Momentary Switch Push Button Red N/O 7mm Momentary Switch Push Button Red N/O 7mm features: - Momentary pushbutton N/O (normally open)- Red button- Dimensions approx. 7 mm x 27 mm- Recessed with nut and washer- Load current (supported): 1A to 230V / 2A to 125V- Drill to embed: 7 mm +/- 0.2- Operating temperature: -55º to +85ºC Code K0156 Available Price €0.45
2x Protoboard Breadboard 5x7cm EGPC 2x Protoboard Breadboard 5x7cm EGPC features: -PCB dimension: 5x7cm-Hole diameter: 1mm -Pitch: 2.54mm-Bakelite with copper fields Code PB032 Available Price €0.49
MT3608 2A DC Boost Step-Up Adjustable Power Module MicroUSB MT3608 2A DC Boost Step-Up Adjustable Power Module MicroUSB features: - Booster module - The output voltage may be greater than the input voltage - Use a multimeter to check the output voltage and adjust the potentiometer - Input voltage: 2-24V - Output voltage: 5-28V - Current output: 2A - Operating temperature: -40ºC to + 85ºC - Conversion efficiency: up to 93% - Size: 17.5 x 30 mm Code A0065 Available Price €1.69
2x MOC3020 Optocoupler 400V 2x MOC3020 Optocoupler 400V features:-Triac Driver Output Optoisolator-Pack: DIL 6-Electronic voltage forward: 1.15V-Trigger LED current: 30mA-Voltage isolation: 5,300 VAC RMS-Maximum blocking voltage: 400V-Temperature of operation: -40°C a + 85°C Code T0013 Available Price €0.79
Desoldering Wire 2mm High grade in the absorption of tin for professionals.Copper mesh roll for desoldering electronic components.Desoldering Wire 2mm features:- Material: Copper- Length: 1.5m- Width: 2mm Code H0006 Available Price €1.79
DC Step-Down Converter 5A 4-38v to 1.25-36v XL4015 LED LiPo DC Step-Down Converter 5A 4-38v to 1.25-36v XL4015 LED LiPo. Control of voltage and current.Use a multimeter to check the output voltage and adjust the potentiometer. Code A0132 Available Price €3.49
Resettable fuse PTC 900mA 60V DC The PTC polymer fuse is a reusable element protecting the circuit against overload and short circuit. Resettable fuse PTC 900mA 60V DC features: Operation current: 900mA Maximum Voltage: 60V Temperature range: -40 „ƒ to 85 „ƒ Cured, flame retardant epoxy polymer insulating material meets UL 94V-0 requirement 40A shock current Trip current 1.8A 990mW power Min resistance 200mΩ Max. 470mΩ Dimensions A 11.7mm B 15.8mm C 5.1mm D 7.6mm E 3.1mm F 1.1mm Terminal dimensions Ø0.51x7.6mm datasheet Resettable fuse RA Code D0085 Available Price €0.96
LED 3W Blue SMD Mount LED Diode on a good heatsink, a metal plate, add a fan, this is necessary because you have to "remove" the heat from the surface of the board so that the LEDs last longer to place a little bit of thermal silicone in each of the diode's placement centers. The thermal paste increases the thermal transfer between the diode and the metal plate used as a circuit. Important to keep in mind the diodes generate a lot of light intensity and very concentrated. Avoid looking directly at them once they are turned on and wear protective glasses when working with them. Characteristic: - Chip 28x47mil - Voltage: 3.1-4.1V - Current: 700mA - Luminous flux: 39-55LM - Ã beam angle: 120 degrees - Color emission: blue Code P0152 Available Price €1.59
LED RGB 5050 WS2812B White RGB LED SMD5050 WS2812B with white packaging, waterproof level IP20. They are smart that are used to create places with decorative lighting, lighting the information screens located inside and outside facilities. They must be integrated to be operated with the help of any type of smart strip controllers, which can be: autonomous (offline), subordinate (online), light scattering ( to create musical lights) and programmable (control). LED RGB 5050 WS2812B White features: - Power supply: +3.7 - +5.3 VDC - Logic input voltage: VDD-0.5~VDD + 0.5 - Operating temperature: -25 ° C - + 85 ° C - Storage temperature: -40 ° C - + 105 ° C - 4 pins: 1- VDD: LED power supply 2- DOUT: Control data signal output 3- GND: Ground connection Code P0095 Available Price €0.30
LED Power Diode COB 12W White SMD COB LEDs are built as a matrix of LEDs, that is, a concentration of LEDs in a silicone coated tablet. The advantages of LED COB: - A light output of up to 120 lumens / watt (twice as much as LED SMD)- The light intensity is greater without concentrating the beam of light- Greater durability- Angle of opening up to 160ºC- Multidirectional light Mount LED diode on a good heatsink, add some fan, this is necessary because you have to "remove" the heat from the surface of the plate so that the LEDs last longer to place a little bit of thermal silicone in each of the placement centers. the diodes. Code P0030 Available Price €3.38
