GP2Y0A21YK0F Infrared IR distance sensor Characteristic: - Supply voltage: 4.5V- 5.5V - Consumption: 30 mA typical - Analog output - Range: 10cm to 80cm - Dimensions: 29x12mm - Cable length: 20cm GP2Y0A21YK0F Sharp Analog IR distance sensor 10CM-80CM Arduino Code S0024 Available Price €8.22
Connector Jack 2.1x5.5mm Power Supply DC Male Jack connectors 2.1mm inside and 5.5mm outside to power devices such as LED strips, CCTV (Cameras), Arduino. Connector Jack 2.1x5.5mm Power Supply DC Male features: - Ideal for connecting without welding- It has two screws in the tip for positive and negative cable screwdriver Code K0023 Available Price €0.66
L298N Motor Drive Controller Board Module Dual H Bridge DC It allows controlling up to 2 direct current motors or a bipolar stepper motor. It also allows to control a unipolar stepper motor configured as bipolar.Ideal for projects with ARDUINO.You can use it with PIC, AVR, STM32. L298N Motor Drive Controller Board Module Dual H Bridge DC features: - Minimum operating voltage: 5 V- Maximum operating voltage: 35 V- Maximum current: ± 2 A- Logic voltage: 5V- PWM signal inputs for speed control- Outputs: for 2 DC motors or for a bipolar stepper motor- Measures: 43x43x24 mm Helpful Links: Operation of the robot by Infrared / Operation of the robot by Bluetooth / Automatic operation with detection of obstacles Code M0100 Available Price €2.31
Micro Servo 9g SG90 Tower Pro Micro Servo 9g SG90 features: - Operating voltage: 3.0-7.2V- Speed (4.8V without load): 0.12sec / 60 degrees- Strength: 1.2kg / 42.3oz (4.8V); 1.6 kg / 56.4oz (6.0V)- Working temperature: -30 to +60 degrees C- Cable length: approx. 23cm- Includes photo accessories and screws- Dimensions: 22x11.5x27mm Code R0013 Available Regular price €2.22 -€0.20 Price €2.02
Resistor 1K Ohm 5% 0,25W 1/4W Resistor 1K Ohm 5% 0,25W 1/4W features:-1 unit - 1K Ohm-Type: Carbon film-Tolerance: ±5%-Power: 0.25W-Dimensions: 2x7mm Code D0076 Available Price €0.07
UNO Board CH340 micro USB clone - It has an Atmega328P chip running at 16Mhz with factory-loaded bootloader- The Uno R3 module has all the Arduino Uno R3 connectors and is compatible with all Arduino shields Characteristic: - Includes USB Cable- ATmega328P 16MHz chip with external quartz crystal- Microprocessor: ATMega328P- Operating voltage: 5V- Input voltage (recommended): 7-12V- Input voltage (limits): 6-20V- Clock speed: 16 MHz- Digital I / O pins: 14 (6 with PWM)- Analog input pins: 6- DC current for Pin I / O: 20 mA- Flash32 KB of which 0.5 KB are used by the bootloader - AtMega328P- SRAM 2 KB - AtMega328P- EEPROM 1 KB - AtMega328P- Communication: micro USB female Type B Code B0053 Available Price €7.93
20x Electrolytic Capacitor 47uF 50V 105ºC PIC for Arduino 20x Electrolytic Capacitor 47uF 50V 105ºC PIC Arduino features:-Type: Electrolytic Capacitor-Assembly: intern-Value: 47uF-Maximum tension: 50V-Maximum temperature: 105º C-Dimensions: 6,3x11mm-Quantity: 20 units Code D0043 Backorder Price €0.06
Motor Support for Arduino Smart Car the robot car motor holder and assembly accessories Code R0050 Available Price €0.79
Mclon Car Chassis 2x DIY Wheels Ideal to build a car with an obstacle detector, light follower Characteristic: - Voltage: 3 to 6Vdc - No load speed: 100 RPM to 6Vdc - No load current: 90mA to 3Vdc - 180mA to 6Vdc - Wheel dimensions: diameter 65mm - width 26mm The kit includes: - aluminum platform - 2x wheels and 2x motors - 1x idler wheel - screws Code R0078 Available Price €19.79
2WD Round Car Chassis 2x Ultrasonic Sensor Contents: - 2x Round transparent chassis plate diameter of 14cm - 2x DC 5V gear motor - 2x 6.5cm wheels (Dia .) x 2.6cm (H) - 2x Encoder discs - 2x Idlers - 2x HC-SR04 ultrasonic sensor, distance meter - 2x Holder for HC-SR04 - 1x Battery holder 2xAA (batteries not included) - Screws for assembly Motor characteristic: - Voltage: 3 at 6Vdc - Reducer: 1:48 - No load speed: 100 RPM at 6Vdc - No load current: 90mA at 3Vdc - 180mA at 6Vdc Code R0005 ✗ Out-of-Stock Regular price €16.49 -€3.00 Price €13.49
