SparkFun Qwiic HAT for Raspberry Pi The Qwiic HAT is an absolute basic of Qwiic system for Raspberry. It enables a quick and efficient connection of an sensor to your Raspberry over I2C bus (GND, 3.3 V, SDA and SCL). As Qwiic enables daisy chaining of components, you can pretty much install as many sensors on the Qwiic HAT as you want. On top of that it fits perfectly Pi Tin enclosure from SparkFun enabling connection while in case. Code SP031 Available Price €7.99
SparkFun 16x2 SerLCD - Black on RGB 3.3V This little PCB piece is a great independent display addition to any project. Why independent? Well, it features an ATmega328P AVR on its back, making it a pretty much an UNO with a screen rather than a screen itself. We have the same screen with a reverse color version, i.e. RGB on black with a reference of SP028 Code SP028 Last items in stock Regular price €27.99 -€10.00 Price €17.99
SparkFun 16x2 SerLCD - RGB on Black 3.3V This little PCB piece is a great independent display addition to any project. Why independent? Well, it features an ATmega328P AVR on its back, making it a pretty much an UNO with a screen rather than a screen itself. We have the same screen with a reverse color version, i.e. black on RGB with a reference of SP028 Code SP027 Last items in stock Regular price €27.99 -€10.00 Price €17.99
SparkFun FTDI Basic Breakout - 3.3V This FTDI breakout is a super small board with a standard FT232RL USB to serial IC circuit. The pinout fits FTDI cable making it compatible with any Arduino or Arduino compatible 5V boards. Code SP024 Available Price €19.99
SparkFun FTDI Basic Breakout - 5V This FTDI breakout is a super small board with a standard FT232RL USB to serial IC circuit. The pinout fits FTDI cable making it compatible with any Arduino or Arduino compatible 5V boards. Code SP023 Available Price €19.99
SparkFun ESP32 Thing The SparkFun ESP32 thing is an upgrade to boards based on the popular ESP8266. What the 32 version has to offer on top? Well one of the largest upgrades is support for Bluetooth communications and nearly 30 I/O pins. Makes it pretty perfect for any IoT solution, right? Code SP009 Last items in stock Price €27.99
SparkFun ESP8266 Thing - Dev Board (with Headers) ESP8266 Thing Dev board from Sparkfun is a reliable, strong solution for IoT projects. The ESP8266 is a well-known WiFi controller from the boards such as NodeMcu and or WeMos. This board increases the reliability to maximum though. This version comes with headers. Code SP008 Last items in stock Price €21.99
SparkFun ESP8266 Thing - Dev Board (wo headers) ESP8266 Thing Dev board from Sparkfun is a reliable, strong solution for IoT projects. The ESP8266 is a well-known WiFi controller from the boards such as NodeMcu and or WeMos. This board increases the reliability to maximum though. This version comes without headers. Code SP007 Last items in stock Price €25.99
SparkFun Pi Servo HAT - Obsolete 16 servo motors with one board seems impossible? With this board not only it isn´t impossible, but it even seems easy. Additionally, you won´t need to sacrifice any of your valuable GPIOs as the HAT connects directly via I2C. Additionally, you have a serial terminal connection at your disposal. You can supply the power to the board through your Pi or directly if you are going for larger servos and would need a separate source of power. Simply scrap a small blob of solder on the isolation jumper. Code SP0016 ✗ Out-of-Stock Price €16.99
SparkFun Pi AVR Programmer HAT - OBSOLETE You are looking for an easy way to program a microcontroller in your Arduino. It has never been easier - with this board you can do it in the record speed with support or Raspberry (or without for that matter, as the HAT works on the standalone basis as well). It was first developed as an in-house solution for Sparkfun production, and for its quality and usefulness ended up in mass production with a solid fan following. The board includes several handy features ranging from the capacitive touch button for a standalone mode to launch programming, LEDs indicating the status of the program upload as well as some whiteboard labels to keep track of your projects. Code SP0017
SparkFun Qwiic pHAT v2.0 for Raspberry Pi QWIIC is a connection standard developed by Sparkfun enabling a quick an easy connection of peripherals without a need to solder pins, without any mismatches due to polarized connector. And on top of that you can "daisy chain" them! This hat pretty much opens the whole QWIIC universe in front of your Pi. It features 4 QWIIC ports all on the same I2C bus (GND, 3.3V, SDA, and SCL). A universal 2x20 GPIO makes it compatible with all Raspberry Pi boards, as well as Google Coral and Jetson Nano. Note: For a secure connection in some applications, you'll need to add a pair of 1x20 stackable headers to extend the pins to your cart. Code SP0020 Backorder Price €7.99