5x Power LED Aluminum Heat Sink 1W 3W 5x Power LED Aluminum Heat Sink 1W 3W features: - Outside diameter: 36mm- Height: 15mm- Quantity: 5 units Code P0037 Available Price €1.48
LED Diode COB 3W 6000K White SMD COB LEDs are built as a matrix of LEDs, that is, a concentration of LEDs in a silicone coated tablet. The advantages of LED COB: - a light output of up to 120 lumens / watt (twice as much as LED SMD)- the light intensity is greater without the need to concentrate the beam of light- greater durability- opening angle of up to 160ºC- multidirectional light Mount LED diode on a good heatsink, add some fan, this is necessary because you have to "remove" the heat from the surface of the plate so that the LEDs last longer to place a little bit of thermal silicone in each of the placement centers. the diodes.The thermal paste increases the thermal transfer between the diode and the metal plate used as a circuit. Code P0146 Backorder Price €1.32
LED Diode COB 20W 6000K White SMD COB LEDs are built as a matrix of LEDs, that is, a concentration of LEDs in a silicone coated tablet. The advantages of LED COB: - A light output of up to 120 lumens / watt (twice as much as LED SMD)- The light intensity is greater without concentrating the beam of light- Greater durability- Angle of opening up to 160ºC- Multidirectional light Mount LED diode on a good heatsink, add some fan, this is necessary because you have to "remove" the heat from the surface of the plate so that the LEDs last longer to place a little bit of thermal silicone in each of the placement centers. the diodes.The thermal paste increases the thermal transfer between the diode and the metal plate used as a circuit. Code P0032 Available Price €4.49
LED 1W Green SMD Mount LED Diode on a good heatsink, a metal plate, add a fan, this is necessary because you have to "remove" the heat from the surface of the board so that the LEDs last longer to place a little bit of thermal silicone in each of the diode's placement centers. The thermal paste increases the thermal transfer between the diode and the metal plate used as a circuit. Important to keep in mind the diodes generate a lot of light intensity and very concentrated. Avoid looking directly at them once they are turned on and wear protective glasses when working with them. Characteristic: - 30mil chip - Voltage: 3.0-3.2V - Current: 300mA - Luminous flux: 70-80LM - Ã beam angle: 120 degrees - Color emission: green Code P0046 Available Price €0.98
Aluminum Heat Sink 10x2.5cm Power LED 3W 5W The aluminium heatsink for 3W to 5W LEDs. It is 10cm long, 2.5cm wide, 1.0cm high. Code P0049 Available Price €4.49
LED Power Diode COB 7W 3000K White SMD COB LEDs are built as a matrix of LEDs, that is, a concentration of LEDs in a silicone coated tablet. The advantages of LED COB: - A light output of up to 120 lumens / watt (twice as much as LED SMD)- The light intensity is greater without concentrating the beam of light- Greater durability- Angle of opening up to 160ºC- Multidirectional light Mount LED diode on a good heatsink, add some fan, this is necessary because you have to "remove" the heat from the surface of the board so that the LEDs last longer.Place a little thermal silicone in each of the diode placement centers. Code P0143 Available Price €2.11
LED strip Warm white 12V 3528 5m /300 Strip of 300 warm white coloured LED lights, 5 metres long. Code K0284 Available Price €9.75
16 pixel RGB 5050 LED Ring Rainbow WS2812B 5V FC-102 for Arduino WS2812B are LEDs that have built-in logic, making it possible to vary the color of each LED individually. WS2812B includes a integrated inside each LED, which allows each pixel to be accessed individually. For this reason, these types of LEDs are called individually indexable. They are based on the 5050 LED. Code P0156 Available Price €6.90
LED RGB 5050 WS2812B White RGB LED SMD5050 WS2812B with white packaging, waterproof level IP20. They are smart that are used to create places with decorative lighting, lighting the information screens located inside and outside facilities. They must be integrated to be operated with the help of any type of smart strip controllers, which can be: autonomous (offline), subordinate (online), light scattering ( to create musical lights) and programmable (control). LED RGB 5050 WS2812B White features: - Power supply: +3.7 - +5.3 VDC - Logic input voltage: VDD-0.5~VDD + 0.5 - Operating temperature: -25 ° C - + 85 ° C - Storage temperature: -40 ° C - + 105 ° C - 4 pins: 1- VDD: LED power supply 2- DOUT: Control data signal output 3- GND: Ground connection Code P0095 Available Price €0.30