4WD Robot Smart Car Chassis 4x Wheels DIY Ideal for building a car with obstacle detector, light follower.Includes battery compartment for 4 AA batteries and ignition switch. (batteries not included). 4WD Robot Smart Car Chassis 4x Wheels DIY features: - Voltage: 3 to 6Vdc- Speed without load: 100 RPM to 6Vdc- No-load current: 90mA to 3Vdc - 180mA to 6Vdc- Dimensions of the wheel: diameter 65mm - width 26 mm Code R0004 Available Regular price €13.13 -€3.00 Price €10.13
Mclon Kit ProtoShield DIY The mClon kit is ideal for building a car with obstacle detection and light tracking. In addition to the platform, the kit contains the basic essentials for building your first robot including the Arduino Uno compatible board, distance sensors and many other components. Check the complete list in the product description Code R0085 ✗ Out-of-Stock Regular price €46.48 -€14.25 Price €32.23
2WD Round Robot Chassis Turtle Car 2x Wheels 3x Plates DIY for Arduino Contents: - 3x Round transparent chassis plate diameter of 14cm - 2x DC 5V gearbox motor - 2x 6.5cm wheels (Dia .) x 2.6cm (H) - 2x Encoder discs - 2x Idlers - 1x Battery holder 2xAA (batteries not included) - Screws for assembly Motor characteristic: - Voltage: 3 to 6Vdc - Reducer: 1:48 - No load speed: 100 RPM at 6Vdc - No load current: 90mA at 3Vdc - 180mA at 6Vdc Code R0007 Available Price €14.54
Mclon Car Chassis 2x DIY Wheels Ideal to build a car with an obstacle detector, light follower Characteristic: - Voltage: 3 to 6Vdc - No load speed: 100 RPM to 6Vdc - No load current: 90mA to 3Vdc - 180mA to 6Vdc - Wheel dimensions: diameter 65mm - width 26mm The kit includes: - aluminum platform - 2x wheels and 2x motors - 1x idler wheel - screws Code R0078 Available Price €19.79
2WD Round Car Chassis 2x Ultrasonic Sensor Contents: - 2x Round transparent chassis plate diameter of 14cm - 2x DC 5V gear motor - 2x 6.5cm wheels (Dia .) x 2.6cm (H) - 2x Encoder discs - 2x Idlers - 2x HC-SR04 ultrasonic sensor, distance meter - 2x Holder for HC-SR04 - 1x Battery holder 2xAA (batteries not included) - Screws for assembly Motor characteristic: - Voltage: 3 at 6Vdc - Reducer: 1:48 - No load speed: 100 RPM at 6Vdc - No load current: 90mA at 3Vdc - 180mA at 6Vdc Code R0005 ✗ Out-of-Stock Regular price €16.49 -€3.00 Price €13.49
4WD Robot Smart Car Chassis 4x Wheels DIY Ideal for building a car with obstacle detector, light follower.Includes battery compartment for 4 AA batteries and ignition switch. (batteries not included). 4WD Robot Smart Car Chassis 4x Wheels DIY features: - Voltage: 3 to 6Vdc- Speed without load: 100 RPM to 6Vdc- No-load current: 90mA to 3Vdc - 180mA to 6Vdc- Dimensions of the wheel: diameter 65mm - width 26 mm Code R0004 Available Regular price €13.13 -€3.00 Price €10.13
Mclon Kit ProtoShield DIY The mClon kit is ideal for building a car with obstacle detection and light tracking. In addition to the platform, the kit contains the basic essentials for building your first robot including the Arduino Uno compatible board, distance sensors and many other components. Check the complete list in the product description Code R0085 ✗ Out-of-Stock Regular price €46.48 -€14.25 Price €32.23
2WD Round Robot Chassis Turtle Car 2x Wheels 3x Plates DIY for Arduino Contents: - 3x Round transparent chassis plate diameter of 14cm - 2x DC 5V gearbox motor - 2x 6.5cm wheels (Dia .) x 2.6cm (H) - 2x Encoder discs - 2x Idlers - 1x Battery holder 2xAA (batteries not included) - Screws for assembly Motor characteristic: - Voltage: 3 to 6Vdc - Reducer: 1:48 - No load speed: 100 RPM at 6Vdc - No load current: 90mA at 3Vdc - 180mA at 6Vdc Code R0007 Available Price €14.54