SparkFun WiFi Shield - ESP8266 The SparkFun WiFi ESP8266 Shield is a shield for Arduino R3 R3 board enabling internet connection. ESP8266 as you all know is a solid fundament for any IoT project an in this version it can be simply and easily put on your board. It is a great middle ground between the sole module and the development board such NodeMcu or WeMos. So if you need a relatively cheap and super reliable way to internet for your Arduino project - this is the shield for you! ESP8266 shield WiFi comes with an AT-command firmware, hence can be controlled by any UART. It works great with any Arduino R· layout. The shield doesn´t have the headers on. Code SP006 Last items in stock Price €21.99
SparkFun Ardumoto - Motor Driver Shield The Ardumoto Shield was created based on the L298 H-bridge as a two-motor controller for Arduino. It was designed to be able to drive two DC motors up to 2A per channel. Together with its Arduino, it will provide the perfect platform to control RC vehicles, or small autonomous robots. Its use has been made easier, LEDs with control signal have been added and the possibilities for advanced users have been increased. Code SP011 Available Price €23.99
MyoWare Cable Shield This Shield provides a 3.5mm connector where you can connect a three-electrode sensor cable, allowing you to test and use the MyoWare muscle sensor without actually connecting it to your person. Code SP072 Backorder Price €6.49
MyoWare Shield - Mini protoboard for MyoWare sensor Simple breadboard for your MyoWare Muscle Sensor. You can use the provided area of the shield to solder in any custom circuit you can think of. This shield provides 8 x 15 solderable through holes on a standard 0.1" grid. Code SP070 Last items in stock Price €3.29
MyoWare Muscle Sensor Development Kit - OBSOLETE This is the MyoWare Muscle Sensor Development Kit, an Arduino-powered electromyography (EMG) sensor kit that gives you the MyoWare, each MyoWare Shield and everything you need to connect them all together. Code SP074
MyoWare Power Shield MyoWare Power Shield is designed to use two standard CR2032 coin cell batteries to power the MyoWare muscle sensor. These will be connected in parallel for extended capacity at a nominal 3.0V. Code SP071 Backorder Price €6.49
SparkFun Qwiic Adapter This little board is simply a I2C board to Qwiic converter. It pretty much enables any device with I2C connectors to work with Qwiic system. It has two Qwiic ports - both of them served with the same I2C bus. You simply stick the board on your I2C board and get additional two Qwiic ports. It is as easy as it sounds Code SP033 Available Price €1.89
Sensor Cable - Electrode Pads (3 connector) This is your simple three conductor sensor cable with electrode pad wires. These cables measure 24" long and feature a 3.5mm audio jack on one end with snap type receptacles for biomedical sensor pads. Code SP075 Available Price €8.99
MyoWare 2.0 Cable Shield This Cable Shield provides a 3.5mm connector where you can connect a three-electrode sensor cable, allowing you to test and use the MyoWare 2.0 muscle sensor without actually connecting it to your person. Code SP045 Available Price €7.49
SparkFun micro:climate kit for micro:bit - v3.0 The SparkFun micro:Climate kit is a complete weather station kit that builds on the weather:bit carrier board with weather and soil moisture sensors, all powered by the micro:bit. board. Code SP073 Backorder Price €179.00
SparkFun DataLogger IoT - 9DoF SparkFun DataLogger IoT - 9DoF is a pre-programmed data logger to automatically log IMU, GPS and various pressure, humidity and distance sensors - all without having to write a single line of code! DataLogger automatically detects, configures and logs Qwiic sensors. It is specifically designed for users who only need to capture a large amount of data in a CSV or JSON file and return it to their larger project. Code SP099 Last items in stock Price €94.90
Teensy 4.0 It's a tiny board, programmable from the Arduino IDE, that hides enormous potential. The Teensy 4.0 is equipped with a 32-bit ARM Cortex-M7 processor at a blazingly fast 600 MHz. The use of the NXP iMXRT1062 chip makes the Teensy 4.0 the fastest microcontroller on the market at launch. Code SP101 Available Price €37.89
SparkFun Qwiic Shield for Teensy SparkFun Qwiic Shield for Teensy is a quick and easy way to prepare an expansion board equipped with Qwiic connectors . This shield is compatible with Teensy 4.0, Teensy 3.2 and Teensy LC boards. The board is equipped with an I2C bus connector (GND, 3.3 V, SDA and SCL) and four SparkFun Qwiic connectors Code SP102 Available Price €5.95
SparkFun Weather Meter Kit The SparkFun weather meter kit is a set of basic mechanical components for building a weather station. This kit represents the three basic elements of weather measurement: wind speed, wind direction and precipitation. Whether you are a farmer, a professional meteorologist or a weather enthusiast, building your own weather station can be a truly rewarding project. However, when it comes to measuring the weather, you need some pretty specialised sensors. Code SP090 Last items in stock Price €109.90