LED Power Diode COB 12W White SMD COB LEDs are built as a matrix of LEDs, that is, a concentration of LEDs in a silicone coated tablet. The advantages of LED COB: - A light output of up to 120 lumens / watt (twice as much as LED SMD)- The light intensity is greater without concentrating the beam of light- Greater durability- Angle of opening up to 160ºC- Multidirectional light Mount LED diode on a good heatsink, add some fan, this is necessary because you have to "remove" the heat from the surface of the plate so that the LEDs last longer to place a little bit of thermal silicone in each of the placement centers. the diodes. Code P0030 Available Price €3.38
5x Power LED Aluminum Heat Sink 1W 3W 5x Power LED Aluminum Heat Sink 1W 3W features: - Outside diameter: 36mm- Height: 15mm- Quantity: 5 units Code P0037 Available Price €1.48
LED Diode COB 3W 6000K White SMD COB LEDs are built as a matrix of LEDs, that is, a concentration of LEDs in a silicone coated tablet. The advantages of LED COB: - a light output of up to 120 lumens / watt (twice as much as LED SMD)- the light intensity is greater without the need to concentrate the beam of light- greater durability- opening angle of up to 160ºC- multidirectional light Mount LED diode on a good heatsink, add some fan, this is necessary because you have to "remove" the heat from the surface of the plate so that the LEDs last longer to place a little bit of thermal silicone in each of the placement centers. the diodes.The thermal paste increases the thermal transfer between the diode and the metal plate used as a circuit. Code P0146 Backorder Price €1.32
LED Diode COB 20W 6000K White SMD COB LEDs are built as a matrix of LEDs, that is, a concentration of LEDs in a silicone coated tablet. The advantages of LED COB: - A light output of up to 120 lumens / watt (twice as much as LED SMD)- The light intensity is greater without concentrating the beam of light- Greater durability- Angle of opening up to 160ºC- Multidirectional light Mount LED diode on a good heatsink, add some fan, this is necessary because you have to "remove" the heat from the surface of the plate so that the LEDs last longer to place a little bit of thermal silicone in each of the placement centers. the diodes.The thermal paste increases the thermal transfer between the diode and the metal plate used as a circuit. Code P0032 Available Price €4.49
LED 1W Green SMD Mount LED Diode on a good heatsink, a metal plate, add a fan, this is necessary because you have to "remove" the heat from the surface of the board so that the LEDs last longer to place a little bit of thermal silicone in each of the diode's placement centers. The thermal paste increases the thermal transfer between the diode and the metal plate used as a circuit. Important to keep in mind the diodes generate a lot of light intensity and very concentrated. Avoid looking directly at them once they are turned on and wear protective glasses when working with them. Characteristic: - 30mil chip - Voltage: 3.0-3.2V - Current: 300mA - Luminous flux: 70-80LM - Ã beam angle: 120 degrees - Color emission: green Code P0046 Available Price €0.98
Aluminum Heat Sink 10x2.5cm Power LED 3W 5W The aluminium heatsink for 3W to 5W LEDs. It is 10cm long, 2.5cm wide, 1.0cm high. Code P0049 Available Price €4.49
LED Power Diode COB 7W 3000K White SMD COB LEDs are built as a matrix of LEDs, that is, a concentration of LEDs in a silicone coated tablet. The advantages of LED COB: - A light output of up to 120 lumens / watt (twice as much as LED SMD)- The light intensity is greater without concentrating the beam of light- Greater durability- Angle of opening up to 160ºC- Multidirectional light Mount LED diode on a good heatsink, add some fan, this is necessary because you have to "remove" the heat from the surface of the board so that the LEDs last longer.Place a little thermal silicone in each of the diode placement centers. Code P0143 Available Price €2.11
LED strip Warm white 12V 3528 5m /300 Strip of 300 warm white coloured LED lights, 5 metres long. Code K0284 Available Price €9.75
16 pixel RGB 5050 LED Ring Rainbow WS2812B 5V FC-102 for Arduino WS2812B are LEDs that have built-in logic, making it possible to vary the color of each LED individually. WS2812B includes a integrated inside each LED, which allows each pixel to be accessed individually. For this reason, these types of LEDs are called individually indexable. They are based on the 5050 LED. Code P0156 Available Price €6.90