Momentary Switch Push Button Black N/O 7mm

RGB LED Strip WS2812B Black 1m 30 LED/M IP65 features:
- RGB LED WS2812B
- WS2812B are LEDs that have integrated logic, making it possible to vary the color of each LED in a way individual
- WS2812B includes a built-in inside each LED, which allows each pixel to be accessed individually
- For this reason, these types of LEDs are called individually indexable.
- They are based on the 5050 LEDs
- 30 individually indexable LED diodes
- 24-bit color control (8-bit PWM per channel)
- 16.8 million colors per LED
- Communication One-wire
- Power: 5 V
- Width: 11 mm
- Thickness: 2.6 mm
- Length: 1 meter
- Consumption: 1.8A (all white)
- Waterproof
- With 3M adhesive

Soldering Station 48W features:
- Heating element for soldering iron: 48W
- Temperature: 150 ° C - 480 ° C
- Power: 220-240Vac
- Temperature controlled soldering station 48W,
- Adjust the desired temperature of the soldering iron with the adjustment knob,
- The color-coded areas are similar to the following temperatures:
- Yellow approx. 150 „ƒ
- Orange approx.> 150 to 270 „ƒ
- Red approx.> 270 to 480 „ƒ
- Wait about 2-3 minutes until the solder tip reaches the set temperature.

Relay SRD-05 DC-2P 5V 10A SPDT features:
- Supply voltage: 5V
- Output Current: 10A
- For power switching with 5V DC signals - Microcontroller, Arduino, Electronica

This module adapted for the arduino is a unipolar Ic Hall effect magnetic sensor. The Hall effect is when a current passes through a bar of semiconductor (or conductive) material, and if an induction magnetic field B is applied perpendicular to the direction of current flow, a voltage, called Hall voltage, proportional to the magnetic field, and the current appears on the faces sides of the bar. This tension is proportional to the displacement speed of the charge carriers, which is considerably higher in semiconductor materials than in metal conductors. Hall Effect Sensor Module KY-003 with SH3144E TO-92 features:
- 3-pin connector: 1- GND
2- VCC
3- Voltage is recovered depending on the magnetic effect
- Supply voltage: 5VDC
- Output current: 40mA

The module has two outputs: analog A0 and digital D0
Digital output D0 - signal 0 appears or 1 depending on the threshold setting
The threshold is set with the potentiometer
The sensor can be used for example:
Automatic watering for potted plants
With this module you will be able to measure the humidity of the soil, so that you will be able to control the humidity level of the soil of your plants
Characteristic:
Operation: 3.3V -5V
- Sensitivity adjustable by potentiometer
- Dual output mode: analog and digital
- Red LED - power indicator
- Green LED - indicator digital switching output
- PCB measurements: 3 x 1.5 cm
- Probe measurements: 6 x 3 cm

2x LM317T Voltage Regulator DC-DC 1.2V - 37V 1.5A TO-220 features:
- Output type: adjustable
- Voltage Output: 1.2V to 37V
- Manufacturer: ST Microelectronics
- Current Output: 1.5A
- Input voltage Vi- Max Vo: 40V
- Operating temperature: 0ºC to + 125ºC
- Encapsulated: TO-220
- Polarity: Positive
- Quantity: 2 units

It has an ATMega328P chip running at 16Mhz with a factory loaded bootloader
Characteristic:
- Microcontroller: ATmega328
- Operating Voltage (logic level): 5V
- Input Voltage (recommended): 7-12V
- Digital I / O Pins: 14 (6 PWM outputs)
- Analog Inputs: 8 (A0-A7)
- DC Current per Pin I / O 40 mA
- Flash Memory: 32 KB (2 KB used by the bootloader)
- SRAM: 2 KB
- EEPROM: 1 KB
- Clock Frequency: 16 MHz
- USB Communication - CH340
- Dimensions: 18 mm x 44 mm

Fan 12V 2x 3D Printer Cables features:
- Voltage: 12V
- Consumption: 65mA
- Speed: 3800rpm -5600rpm - Noise level: 25dB ± 10%
- Screw diameter: 4.5mm
- Service Life Time: 35000 hours
- Operating temperature: -10 ° C to 65 ° C
- Cable length: 11cm
- Dimensions: 40mm x 40mm x 10mm