Motor Nema 23 19.3kg 57HS762804

LCD display consists of a 16-character, 2-rows.
The display is compatible with the HD44780 controller
Ideal for projects with Arduino
You can use it with PIC, AVR, STM32 and many more controllers.

9g digital servo new version of SG90.
POM with Carbon fiber gears set and control arms are more durable use than SG90 nylon gear and more torque.
It is a good choice for park size 3D models , high speed jets and R/C airplane 250 450 RC helicopter Servo 9g SG92r 2.5kg features:
Weight: 9g
Operating voltage: 4.8v Stall torque: 2.5kg /cm(4.8v)
Gear type: POM with carbon fiber
Operating speed: 0.1sec /60degree (4.8v)
Temperature range: 0„ƒ_ 55„ƒ
Dead band width:1us
servo wire length: 25 cm
Servo Plug: JR (Fits JR and Futaba)
servo arms &screws included and fit with Futaba servo arm

ESP32 processor development board with WiFi and Bluetooth (BLE) compatible with Arduino Uno shields. It is much faster than the ESP8266 processor (NodeMCU and the like) . Wemos D1 ESP32 R32 WROOM-32 WiFi and Bluetooth features:
Power: 5-12VDC WiFi 802.11 b / g / n / e / i (802.11n up to 150 Mbps) Bluetooth v4.2 BR / EDR and BLE. Compatible with Arduino Uno shields. 6 Analog input. 20 digital inputs / outputs (3.3V) (with PWM functions, interrupt). UART, SPI, I2C communication. Size: 68Ã — 53 mm Micro USB connection. 4Mbytes Flash Memory 520Kb Clock: 240Mhz (a core dedicated to WiFi processing) Temperature: -40C + 85C Current: 250mA (max) Current in saving mode: 0.15mA Operating current: 20mA (without WiFi) Useful links for Arduino / Raspberry programming and projects with Arduino /

Premium Bobina para Impresora 3D

Imagine the simplicity of the Arduino One connected to the communication module. Seems too good to be true, right? That's Arduino One WiFi. Arduino Uno WiFi REV2 (ABX00021) with its integrated IMU (Inertial Measurement Unit) and WiFi is the ideal board to start making your first Internet application from scratch, or to use in the educational field. It has 14 digital input / output pins (5 of which are PWM outputs), 6 analog inputs, a 16 MHz ceramic resonator, an accelerometer, an RGB LED, a power connector and an ICSP header.

Ideal to control the speed of DC motors. Speed controller for DC motor (PWM) 10V-30VDC 3A 120W features:
- Input voltage: 10-30VAC
- Max output DC current: 3A (max 4A)
- Max power: 120W (in case input voltage> 24V)
- Dimensions: 74x47x28mm
- PWM frequency: 500kHz
- Duty Cycle adjustable: 5% -95%
Please note that the voltage applied to the motor will be the supply voltage applied to the circuit

  - It has an Atmega328P chip running at 16Mhz with factory-loaded bootloader
- The Uno R3 module has all the Arduino Uno R3 connectors and is compatible with all Arduino shields   Characteristic:   - ATmega328P 16MHz chip with external quartz crystal
- Microprocessor: ATMega328P
- Operating voltage: 5V
- Input voltage (recommended): 7-12V
- Input voltage (limits): 6-20V
- Clock speed: 16 MHz
- Digital I / O pins: 14 (6 with PWM)
- Analog input pins: 6
- DC current for Pin I / O: 20 mA
- Flash32 KB of which 0.5 KB are used by the bootloader - AtMega328P
- SRAM 2 KB - AtMega328P
- EEPROM 1 KB - AtMega328P
- Communication: micro USB female 

Camera module for Arduino, Raspberry Pi 2 and Pi 3, B and B +. VGA camera 640x480 OV7670 B 0.3MPx 30fps Cmos features:
> - Input voltage 2.5V-3V
- Operating power 60mW / 15fps VGA YUV
- Resolution VGA 640x480 pixels (30fps)
- Maximum frame rate 30fps VGA
- Flicker 50Hz / 60Hz automatic detection
- Lens size 1/6 "
- Angle of view 25 °
- Sensitivity 1.3V / (lux- seg)
- SCCB (Serial Camera Control Bus) interface
- Output format · 8 Bits
- YUV / YCbCr 4: 2: 2
- RGB 565/555/444
- GRB 4: 2: 2
- RAW RGB data
- High sensitivity Light operation
- Automatic adjustment
- Color level saturation - Edge enhancement
- Noise level