules

Push button 6x6x4mm features:

-Touch Push Tact Switch mini electronic Arduino push button
-Measures: 6x6x4.3mm

Customers who bought this product also bought

30x 1N4007 Rectifier Diodes 1A 1000V DO-41

1N4007 Rectifier Diodes 1A 1000V DO-41 features:
- Standard rectifier diode
- Configuration: Simple
- Reverse voltage: 1000V
- Direct voltage drop: 1V
- Direct direct current: 1A
- Maximum overvoltage current: 30A
- Encapsulated: DO-41
- Operational tension: -65ºC to + 125ºC
- Quantity: 30 units

T0002

Price €0.05

5V Stepper Motor 28BYJ-48 + ULN2003 Driver Boat

The 28BYJ-48 has everything you need to start using stepper motors in your project
A stepper motor converts digital impulses into small steps of movement in one direction The engine also comes with a ULN2003 engine controller card
Can control two DC motors or a bipolar stepper motor with a maximum amperage of up to 500 mA
Equipped with state indicator LEDs A, B, C, D 5V Stepper Motor 28BYJ-48 + ULN2003 Driver Boat features:
- Engine model: 28BYJ-48
- Phases engine: 4
- Operating voltage: 5V
- Frequency: 100 Hz
- Operating current: 200mA
- Max Power: 20W
- Winding resistance: 70 ohm
- Angle per step: 5,625º
- Steps per round: 64
- Torque: 0.3 Kgr / cm
- Speed: 1900 rpm

R0038

Price €2.95

TP4056 Lithium Battery Charger Module 5V Micro USB

TP4056 5V Micro USB Lithium Battery Charger Module features:
- Based on TP4056ES regulator
- Lipo micro USB Li-Ion charger
- Input Voltage: 4.5V - 5.5 VDC
- Full charge voltage: 4.2V +/- 1.5%
- Max Output Current: 1A
- Indicator LED: charging red, charging green
- Operating temperature: -10ºC to + 85ºC
- IN + and IN- connection for electronic circuits
- Battery protection against over-discharge voltage: 2.5V - Protection against over current battery: 3A
- Measurements: 25x19x5 mm
- Ideal for 18650 batteries

A0100

Price €0.99

Development Board Ra-02 LoRa SX1278 Ra-02 Module (433MHz) Long range

NodeMcu module based on ESP8266 controller and programming in Lua language
NodeMcu is equipped with 10 GPIO, PWM, I2C, 1-wire and ADC
ESP8266-12E is an improved version of ESP8266-12
It works as a standard WiFi 802.11 b / g / n 2.4 GHz
USB Communication - CP2102 Chip
Characteristic:
ESP 12E ESP8266 ESP12E NodeMcu Lua Wireless Development Board CP2102 WiFi features:

- Supply voltage: 3.3V (LOGICAL LEVELS: 3.3V)
- Supported protocols: 802.11 b / g / n
- Network support: 2.4 GHz
- Band: 2400 (MHz) - Wi-Fi Direct (P2p), Soft Access Point
- Integrated TCP / IP stack
- PLL, regulators and integrated power management units
- Output power: 0 , 15 (W); + 19.5dBm in 802.11b mode

W0108

Price €8.99

2WD Robot Smart Car Chassis 2x Wheels DIY

Ideal for building a car with obstacle detector, light follower
Includes battery compartment for 4 AA batteries and ignition switch. (batteries not included) 2WD Robot Smart Car Chassis 2x Wheels DIY features:
- Voltage: 3 to 6Vdc
- Speed without load: 100 RPM to 6Vdc
- No-load current: 90mA to 3Vdc - 180mA to 6Vdc
- Dimensions of the wheel: diameter 65mm - width 26 mm

R0003

Price €12.50
€0.21

0,17 tax excl.

Tax included
Price €0.21

Order until 4pm we will send today
30 days return