Power supply 30V 5A UNI-T UTP3315TFL Stabilized power supply with adjustable voltage in the range of 0 to 30 volts and current in the range of 0 to 5 A. The fan cools the power supply and can operate in constant mode. Power supply 30V 5A UNI-T UTP3315TFL features: - Input voltage: 230VAC - Output voltage: 0-30V adjustable - Output current: 0-5A adjustable - Backlit display - Protection against over-consumption and short circuit - Cooled by fan - Includes crocodile clip cables Uni-T UTP3315TFL datasheet Load Regulation Voltage & lt; = 0.01% + 3mV Current & lt; = 0.2% + 3mA Line Regulation Voltage & lt; = 0.01% + 3mV Current & lt; = 0.1% + 5mA Ripple and Noise Voltage 1mV rms Current 3mA rms Code H0181 Last items in stock Price €119.50
10x Linear Potentiometers 10k OHM kΩ 10x Linear Potentiometers 10k OHM kΩ features:- Horizontal variable resistance PCB- 10k Ohm kΩ Linear- Quantity: 10 units Code K0062 Available Price €0.21
LED Diode COB 3W 3000K White SMD COB LEDs are built as a matrix of LEDs, that is, a concentration of LEDs in a silicone coated tablet. The advantages of LED COB: - a light output of up to 120 lumens / watt (twice as much as LED SMD)- the light intensity is greater without the need to concentrate the beam of light- greater durability- opening angle of up to 160ºC- multidirectional light Mount LED diode on a good heatsink, add some fan, this is necessary because you have to "remove" the heat from the surface of the plate so that the LEDs last longer to place a little bit of thermal silicone in each of the placement centers. the diodes.The thermal paste increases the thermal transfer between the diode and the metal plate used as a circuit. Code P0144 Available Price €1.32
DC Gear Motor 6V 1:48 for Arduino DC Gear Motor 6V 148 Arduino features:- Voltage: 3 to 6Vdc- Speed without load: 100 RPM to 6Vdc- No-load current: 90mA to 3Vdc - 180mA to 6Vdc- Reduction: 1:48 Code R0008 Available Regular price €1.90 -€0.41 Price €1.49
Vertical Slide Switch 3P2T 50V 0.5A 6 DIP pins and 2 positions DPDT. This switch is widely used to control the operation of many small electronic power projects, including volume and other controls for audio video, dimmer controls for lights.It is also a great component for DIY. Vertical Slide Switch 3P2T 50V 0.5A features: - Type: 3P2T- Contact resistance: 30 MΩ max.- Insulation resistance: 100 MΩ- Maximum operating voltage: 50V- Maximum operating current: 0.5A- Can support 500 VAC for 1 minute- Step between pins: 2.54mm / 0.1 "- Pin size: 4.5x0.5x15 / 0.77 "x0.19"- Type of current: DC- Pins to be welded- Switch action: 2 ON / OFF positions- Shape of interrupter: rectangular- Size: 16x6.5x15 / 0.2 "x0.02" Code K0188 Available Price €0.48
Silicone Thermal Conductive Paste H 0.5g Silicone Thermal Conductive Paste 0.5g Heatsink 3D features:It facilitates the transfer of heat between the electronic components and the radiator.It's necessary for the correct operation of any type of temperature sensors.Is characterized by a very good chemical resistance for oxidation, water solutions of acids, alkalis and salts, sulfur dioxide and ammonia. It has a very wide range of working temperatures.-Density at 20°C: 2.58 G/cm3-Points: 350°C-Freezing point: -50°C-Coefficient of refraction: 1.405,- Specific temperature at 50°C: 0.243 Cal/g K-Co-efficient global heat transfer at 0-150°C: 0.88 W/m K-Constant dielectric at 100 Hz: 4.7 (± 0.1)-Cross resistance: 5x10 to power 14 Ohm x cm Code Q0080 Available Price €0.59
Resistors Kit 5% 0,25W 1/4W Resistors Kit 5% 0,25W 1/4W features: -10 pcs - 100 Ohm-10 pcs - 220 Ohm-10 pcs - 1,0k Ohm-10 pcs - 2,2k Ohm-10 pcs - 4,7k Ohm-10 pcs - 10k Ohm-10 pcs - 100k Ohm-Type: Carbon film-Tolerance: ±5%-Power: 0.25W-Dimensions: 2x7mm Code D0071 Available Price €2.80
LED Diode COB 3W 6000K White SMD COB LEDs are built as a matrix of LEDs, that is, a concentration of LEDs in a silicone coated tablet. The advantages of LED COB: - a light output of up to 120 lumens / watt (twice as much as LED SMD)- the light intensity is greater without the need to concentrate the beam of light- greater durability- opening angle of up to 160ºC- multidirectional light Mount LED diode on a good heatsink, add some fan, this is necessary because you have to "remove" the heat from the surface of the plate so that the LEDs last longer to place a little bit of thermal silicone in each of the placement centers. the diodes.The thermal paste increases the thermal transfer between the diode and the metal plate used as a circuit. Code P0146 ✗ Out-of-Stock Price €1.32
LED Diode COB 3W 3000K White SMD COB LEDs are built as a matrix of LEDs, that is, a concentration of LEDs in a silicone coated tablet. The advantages of LED COB: - a light output of up to 120 lumens / watt (twice as much as LED SMD)- the light intensity is greater without the need to concentrate the beam of light- greater durability- opening angle of up to 160ºC- multidirectional light Mount LED diode on a good heatsink, add some fan, this is necessary because you have to "remove" the heat from the surface of the plate so that the LEDs last longer to place a little bit of thermal silicone in each of the placement centers. the diodes.The thermal paste increases the thermal transfer between the diode and the metal plate used as a circuit. Code P0144 Available Price €1.32
