Ramps 1.4 Reprap - Arduino Mega Pololu Shield RepRap Arduino Mega Pololu Shield (RAMPS) version 1.4 for 3D printer. RAMPS is a shield for the Arduino Mega - The outputs of the Arduino board are redirected to the motor drivers. To have the complete electronics for a 3D printer you need a RAMPS, an Arduino Mega and at least four stepper motor drivers Code I0019 Available Price €4.95
Ramps 1.5 Reprap - Arduino Mega Pololu Shield RepRap Arduino Mega Pololu Shield (RAMPS) version 1.5 for 3D printer. Includes jumpers. RAMPS plate is a shield for the Arduino Mega2560. The outputs of the Arduino board are redirected to the motor drivers. To have the complete electronics for a 3D printer you need a RAMPS, an Arduino Mega and at least four stepper motor drivers A4988, DRV8825. Code I0193 Available Price €5.99
Ramps 1.6 Reprap - Arduino Mega Pololu Shield RepRap Arduino Mega Pololu Shield (RAMPS) version 1.6 for 3D printer. Updated 4-layer PCB control panel motherboard with 5-piece DRV8825 driver for 3D printer. Includes heatsink and jumpers. RAMPS board is a shield for the Arduino Mega2560. The outputs of the Arduino board are redirected to the motor drivers. To have the complete electronics for a 3D printer you need a RAMPS, an Arduino Mega and at least four stepper motor drivers A4988, DRV8825. Code I0194 ✗ Out-of-Stock Price €9.90
MKS PWC V3.0 power auto-off while finish printing module Auto shut down module for MKS GEN L SKR V1.3 MKS PWC automatically turning off after the printing. It helps in the cases like the unexpected power off or you have to leave during the printing, and other similar issues. Code I0187 Available Regular price €17.49 -€4.00 Price €13.49
Printer Heating Controller MKS Mos25 for Heatbed Extruder MOS Module MKS MOS25 is the Mosfet printer heating module for heated bed that supports current up to 25A. We recommend MKS MOSFET, especially if you are trying to use a heated bed with your 3D printer and 12V power supply. Code I0181 Available Regular price €8.49 -10% Price €7.64
Printer Heating Controller MKS Mosfet for Heatbed Extruder MOS Module Printer Heating Controller MKS Mosfet for Heatbed Extruder MOS Module features: - Superior performance of MOSFET- Maximum current - up to 30A (heat sink)- Can use control output signal Ramp1.4 (D8, GND-warm bed) and MKS series- To control - 5-24V digital signal Code I0093 Available Price €9.49
MKS TMC2208 V2.0 + Heatsink Stepstick Stepper Driver Motor for 3D Printer TMC2208 V2.0 Silent Stepstick Stepper, Motor Controller Module + Heatsink Compared to the TMC2100 module, the TMC2208 controller module emits less heat. Code I0180 Available Price €4.95
DRV8825 + Radiator Stepstick Stepper Driver Motor Pololu 3D Printer It has an automatic voltage regulator, which for practical purposes results in quieter operation and less vibrations. Characteristic: - Minimum operating voltage: 8 V - Maximum operating voltage: 45 V - Maximum current: ± 2.5 A (24V, adequately ventilated or refrigerated) - Logic voltage: 3 V / 5.5V - Microstep resolution: full, 1/2, 1/4, 1/8 , 1/16, 1/32 - Factory soldered temples - 4-layer PCB, 2 oz. Copper for improved heat dissipation - Short-circuit and overtemperature protection - Use potentiometer to adjust the current - Measurements: 20x16x12 mm Code I0012 Available Price €3.49
A4988 + RepRap Radiator A4988 + RepRap Radiator features: - Minimum operating voltage: 8 V - Maximum operating voltage: 35 V - Maximum current: ± 2 A (adequately ventilated or refrigerated) - Logic voltage: 3 V / 5.5V - Microstep resolution: full, 1/2, 1/4, 1/8, and 1/16 - Factory soldered temples - Use potentiometer to adjust current - Measurements: 20x16x12 mm Code I0023 Available Price €1.90
A4988 + Stepstick Radiator Stepper Motor Reprap Stepstick A4988 controller Driver for stepper motors Used with Ramps 1.4 - RepRapArduino Mega Pololu Shield A4988 + Stepstick Radiator Stepper Motor Reprap features: - Minimum operating voltage: 8 V - Operating voltage maximum: 35 V - Maximum current: ± 2 A (adequately ventilated or refrigerated) - Logic voltage: 3 V / 5.5V - Microstep resolution: full, 1/2, 1/4, 1/8, and 1/16 - Factory soldered temples - Use potentiometer to adjust current - Measurements: 20x16x12 mm Code I0014 Available Price €1.90