Resistor 6,8K Ohm 5% 0,25W 1/4W

20x Electrolytic Capacitor 47uF 50V 105ºC PIC Arduino features:
-Type: Electrolytic Capacitor
-Assembly: intern
-Value: 47uF
-Maximum tension: 50V
-Maximum temperature: 105º C
-Dimensions: 6,3x11mm
-Quantity: 20 units

This switch can be used for development projects and for the industry. All metal parts are not oxidized, the insulation material is of high quality.
Its pins protected by an anti oxidant makes welding much easier. Switch On/On 6-pin 6A SPDT features:
- Type: Latch SPDT
- Material: Plastic, metal
- Maximum operating current and voltage: 3A / 250V, 6A / 125V
- Number of pins: 6
- Pin size: 4.5x2 mm
- Type of current: AC
- Pins to be welded
- Switch action: 2 positions On/On
- Size: 13.2x12.7x33.3mm

Ideal for building a car with obstacle detector, light follower
Includes battery compartment for 4 AA batteries and ignition switch. (batteries not included) 2WD Robot Smart Car Chassis 2x Wheels DIY features:
- Voltage: 3 to 6Vdc
- Speed without load: 100 RPM to 6Vdc
- No-load current: 90mA to 3Vdc - 180mA to 6Vdc
- Dimensions of the wheel: diameter 65mm - width 26 mm

Quartz Crystal Oscillator 16 MHz features:
- Low Profile Crystal Oscillator
- Type: Quartz Crystal 16 MHz
- Frequency: 16 MHz
- Format: Low profile
- Assembly: Intern

IR Remote Control + IR Infrared Receiver VS1838 features:
- The test distance is about 5-8 meters, but practical application depends on environmental factors (such as diaphragm, glass , obstructions or other material blockage) - The CHQ1838 / HX1838 receiver receives the 38kHz signal
- Vcc supply: 3.3V-5V
- IN digital output to connect to the port Arduino I / O
- Remote measurements 85x 40x 5mm
- Includes battery
Useful links for Arduino / Raspberry programming and projects with Arduino boards / Raspberry:
Send / Receive information via IR
- Wiring of the IR Remote control + Infrared IR Receiver VS1838 with the UNO module
- Light a 3mm red LED by Infrared

Resistor 10M Ohm 5% 0,25W 1/4W features:
-10M Ohm
-Type: Carbon film
-Tolerance: ±5%
-Power: 0.25W
-Dimensions: 2x7mm

- It has an Atmega328P chip running at 16Mhz with factory-loaded bootloader
- The Uno R3 module has all the Arduino Uno R3 connectors and is compatible with all Arduino shields
Characteristic:
- ATmega328P 16MHz chip with external quartz crystal
- Microprocessor: ATMega328P
- Operating voltage: 5V
- Input voltage (recommended): 7-12V
- Input voltage (limits): 6-20V
- Clock speed: 16 MHz
- Digital I / O pins: 14 (6 with PWM)
- Analog input pins: 6
- DC current for Pin I / O: 20 mA
- Flash32 KB of which 0.5 KB are used by the bootloader - AtMega328P
- SRAM 2 KB - AtMega328P
- EEPROM 1 KB - AtMega328P
- Communication: USB female Type B

Resistor 5,1K Ohm 5% 0,25W 1/4W features:
-5.1K Ohm
-Type: Carbon film
-Tolerance: ±5%
-Power: 0.25W
-Dimensions: 2x7mm