5x Power LED Aluminum Heat Sink 1W 3W 5x Power LED Aluminum Heat Sink 1W 3W features: - Outside diameter: 36mm- Height: 15mm- Quantity: 5 units Code P0037 Available Price €1.48
LED 1W UV SMD - Ultraviolet Mount LED Diode on a good heatsink, a metal plate, add a fan, this is necessary because you have to "remove" the heat from the surface of the board so that the LEDs last longer to place a little bit of thermal silicone in each of the diode's placement centers. The thermal paste increases the thermal transfer between the diode and the metal plate used as a circuit. Important to keep in mind the diodes generate a lot of light intensity and very concentrated. Avoid looking directly at them once they are turned on and wear protective glasses when working with them. Characteristic: - Voltage: 3.2-3.6V - Current : 700mA - Luminous flux: 5-8LM - Beam angle: 140 degrees - Colour emission: Ultraviolet Code P0162 Available Price €1.39
16 pixel RGB 5050 LED Ring Rainbow WS2812B 5V for Arduino WS2812B are LEDs that have built-in logic, making it possible to vary the color of each LED individually. WS2812B includes a integrated inside each LED, which allows each pixel to be accessed individually. For this reason, these types of LEDs are called individually indexable. They are based on the 5050 LED. Code P0163 Available Price €4.95
LED 1W Orange SMD Mount LED Diode on a good heatsink, a metal plate, add a fan, this is necessary because you have to "remove" the heat from the surface of the board so that the LEDs last longer to place a little bit of thermal silicone in each of the diode's placement centers. The thermal paste increases the thermal transfer between the diode and the metal plate used as a circuit. Important to keep in mind the diodes generate a lot of light intensity and very concentrated. Avoid looking directly at them once they are turned on and wear protective glasses when working with them. Characteristic: - 32mil Chip - Voltage: 2.2-2.4V - Current: 300mA - Luminous flux: 40-50LM - Ã Beam angle: 120 degrees - Color emission: yellow / orange Code P0045 Available Price €0.98
LED 1W Blue SMD Mount LED Diode on a good heatsink, a metal plate, add a fan, this is necessary because you have to "remove" the heat from the surface of the board so that the LEDs last longer to place a little bit of thermal silicone in each of the diode's placement centers. The thermal paste increases the thermal transfer between the diode and the metal plate used as a circuit. Important to keep in mind the diodes generate a lot of light intensity and very concentrated. Avoid looking directly at them once they are turned on and wear protective glasses when working with them. Characteristic: - Chip 28x47mil - Voltage: 3.0-3.2V - Current: 300mA - Luminous flux: 20-30LM - Ã beam angle: 120 degrees - Color emission: blue Code P0047 Available Price €0.98
RGB LED Smart Strip WS2812B Black 5m 30LED/m IP65 WS2812B are LEDs that have built-in logic, making it possible to vary the color of each LED individually. WS2812B includes a integrated inside each LED, which allows each pixel to be accessed individually. For this reason, these types of LEDs are called individually indexable. Code P0105 Last items in stock Price €29.95
Aluminum Heat Sink 10x2.5cm Power LED 3W 5W The aluminium heatsink for 3W to 5W LEDs. It is 10cm long, 2.5cm wide, 1.0cm high. Code P0049 Available Price €3.49
Module 8 RGB LED WS2812B SMD 5050 Addressable 5050 RGB LED bar (5mm x 5mm) with low current draw. LEDs can be joined by connecting the output of one module to the input of another. Data line with a very specific protocol, requires a real-time microcontroller AVR, Arduino, PIC, mbed, etc. A minimum 8 MHz processor is required. Code M0180 Available Price €3.95
LED Power Diode COB 7W 3000K White SMD COB LEDs are built as a matrix of LEDs, that is, a concentration of LEDs in a silicone coated tablet. The advantages of LED COB: - A light output of up to 120 lumens / watt (twice as much as LED SMD)- The light intensity is greater without concentrating the beam of light- Greater durability- Angle of opening up to 160ºC- Multidirectional light Mount LED diode on a good heatsink, add some fan, this is necessary because you have to "remove" the heat from the surface of the board so that the LEDs last longer.Place a little thermal silicone in each of the diode placement centers. Code P0143 Available Price €2.11
LED Diode COB 3W 3000K White SMD COB LEDs are built as a matrix of LEDs, that is, a concentration of LEDs in a silicone coated tablet. The advantages of LED COB: - a light output of up to 120 lumens / watt (twice as much as LED SMD)- the light intensity is greater without the need to concentrate the beam of light- greater durability- opening angle of up to 160ºC- multidirectional light Mount LED diode on a good heatsink, add some fan, this is necessary because you have to "remove" the heat from the surface of the plate so that the LEDs last longer to place a little bit of thermal silicone in each of the placement centers. the diodes.The thermal paste increases the thermal transfer between the diode and the metal plate used as a circuit. Code P0144 Available Price €1.32
5x Power LED Aluminum Heat Sink 1W 3W 5x Power LED Aluminum Heat Sink 1W 3W features: - Outside diameter: 36mm- Height: 15mm- Quantity: 5 units Code P0037 Available Price €1.48
LED 1W UV SMD - Ultraviolet Mount LED Diode on a good heatsink, a metal plate, add a fan, this is necessary because you have to "remove" the heat from the surface of the board so that the LEDs last longer to place a little bit of thermal silicone in each of the diode's placement centers. The thermal paste increases the thermal transfer between the diode and the metal plate used as a circuit. Important to keep in mind the diodes generate a lot of light intensity and very concentrated. Avoid looking directly at them once they are turned on and wear protective glasses when working with them. Characteristic: - Voltage: 3.2-3.6V - Current : 700mA - Luminous flux: 5-8LM - Beam angle: 140 degrees - Colour emission: Ultraviolet Code P0162 Available Price €1.39
16 pixel RGB 5050 LED Ring Rainbow WS2812B 5V for Arduino WS2812B are LEDs that have built-in logic, making it possible to vary the color of each LED individually. WS2812B includes a integrated inside each LED, which allows each pixel to be accessed individually. For this reason, these types of LEDs are called individually indexable. They are based on the 5050 LED. Code P0163 Available Price €4.95
LED 1W Orange SMD Mount LED Diode on a good heatsink, a metal plate, add a fan, this is necessary because you have to "remove" the heat from the surface of the board so that the LEDs last longer to place a little bit of thermal silicone in each of the diode's placement centers. The thermal paste increases the thermal transfer between the diode and the metal plate used as a circuit. Important to keep in mind the diodes generate a lot of light intensity and very concentrated. Avoid looking directly at them once they are turned on and wear protective glasses when working with them. Characteristic: - 32mil Chip - Voltage: 2.2-2.4V - Current: 300mA - Luminous flux: 40-50LM - Ã Beam angle: 120 degrees - Color emission: yellow / orange Code P0045 Available Price €0.98
LED 1W Blue SMD Mount LED Diode on a good heatsink, a metal plate, add a fan, this is necessary because you have to "remove" the heat from the surface of the board so that the LEDs last longer to place a little bit of thermal silicone in each of the diode's placement centers. The thermal paste increases the thermal transfer between the diode and the metal plate used as a circuit. Important to keep in mind the diodes generate a lot of light intensity and very concentrated. Avoid looking directly at them once they are turned on and wear protective glasses when working with them. Characteristic: - Chip 28x47mil - Voltage: 3.0-3.2V - Current: 300mA - Luminous flux: 20-30LM - Ã beam angle: 120 degrees - Color emission: blue Code P0047 Available Price €0.98
RGB LED Smart Strip WS2812B Black 5m 30LED/m IP65 WS2812B are LEDs that have built-in logic, making it possible to vary the color of each LED individually. WS2812B includes a integrated inside each LED, which allows each pixel to be accessed individually. For this reason, these types of LEDs are called individually indexable. Code P0105 Last items in stock Price €29.95
Aluminum Heat Sink 10x2.5cm Power LED 3W 5W The aluminium heatsink for 3W to 5W LEDs. It is 10cm long, 2.5cm wide, 1.0cm high. Code P0049 Available Price €3.49
Module 8 RGB LED WS2812B SMD 5050 Addressable 5050 RGB LED bar (5mm x 5mm) with low current draw. LEDs can be joined by connecting the output of one module to the input of another. Data line with a very specific protocol, requires a real-time microcontroller AVR, Arduino, PIC, mbed, etc. A minimum 8 MHz processor is required. Code M0180 Available Price €3.95
LED Power Diode COB 7W 3000K White SMD COB LEDs are built as a matrix of LEDs, that is, a concentration of LEDs in a silicone coated tablet. The advantages of LED COB: - A light output of up to 120 lumens / watt (twice as much as LED SMD)- The light intensity is greater without concentrating the beam of light- Greater durability- Angle of opening up to 160ºC- Multidirectional light Mount LED diode on a good heatsink, add some fan, this is necessary because you have to "remove" the heat from the surface of the board so that the LEDs last longer.Place a little thermal silicone in each of the diode placement centers. Code P0143 Available Price €2.11